2000 TOYOTA CAMRY length

PP0MS±01
PP±100
± PREPARATIONSUPPLEMENTAL RESTRAINT SYSTEM
152 Author: Date:
EQUIPMENT
Torque wrench
Bolt: Length: 35 mm (1.38 in.) Pitch: 1.0 mm (0.039 in.)
Diam.: 6.0 mm (0.236 in.)Airbag disposal
Tire Width: 185 mm (7.28 in.) Inner diam.: 360mm (14.17 in.)Airbag disposal
Tire with disc wheel Width: 185 mm (7.28 in.)
Inner diam.: 360 mm (14.17 in.)Airbag disposal
Vinyl bagAirbag disposal

SS0AD±03
SS±6
± SERVICE SPECIFICATIONSENGINE MECHANICAL (5S±FE)
169 Author: Date:
ENGINE MECHANICAL (5S±FE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,226 kPa (12.5 kgf/cm2, 178 psi) or more
981 kPa (10.0 kgf/cm2, 142 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim (for repair part) Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.19 ± 0.29 mm (0.007 ± 0.011 in.)
0.28 ± 0.38 mm (0.011 ± 0.015 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 ± 12° BTDC @ idle
Idle speed±700 ± 50 rpm
Idler pulley
tension springFree length
Installed load at 50.5 mm (1.988 in.)42.0 mm (1.654 in.)
32 ± 37 N (3.25 ± 3.75 kgf, 7.2 ± 8.3 lbf)
Cylinder headWarpage
Cylinder block side Maximum
Manifold sideMaximum
Valve seat
Refacing angle
Contacting angle
Contacting width
0.05 mm (0.0020 in.)
0.08 mm (0.0031 in.)
30°, 45°, 75°
45°
1.0 ± 1.4 mm (0.039 ± 0.055 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.056.010 ± 6.030 mm (0.2366 ± 0.2374 in.)
11.048 ± 11.059 mm (0.4331 ± 0.4342 in.)
11.050 ± 11.077 mm (0.4350 ± 0.4361 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Vale face angle
Stem diameterIntake
Eh t
97.40 ± 97.80 mm (3.8346 ± 3.8504 in.)
98.25 ± 98.65 mm (3.8681 ± 3.8839 in.)
97.1 mm (3.823 in.)
98.0 mm (3.858 in.)
44.5°
5.970 ± 5.985 mm (0.2350 ± 0.2356 in.)
5 965 5 980 (0 2348 0 2354 i )Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum5.965 ± 5.980 mm (0.2348 ± 0.2354 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
0.8 ± 1.2 mm (0.031 ± 0.047 in.)
0.5 mm (0.020 in.)
Valve springDeviation Maximum
Free length
Installed tension at 34.7 mm (1.366 in.)2.0 mm (0.079 in.)
40.95 ± 42.80 mm (1.6122 ± 1.6850 in.)
164 ± 189 N (16.7 ± 19.3 kgf, 36.8 ± 42.5 lbf)

SS076±02
± SERVICE SPECIFICATIONSENGINE MECHANICAL (1MZ±FE)
SS±11
174 Author: Date:
ENGINE MECHANICAL (1MZ±FE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,500 kPa (15.3 kgf/cm2, 218 psi)
1,000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim for repair part Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 ± 12° BTDC @ idle
Idle speed±700 ± 50 rpm
Timing belt
tensionerProtrusion from housing side10.0 ± 10.8 mm (0.394 ± 0.425 in.)
Cylinder headWarpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
12 pointed head cylinder head bolt diameter
at tension portion STD
Minimum0.10 mm (0.039 in.)
30°, 45°, 75°
45°
1.0 ± 1.4 mm (0.039 ± 0.055 in.)
10.295 ± 10.313 mm (0.4053 ± 0.4080 in.)
10.345 ± 10.363 mm (0.4073 ± 0.4080 in.)
8.95 ± 9.05 mm (0.3524 ± 0.3563 in.)
8.75 mm (0.3445 in.)
Valve guide
bushingInside diameter
Outside diameter for repair part STD
O/S 0.055.510 ± 5.530 mm (0.2169 ± 0.2177 in.)
10.333 ± 10.344 mm (0.4068 ± 0.4072 in.)
10.383 ± 10.394 mm (0.4088 ± 0.4092 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Maximum95.45 mm (3.5779 in.)
95.40 mm (3.7559 in.)
94.95 mm (3.7382 in.)
94.90 mm (3.7362 in.)
44.5°
5.470 ± 5.485 mm (0.2154 ± 0.2159 in.)
5.465 ± 5.480 mm (0.2152 ± 0.2157 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)

