2000 TOYOTA TUNDRA Owners Manual

TUNDRA (34413U)
105
SHIFTING BETWEEN º2WDº AND º4HIº
To shift from º2WDº to º4HIº, reduce
the vehicle speed to less than 100 km/h
(62 mph) and push in the º2WD/4HIº but-
ton.
If the 4HIº (high speed four- wheel drive)
indicator light flashes when you push in
the º2WD/4HIº button, this reminds you
that the transfer mode is not securely in
º4HIº mode. Drive straight ahead while
accelerating or decelerating.
If the 4HIº (high speed four- wheel drive)
indicator light flashes and the buzzer
sounds when you push in the º2WD/4HIº
button, this reminds you that the transfer
mode is not in º4HIº mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Push the button
to turn it off, then once again to turn it
back on.
CAUTION
Never push the º2WD/4HIº button if
the wheels are slipping. Stop the slip-
ping or spinning before shifting.
To shift from º4HIº to º2WDº, push the
º2WD/4HIº button again to turn it off.
This can be done at any speed.
If the 4HIº (high speed four- wheel drive)
indicator light flashes when you push the
º2WD/4HIº button again to return to 2WDº
mode, this reminds you that the transfer
mode is not securely in º2WDº mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distance. SHIFTING BETWEEN º4HIº AND º4LOº
To shift from º4HIº to º4LOº,
stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º4LOº button. If the º2WD/4HIº button left
out, push in the º2WD/4HIº button to se-
lect the º4HIº mode.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4LOº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
To shift from º4LOº to º4HIº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º4LOº button.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4HIº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
(c) Shifting procedure
(button type)
ProCarManuals.com

TUNDRA (34413U)
106
SHIFTING BETWEEN º2WDº AND º4LOº
To shift from º2WDº to º4LOº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º2WD/4HIº button in to select the º4HIº
mode, then push the º4LOº button.
If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
º4LOº button, this reminds you that the
transfer mode is not in º4LOº mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into ºNº and push
the button again.
To shift from º4LOº to º2WDº, stop the
vehicle and put the transmission into ºNº.
With the brake pedal depressed, push the
º2WD/4HIº switch again to turn it off. If the 4LOº (low speed four- wheel drive)
indicator light flashes and the buzzer
sounds when you push the º2WD/4HIº but-
ton, this reminds you that the transfer
mode is not in º2WDº mode. Push the
º2WD/4HIº button in to return to º4LOº
mode, drive forward or backward in a
short distance, then stop the vehicle com-
pletely, put the transmission securely into
ºNº and push the º2WD/4HIº button once
again.
If the 4LOº (low speed four- wheel drive)
indicator light flashes when you push the
º2WD/4HIº button, this reminds you that
the transfer mode is not in º2WDº mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distanse.
Parking brake
Pedal type
Lever type
ProCarManuals.com

TUNDRA (34413U)
107
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
Pedal typeÐ
To set: Fully depress the parking brake
pedal. For better holding power, first de-
press the brake pedal and hold it while
setting the parking brake.
To release: Depress the parking brake
pedal once again.
Lever typeÐ
To set: Pull out on the lever. For better
holding power, first depress the brake
pedal and hold it while setting the parking
brake.
To release: Press the lock release button,
turn the lever, and push it in.
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down the grades. On steeper hills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION

To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snow- covered) or
winding roads.

Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TURNING ON THE SYSTEM
To operate the cruise control, press the
CRUISE ON- OFFº button. This turns the
system on. The indicator light in the
instrument panel shows that you can now
set the vehicle at a desired cruising
speed. Another press will turn the system
completely off.
CAUTION
To avoid accidental cruise control en-
gagement, keep the CRUISE ON-
OFFº switch off when not using the
cruise control.
ProCarManuals.com

TUNDRA (34413U)
108
SETTING AT A DESIRED SPEED
On vehicles with automatic transmission,
the transmission must be in Dº before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push the lever down in the SET/COASTº
direction and release it. This sets the ve-
hicle at that speed. If the speed is not
satisfactory, tap the lever up for a faster
speed, or tap it down for a slower speed.
Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your
foot off the accelerator pedal.If you need accelerationÐfor example,
when passingÐdepress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise control
on, do not shift to neutral without
depressing the clutch pedal, as this
may cause engine racing or overrev-
ving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:
a. Pulling the lever in the CANCELº
direction and releasing it
b. Depressing the brake pedal
c. Depressing the clutch pedal (manual
transmission)
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out. If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.
RESETTING TO A FASTER SPEED
Push the lever up in the RES/ACCº direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held up, the vehicle will gradually
gain speed.
However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the SET/COASTº direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the SET/COASTº
direction and hold it. Release the lever
when the desired speed is attained. While
the lever is held down, the vehicle speed
will gradually decrease.
However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the SET/COASTº direction.
ProCarManuals.com

