2000 TOYOTA CAMRY Oil pan

10. INSTALL FRONT EXHAUST PIPE
(a) Place 2 new gaskets on the front and rear of the front
exhaust pipe.
(b) Temporarily install the 2 bolts and 2 new nuts holding
front exhaust pipe to the center exhaust pipe.
(c) Using a 14 mm deep socket wrench, install the 3 new
nuts holding the front exhaust pipe to the WU±TWC.
Torque: 62 N±m (630 kgf±cm, 46 ft±lbf)
(d) Tighten the 2 bolts and 2 nuts holding front exhaust
pipe to the center exhaust pipe.
Torque: 56 N±m (570 kgf±cm, 41 ft±lbf)
(e) Install the bracket with the 2 bolts.
11. CONNECT NEGATIVE (±) TERMINAL CABLE TO
BATTERY
12. FILL WITH ENGINE OIL (See page EG1±275)
13. START ENGINE AND CHECK FOR LEAKS
14. RECHECK ENGINE OIL LEVEL
15. INSTALL HOOD (c) Install the oil pan with 17 bolts and 4 nuts.
Torque: 5.4 N±m (55 kgf±cm, 48 in.±lbf)
(d) Install the dipstick.
9. INSTALL STIFFENER PLATE
Install the stiffener plate with the 3 bolts.
Torque: 37 N±m (380 kgf±cm, 27 ft±Ibf)
± 5S±FE ENGINELUBRICATION SYSTEMEG1±285

SERVICE SPECIFICATIONS
SERVICE DATA
TORQUE SPECIFICATIONS
Front exhaust pipe x Center exhaust pipe
Oil cooler x Cylinder block (Relief valve)Oil pump pulley x Oil pump drive shaftOil pump body cover x Oil pump body
No.2 idler pulley x Cylinder block
Oil cooler x Cylinder block (Nut)Front exhaust pipe x WU±TWC Stiffener plate x Transaxle caseStiffener plate x Cylinder block Oil strainer x Cylinder blockOil pump x Cylinder block
Oil pan x Cylinder block Oil strainer x Oil pumpOil pan x Drain plug
Oil pan x Oil pumpBody clearance
Part tightened Tip clearance Oil pressure
Oil pump
± 5S±FE ENGINELUBRICATION SYSTEMEG1±289

Tube Type
ANTI±RUST TREATMENT
When replacing body panels, always apply body sealer, anti±rust agent or undercoat according to the re-
quirements of your country.
HINT: For further details, see the description given in Section AR of this manual.
BODY SEALER
Apply body sealer to the
required areas.ANTI±RUST AGENT (WAX)
Cartridge Type
Apply anti±rust agent to
following sections.

Inside of the hems of the
doors and hood.

Around the hinges of the
doors and hood.

Inside of the welded parts
with boxed cross±section.
UNDERCOAT
Apply undercoat to the underbody and
wheel housings.
Spray Gun Undercoating
(Oil base)Undercoating
(Water base)
INTRODUCTIONIN-13

High Strength Sheet Steel
HIGH±STRENGTH STEEL (HSS) PARTS
Generally, High±Strength Steel (HSS) is that which has an intensity value of at 35 kgf/mm2
(343 MPa), and
distinguished from mild steel.
The handling of HSS is the same as for mild steel, but the following should be observed.
1. Panel Hammering: Because HSS is thinner than mild steel, care should be taken to avoid warping
during hammering operations.
2. Removing Spot Welds: Because HSS is tougher than mild steel, damage will occur more easily to a
regular drill. Therefore, an HSS Spot Cutter is recommended.
Also, use a high±torque drill at low speed, and supply grinding oil to the drill during use.
3. Panel Welding: Panel welding procedures for HSS are exactly the same as for mild steel. Plug weld-
ing should be done with MIG (Metal Inert Gas) welder. Do not gas weld or braze panels at areas other
than specified.
BODY PANEL CONSTRUCTIONCN-2

BODY PANEL UNDERCOATING AREAS
HINT:
1. First wipe off any dirt, grease or oil with a rag soaked in a grease, wax and silicone remover.
2. Cover the surrounding areas with masking paper to avoid coating unnecessary areas. If other areas
are accidently coated, wipe off the coating immediately.
3. Apply the first coating of undercoat to all welded areas and panel joints, then apply a second coat
over the entire area.
4. Do not coat parts which become hot, such as the tailpipe, or moving parts, such as the propeller
shaft.
5. Besides the locations described below, apply undercoating to all weld points under the body to insure
corrosion prevention.
6. Be sure to seal the edge of the flange of the member and bracket with undercoating.
7. If undercoat is damaged by peeling, cracks, etc., be sure to repair as necessary.
8. Before the undercoat apply sealer allowing rust prevention to be attained.
REFERENCE: Referring to the notes above, undercoating should be applied according to the specifications
for your country.
ANTI±RUST TREATMENTAR-8