SS±12
± SERVICE SPECIFICATIONSENGINE MECHANICAL (1MZ±FE)
175 Author: Date:
Valve springDeviation Maximum
Free length
Installed tension at 33.8 mm (1.331 in.)2.0 mm (0.079 in.)
45.50 mm (1.7913 in.)
186 ± 206 N (19.0 ± 21.0 kgf, 41.9 ± 46.3 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum30.966 ± 30.976 mm (1.2191 ± 2.2195 in.)
31.000 ± 31.016 mm (1.2205 ± 1.2211 in.)
0.024 ± 0.050 mm (0.0009 ± 0.0020 in.)
0.07 mm (0.0028 in.)
CamshaftThrust clearance STD
Maximum
Journal oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Journal diameter
Circle runout Maximum
Cam lobe height STD Intake
Exhaust
Minimum Intake
Exhaust
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0.040 ± 0.090 mm (0.0016 ± 0.0035 in.)
0.12 mm (0.0047 in.)
0.035 ± 0.072 mm (0.0014 ± 0.0028 in.)
0.025 ± 0.062 mm (0.0010 ± 0.0024 in.)
0.10 mm (0.0039 in.)
0.09 mm (0.0035 in.)
26.959 ± 26.975 mm (1.0613 ± 1.0620 in.)
0.06 mm (0.0024 in.)
42.11 ± 42.21 mm (1.6579 ± 1.6618 in.)
41.96 ± 42.06 mm (1.6520 ± 1.6559 in.)
41.96 mm (1.6520 in.)
41.81 mm (1.6461 in.)
0.020 ± 0.200 mm (0.0008 ± 0.0079 in.)
0.30 mm (0.0188 in.)
18.2 ± 18.8 mm (0.712 ± 0.740 in.)
Air intake
chamberWarpage Maximum0.10 mm (0.0039 in.)
Intake
manifoldWarpage
Air intake chamber side Maximum
Cylinder head side Maximum
0.15 mm (0.0059 in.)
0.08 mm (0.0031 in.)
Exhaust
manifoldWarpage Maximum0.50 mm (0.0196 in.)
Cylinder blockCylinder head surface warpage Maximum
Cylinder bore diameter
Maximum
12 pointed head main bearing cap bolt diameter
at tension portion STD
Minimum0.07 mm (0.0028 in.)
87.500 ± 87.512 mm (3.4449 ± 3.4453 in.)
87.52 mm (3.4457 in.)
7.500 ± 7.600 mm (0.2953 ± 0.2992 in.)
7.20 mm (0.2835 in.)
Piston and
piston ringPiston diameter
AISIN made
at 23.2 mm (0.913 in.) from the piston head
MAHLE made
at 41.2 mm (1.622 in.) from the piston head
Piston oil clearance
AISIN made STD
Maximum
MAHLE made STD
Maximum
Piston ring groove clearance No.1
No.2
Piston ring end gap STD No.1
No.2
Oil
Maximum No.1
No.2
Oil
87.406 ± 87.416 mm (3.4412 ± 3.4416 in.)
87.453 ± 87.467 mm (3.4430 ± 3.4436 in.)
0.084 ± 0.106 mm (0.0033 ± 0.0042)
0.13 mm (0.0051 in.)
0.033 ± 0.059 mm (0.0013 ± 0.0023)
0.08 mm (0.0031 in.)
0.020 ± 0.070 mm (0.0008 ± 0.0028 in.)
0.020 ± 0.060 mm (0.0008 ± 0.0024 in.)
0.25 ± 0.35 mm (0.0098 ± 0.0138 in.)
0.35 ± 0.45 mm (0.0138 ± 0.0177 in.)
0.15 ± 0.40 mm (0.0059 ± 0.0157 in.)
0.95 mm (0.0374 in.)
1.05 mm (0.0413 in.)
1.00 mm (0.0394 in.)