TUNDRA (34413U)
109
On vehicles with automatic transmission,
even if you turn off the overdrive switch
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by pulling
the control lever or by depressing the
brake pedal or clutch pedal, pushing the
lever up in the RES/ACCº direction will
restore the speed set prior to cancellation.
However, once the vehicle speed falls be-
low about 40 km/h (25 mph), the preset
speed will not be resumed.CRUISE CONTROL FAILURE WARNING
If the CRUISEº indicator light in the
instrument cluster flashes when using the
cruise control, press the CRUISE ON-
OFFº button to turn the system off and
then press it again to turn it on.
If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.

The indicator light does not come on.

The indicator light flashes again.

The indicator light goes out after it
comes on.
If this is the case, contact your Toyota
dealer and have your vehicle inspected.
Clutch start cancel switch
To crank the engine without depressing
the clutch pedal, push the switch with
the ignition on.
The switch stays on as long as the igni-
tion is on. And it will automatically turn off
when the ignition is off. An indicator light
will illuminate to indicate the system is
operating.
This switch cancels the clutch start sys-
tem, which is designed to keep the starter
motor from operating if the clutch pedal is
not depressed all the way down.
The switch allows the vehicle to be driven
out of difficult situations by cranking the
engine with the clutch engaged.
ProCarManuals.com

TUNDRA (34413U)
11 0
Never use the switch for normal engine
starting. Be sure to follow the starting
procedure instructed in How to start the
engineº in Part 3.
ProCarManuals.com

TUNDRA (34413U)
111
Part 1
OPERATION OF
INSTRUMENTS AND
CONTROLSÐ
Chapter 1- 7
Car audio system
Reference
 Using your audio system:
some basics
 Using your audio system:
controls and features
 Car audio system operating hints
Type 1: AM´FM ETR radio/cassette´com-
pact disc auto changer controller
Type 2: AM´FM ETR radio/cassette player/
compact disc auto changer controller
Type 3: AM´FM ETR radio/cassette player/
compact disc player/compact disc auto
changer controller
Car audio systemÐ
ÐReference
ProCarManuals.com

TUNDRA (34413U)
11 2
Type 4: AM´FM ETR radio/cassette player/
compact disc auto changer controller/
compact disc auto changer
Type 5: Compact disc player
This section describes some of the basic
features on Toyota audio systems. Some
information may not pertain to your sys-
tem.
Your audio system works when the ignition
key is in the ACCº or ONº position.
TURNING THE SYSTEM ON AND OFF
Push PWR/VOLº or PWR´VOLº to turn
the audio system on and off.
Push AMº, FM1´2º, TAPEº, CDº or
AUXº to turn on that function without
pushing PWR/VOLº or PWR´VOLº.
You can turn on each player by inserting
a cassette tape or compact disc.
You can turn off each player by ejecting
the cassette tape or compact disc. If the
audio system was previously off, then the
entire audio system will be turned off
when you eject the cassette tape or com-
pact disc. If another function was pre-
viously playing, it will come on again.
SWITCHING BETWEEN FUNCTIONS
Push AMº, FM1´2º, TAPEº, CDº or
AUXº if the system is already on but you
want to switch from one function to anoth-
er.TONE AND BALANCE
For details about your system's tone and
balance controls, see the description of
your own system.
Tone
How good an audio program sounds to
you is largely determined by the mix of
the treble, midrange, and bass levels. In
fact, different kinds of music and vocal
programs usually sound better with differ-
ent mixes of treble, midrange and bass.
Balance
A good balance of the left and right stereo
channels and of the front and rear sound
levels is also important.
Keep in mind that if you are listening to
a stereo recording or broadcast, changing
the right/left balance will increase the vol-
ume of one group of sounds while de-
creasing the volume of another.
ÐUsing your audio system:
some basics
ProCarManuals.com