CAMRY ± NEW FEATURES
150NF122
Pressure BulkheadPropellant Grain
Gas
Initiator
CAUTION
The initiator is ignited even by a feeble current. As it is dangerous, never measure the resistance of the
initiator with a volt / ohmmeter, etc.
150NF123
Pressure Bulkhead
Propellant GrainInitiator
Gas
: Propagation of Fire
: Flow of Gas
20
Inflator and Bag
1) Construction
The inflator and bag are integrated inside the case and located in the outer side of the seat back. The infla-
tor is comprised of a initiator, propellant grain, gas and pressure bulkhead.
The bag is made of strong nylon cloth and becomes inflated by the gas heated by the inflator.
2) Operation
When the side airbag sensor detects the acceleration because of a side collision, the ECU appraises the
extent of the acceleration to determine whether or not the side airbag must be deployed.
After the ECU determines that the side airbag must be delpoyed, it causes the initiator to ignite in order
to head and expand the gas inside the inflator. The expanded gas tears thhe pressure bulkhead and flows
into the bag.
The bag, which is inflated by the gas, pushes open the case in the seat, tears the sewn portion of the seat
outer cover, and expands to the side of the occupant.
The expanded bag receives the occupant's arm and chest, and discharges the gas through the bag's surface
in order to soften the rcoil.
Thus, the side airbag helps to reduce the impact energy that is applied to the occupant's arm and chest
areas.

'99camry U
5
Indicator symbols on the instrument panel
Brake system warning light*
1
Seat belt reminder light*
1
Discharge warning light*
1
Malfunction indicator lamp*
1
Low oil pressure warning light*
1
Anti-lock brake system warning light*
1
(type A)
(type B)
Open door warning light*
1
Rear light failure warning light*
1
(type A)
(type B)
SRS airbag warning light*
1
Low windshield washer fluid level warning light*
1

'99camry U
201
Air conditioning control panel, car au-
dio, instrument panel,
console panel,
and switches
Use a soft damp cloth for cleaning.
Soak a clean soft cloth in water or luke-
warm water then lightly
wipe off dirt.
NOTICE
Do not use organic substances (sol-
vents, kerosene, alcohol,
gasoline,
etc.) or alkaline or acidic solutions.
These chemicals can cause discol-
oring, staining or peeling of the
surface.
If you use cleaners or polishing
agents, make sure their ingredients
do not include the substances men-
tioned above.
If you use a liquid car freshener, do
not spill the liquid onto the ve-
hicle's interior surfaces. It may con-
tain the ingredients mentioned
a-
bove. Immediately clean any spill
using the method mentioned above.
Leather Interior
The leather upholstery may be cleaned
with neutral detergent for wool.
Remove dirt using a soft cloth dampened
with 5% solution of neutral detergent for
wool. Then thoroughly wipe off all traces
of detergent with a clean damp cloth.
After cleaning or whenever any part of the
leather gets wet, dry with a soft clean
cloth. Allow the leather to dry in a venti-
lated shaded area.
NOTICE
If a stain should fail to come out
with a neutral detergent, apply a
cleaner that does not contain an
organic solvent.
Never use organic substances such
as benzine, alcohol or gasoline,
or
alkaline or acid solutions for clean-
ing the leather as these
could
cause discoloring.
Use of a nylon brush or synthetic
fiber cloth, etc. may scratch the
fine grained surface of the leather.
Mildew may develop on soiled leath-
er upholstery. Be especially careful
to avoid oil spots. Try to keep your
upholstery always clean.
Long exposure to direct sunlight
may cause the leather surface to
harden and shrink. Keep your ve-
hicle in a shaded area, especially in
the summer.
The interior of your vehicle is apt
to heat up on hot summer days,
so
avoid placing on the upholstery
items made of vinyl or plastic or
containing wax as these tend to
stick to leather when warm.
Improper cleaning of the leather up-
holstery could result in discolor-
ation or staining.
If you have any questions about the
cleaning of your Toyota, your local
Toyota dealer will be pleased to answer
them.