SS0AO±01
± SERVICE SPECIFICATIONSSTARTING (5S±FE)
SS±35
198 Author: Date:
STARTING(5S±FE)
SERVICE DATA
StarterRated voltage and output power
No±load characteristics Current
rpm
Brush length STD
Minimum
Spring installed load STD 1.2 kW
1.4 kW
Minimum 1.2 kW
1.4 kW
Commutator
Diameter STD
Minimum
Undercut depth STD
Minimum
Circle runout Maximum
Magnetic switch
Contact plate for wear Maximum12 V 1.2 kW, 1.4 kW
90 A or less at 11.5 V
3,000 rpm or more
15.5 mm (0.610 in.)
10.0 mm (0.394 in.)
13.7 ± 19.6 N (1.4 ± 2.0 kgf, 3.0 ± 4.4 lbf)
17.6 ± 23.5 N (1.8 ± 2.4 kgf, 3.9 ± 5.3 lbf)
9.8 N (1.0 kgf, 2.2 lbf)
11.8 N (1.2 kgf, 2.6 lbf)
30.0 mm (1.181 in.)
29.0 mm (1.142 in.)
0.6 mm (0.024 in.)
0.2 mm (0.008 in.)
0.05 mm (0.0020 in.)
0.9 mm (0.035 in.)

SS07I±01
± SERVICE SPECIFICATIONSSTARTING (1MZ±FE)
SS±37
200 Author: Date:
STARTING (1MZ±FE)
SERVICE DATA
StarterRated voltage and output power
No±load characteristics Current
rpm
Brush length STD
Minimum
Spring installed load STD
Minimum
Commutator
Diameter STD
Minimum
Undercut depth STD
Minimum
Circle runout Maximum
Magnetic switch
Contact plate for wear Maximum12 V 1.4 kW
90 A or less at 11.5 V
3,000 rpm or more
15.5 mm (0.610 in.)
10.0 mm (0.394 in.)
17.6 ± 23.5 N (1.8 ± 2.4 kgf, 3.9 ± 5.3 lbf)
11.8 N (1.2 kgf, 2.6 lbf)
30.0 mm (1.181 in.)
29.0 mm (1.142 in.)
0.6 mm (0.024 in.)
0.2 mm (0.008 in.)
0.05 mm (0.0020 in.)
0.9 mm (0.035 in.)

SS0AQ±01
± SERVICE SPECIFICATIONSCHARGING (5S±FE)
SS±39
202 Author: Date:
CHARGING(5S±FE)
SERVICE DATA
BatterySpecific gravity (Except maintenance±free battery)
at 20°C (68°F)
Voltage (Maintenance±free battery) at 20°C (68°F)
1.25 ± 1.29
12.5 ± 12.9 V
Drive beltTension w/ A/C New belt
Used belt
w/o A/C New belt
Used belt165 ± 25 lbf
110 ± 10 lbf
125 ± 25 lbf
95 ± 20 lbf
GeneratorRated output
Rotor coil resistance at 20°C (68°F)
Slip ring diameter STD
Minimum
Brush exposed length STD
Minimum12 V 80 A
2.7 ± 3.1 W
14.2 ± 14.4 mm (0.559 ± 0.567 in.)
12.8 mm (0.504 in.)
10.5 mm (0.413 in.)
1.5 mm (0.059 in.)
Voltage
regulatorRegulating voltage13.5 ± 15.1 V

SS07K±01
± SERVICE SPECIFICATIONSCHARGING (1MZ±FE)
SS±41
204 Author: Date:
CHARGING (1MZ±FE)
SERVICE DATA
BatteryVoltage at 20°C (68°F)12.5 ± 12.9 V
Drive belt
Tension
New belt
Used belt
175 ± 5 lbf
115 ± 20 lbf
GeneratorRated output
Rotor coil resistance at 20°C (68°F)
Slip ring diameter STD
Limit
Brush exposed length STD
Limit12 V 80 A
2.1 ± 2.5 W
14.2 ± 14.4 mm (0.559 ± 0.567 in.)
12.8 mm (0.504 in.)
10.5 mm (0.413 in.)
1.5 mm (0.059 in.)
Voltage
regulatorRegulating voltage13.5 ± 15.1 V