2000 SUZUKI SWIFT torque

AIR BAG SYSTEM 10B-1
6F1
6F2
6G
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8A
8B
8C
8D
8E
9
10
10B
SECTION 10B
AIR BAG SYSTEM
CONTENTS
GENERAL DESCRIPTION .............................10B-3
SYSTEM COMPONENTS AND WIRING
LOCATION VIEW AND CONNECTORS..... 10B-4
SYSTEM WIRING DIAGRAM ..................... 10B-5
DIAGNOSIS ....................................................10B-6
DIAGNOSTIC TROUBLE CODE (DTC) ...... 10B-6
USE OF SPECIAL TOOL ............................ 10B-6
INTERMITTENTS AND POOR
CONNECTIONS .......................................... 10B-8
AIR BAG DIAGNOSTIC SYSTEM CHECK . 10B-9
AIR BAG DIAGNOSTIC SYSTEM
CHECK FLOW TABLE .............................. 10B-10
DTC CHECK ............................................. 10B-11
DTC CLEARANCE .................................... 10B-12
DTC TABLE .............................................. 10B-13
TABLE A - “AIR BAG” WARNING LAMP
COMES ON STEADY ............................... 10B-15
TABLE B - “AIR BAG” WARNING LAMP
DOES NOT COME ON ............................. 10B-15
TABLE C - “AIR BAG” WARNING LAMP
FLASHES .................................................. 10B-15
TABLE D - “AIR BAG” WARNING LAMP
CANNOT INDICATE FLASHING
PATTERN OF DTC ................................... 10B-15TABLE E - SDM CANNOT COMMUNICATE
THROUGH THE SERIAL DATA
CIRCUIT ................................................... 10B-21
DTC B1015 - PASSENGER AIR BAG
INITIATOR CIRCUIT RESISTANCE
HIGH ......................................................... 10B-23
DTC B1016 - PASSENGER AIR BAG
INITIATOR CIRCUIT RESISTANCE
LOW .......................................................... 10B-23
DTC B1018 - PASSENGER AIR BAG
INITIATOR CIRCUIT SHORT TO
GROUND .................................................. 10B-23
DTC B1019 - PASSENGER AIR BAG
INITIATOR CIRCUIT SHORT TO
POWER CIRCUIT ..................................... 10B-23
DTC B1021 – DRIVER AIR BAG
INITIATOR CIRCUIT RESISTANCE
HIGH ......................................................... 10B-29
DTC B1022 – DRIVER AIR BAG
INITIATOR CIRCUIT RESISTANCE
LOW .......................................................... 10B-29
DTC B1024 – DRIVER AIR BAG
INITIATOR CIRCUIT SHORT TO
GROUND .................................................. 10B-29 WARNING:
Service on or around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Please observe all WARNINGS and “Service Precautions” under “On-
Vehicle Service” in this section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintended activation of the system or
could render the system inoperative. Either of these two conditions may result in severe injury.
The procedures in this section must be followed in the order listed to disable the air bag system
temporarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures
could result in possible activation of the air bag system, personal injury or otherwise unneeded air
bag system repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were
removed. If a fastener needs to be replaced, use the correct part number fastener for that application.
If the correct part number fastener is not available, a fastener of equal size and strength (or stronger)
may be used. Fasteners that are not reused, and those requiring thread-locking compound, will be
called out. The correct torque value must be used when installing fasteners that require it. If the above
conditions are not followed, parts or system damage could result.

AIR BAG SYSTEM 10B-35
Fig. for STEP 1 and 2
Fig. for STEP 2
Fig. for STEP 3
Tightening torque
(A) : 09932-76010
(B) : 09932-75010
BASE OF
COLUMN
“Q01”
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

10B-48 AIR BAG SYSTEM
3) If equipped with passenger air bag (inflator) module, connect
Yellow connector (1) of passenger air bag (inflator) module,
and be sure to lock connector with lock lever.
a) Connect connector.
b) Lock connector with lock lever.
4) Install glove box.
5) Install “AIR BAG” fuse to fuse box.
6) Turn ignition switch to ON position and verify that “AIR BAG”
warning lamp flashes 6 times and then turns OFF.
If it does not operate as described, perform “AIR BAG DIAG-
NOSTIC SYSTEM CHECK”.
HANDLING AND STORAGE
SDM
Never attempt disassembly of SDM.
When storing SDM, select a place where neither high tem-
perature nor high humidity is anticipated and oil, water and
dust are kept off.
If SDM has been dropped, replace it with a new one.
If installation part of SDM was damaged, repair that part
completely before reinstallation.
All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of
the vehicle to ensure proper operation of the air bag system.
WARNING:
Never power up air bag system when SDM is not rigidly
attached to the vehicle. Otherwise, personal injury may
result.
CAUTION:
After detecting one time of such collision as to meet
deployment conditions, the SDM must not be used. Refer
to “AIR BAG DIAGNOSTIC SYSTEM CHECK” when
checking the SDM.

AIR BAG SYSTEM 10B-57
INSPECTION
Check SDM (3) and SDM plate (5) for dents, cracks or defor-
mation.
Check SDM connector (2) for damage, cracks or lock mech-
anism.
Check SDM terminal for bent, corrosion or rust.
If any faulty condition is found in above checks, replace.
INSTALLATION
For installation, reverse removal procedure, nothing following
points.
Ensure that arrow (4) on the SDM (3) is pointing toward the
front of the vehicle.
Tighten SDM bolts to specified torque.
Tightening torque
SDM mounting bolt (a) : 6 N·m (0.6 kg-m, 4.5 lb-ft)
Connect SDM connector (2) to SDM (3) securely.
Enable air bag system. Refer to “ENABLING AIR BAG SYS-
TEM”. CAUTION:
Do not connect a tester whatever type it may be.
Never repair or disassemble SDM (3).
If SDM has been dropped, or if there are cracks, dents
or other defects in the case or plate, replace it with a
new one.
3
5
2 FORWARD
(a)
3
4
2 FORWARD

AIR BAG SYSTEM 10B-59
INSTALLATION
1) Install passenger air bag (inflator) module (1) to instrument
panel (2).
2) Tighten passenger air bag (inflator) module attaching bolts
to specified torque.
Tightening torque
Passenger air bag (inflator) module mounting bolt
(a) : 23 N·m (2.3 kg-m, 16.5 lb-ft)
3) Connect negative cable to battery.
4) Enable air bag system. Refer to “ENABLING AIR BAG SYS-
TEM”.
DRIVER AIR BAG (INFLATOR) MODULE
Refer to “DRIVER AIR BAG (INFLATOR) MODULE” in SECTION
3C for removal, inspection and installation.
CONTACT COIL AND COMBINATION SWITCH
ASSEMBLY
Refer to “CONTACT COIL AND COMBINATION SWITCH
ASSEMBLY” in SECTION 3C for removal, inspection and installa-
tion.
SEAT BELT PRETENSIONER (IF EQUIPPED)
Refer to “FRONT SEAT BELT WITH PRETENSIONER” in SEC-
TION 10 for removal, inspection and installation.
1
2
(a)