2000 SUBARU LEGACY Owners Manual

11-38
Installing the wheel cover
HGA013BA
Alig n the valve with the valve hole in the c over, t hen fit the c over on
the wheel b y tap p ing your hand evenly around the c i rc umferenc e of
the c over.
NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nutsafter driving approximately 600 miles (1,000 km). If any nut is loose,tighten it to the specified torque.
Aluminum wheels (If equipped)
Aluminum wheels c an b e sc ratc hed and d amag ed easily . Hand le them
c arefully to maintain their ap p earanc e, p erformanc e , and safety.
When any of the wheels is removed and rep lac ed for tire rotation or to
c hang e a flat, always c hec k the tig htness of the wh eel nuts after d riving
ap p roximatly 600 miles (1,000 km). If any nut is lo ose, tig hten it to the
sp ec ified torq ue. Never ap p ly oil to the thread ed p arts, wheel nuts, or tap ered surfac e
of the wheel. Never let the wheel rub ag ainst sharp p rotrusions o r c urb s.
Be sure to fit tire c hains on uniformly and c omp let ely around the tire,
otherwise the c hains may sc ratc h the wheel.

Maintenance and service11-39
–
CONTINUED –

When wheel nuts, b alanc e weig hts, or the c enter c ap rep lac ed , b e
sure to rep lac e them with g enuine SUBARU p arts d esi g ned for aluminum
wheels.
Windshield washer fluid
CAUTION
Never use engine coolant as washer fluid because it could cause paint damage.
Chec k the level of the washer fluid at eac h fuel st op . If the level is low, fill
the fluid up to the nec k of the reservoir.
Use wind shield washer fluid . If wind shield washer f luid is unavailab le use
c lean water.
In areas where water freezes in winter, use an anti -freeze typ e wind shield
washer fluid . SUBARU Wind shield Washer Fluid c ontai ns 58.5% methyl
alc ohol and 41.5% surfac tant, b y volume. Its freezi ng temp erature varies
ac c ord ing to how muc h it is d iluted , as ind ic ated b elow.
Washer Fluid Conc entration
Freezing Temp erature
30% 50%
100%10.4 F ( –12 C)
–4 F ( –20 C)
–49 F ( –45 C)
HBB004IA

11-40Replacement of windshield wiper blades
Grease, wax, insec ts, or other materials on the win
d shield or the wip er
b lad e results in jerky wip er op eration and streakin g on the g lass. If you
c annot remove the streaks after op erating the wind s hield washer or if the
wip er op eration is jerky, c lean the outer surfac e o f the wind shield (or rear
wind ow) and the wip er b lad es using a sp ong e or soft c loth with a neutral
d eterg ent or mild -ab rasive c leaner. After c leaning , rinse the wind shield
and wip er b lad es with c lean water. The wind shield i s c lean if b ead s d o
not form when you rinse the wind shield with water.
CAUTION
Do not clean the wiper blades with gasoline or a solvent, such as
paint thinner or benzene. This will cause deterioration of thewiper blades.
If you c annot eliminate the streaking even after fo llowing this method ,
rep lac e the wip er b lad es using the following p roc ed ures:
1. Raise the wip er arm off the wind shield .
2. Remove the wip er b lad e assemb ly b y hold ing its p i vot area and p ush-
ing it in the d irec tion shown b y the arrow while d e p ressing the wip er
b lad e stop p er.
HS0190
Stopper
3. Grasp the loc ked end of the b lad e rub b er assemb ly and p ull it firmly
until the stop p ers on the rub b er are free of the me tal sup p ort.

Maintenance and service11-41
–
CONTINUED –
HS0191
Metal support
4. If the new b lad e rub b er is not p rovid ed with two metal sp ines, remove
the metal sp ines from the old b lad e rub b er and inst all them in the new
b lad e rub b er.
HS0192
Metal spines
5. Alig n the c laws of the metal sup p ort with the g ro oves in the rub b er
and slid e the b lad e rub b er assemb ly into the metal sup p ort until it loc ks.
Be sure to p osition the c laws at the end of the met al sup p ort b etween the
stop p ers on the rub b er as shown. If the rub b er is n ot retained p rop erly,
the wip er b lad e may sc ratc h the wind shield .

11-42
HS0194
HS0193
Stopper
6. Install the wip er b lad e assemb ly to the wip er arm . Make sure that it
loc ks in p lac e.
7. Lower the wip er arm. Battery
WARNING
Before beginning work on or near any battery, be sure to extin-
guish all cigarettes, matches, and lighters. Never expose a bat- tery to an open flame or electric sparks. Batteries give off a gaswhich is highly flammable and explosive. For safety, in case an explosion does occur, wear eye protec-
tion or shield your eyes when working near any battery. Never
lean over a battery. Do not let battery fluid contact eyes, skin, fabrics, or paint be-
cause battery fluid is a corrosive acid. If battery fluid gets on yourskin or in your eyes, immediately flush the area with water thor-
oughly. Seek medical help immediately if acid has entered theeyes.If battery fluid is accidentally swallowed, immediately drink a
large amount of milk or water, and seek medical attention
immediately. To lessen the risk of sparks, remove rings, metal watchbands,

Maintenance and service11-43
–
CONTINUED –
and other metal jewelry. Never allow metal tools to contact the
positive battery terminal and anything connected to it WHILE youare at the same time in contact with any other metallic portion ofthe vehicle because a short circuit will result.
Keep everyone including children away from the battery.
Charge the battery in a well-ventilated area.
CAUTION
Never use more than 10 amperes when charging the battery be-
cause it will shorten battery life.
It is unnec essary to p eriod ic ally c hec k the b attery fluid level or p eriod i-
c ally refill with d istilled water. Fuses
CAUTION
Never replace a fuse with one having a higher rating or with mate-
rial other than a fuse because serious damage or a fire could re-sult.
HBB008CBHB8003CA
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in

11-44two fuse b oxes. The one is loc ated und er the instru
ment p anel b ehind
the c oin tray on the d river ’s seat sid e. The other one is housed in the
eng ine c omp artment. The fuse p uller and sp are fuses are stored in the
main fuse b ox c over in the eng ine c omp artment.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.
HS0208
HS0204
Good
BlownFuse puller
Spare fuses
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec tri-
c al ac c essories.
2. Remove the c over.
(For b ehind the c oin tray: op en the c oin tray and p ull it horizontally to
remove it.)
3. Determine whic h fuse may b e b lown. The b ac k sid e of eac h fuse b ox
c over and the “Fuse and c irc uits ” sec tion in c hap ter 12 in this manual
show the c irc uit for eac h fuse.
HS0207
Fuse puller

Maintenance and service11-45
–
CONTINUED –
4. Pull out the fuse with the fuse p uller.
5. Insp ec t the fuse. If it has b lown, rep lac e it wit
h a sp are fuse of the
same rating .
6. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs.
Main fuse and fusible link
HB8003CB
The main fuses and fusib le link are d esig ned to mel t d uring an overload
to p revent d amag e to the wiring harness and elec tri c al eq uip ment.
Chec k the main fuses and fusib le link if any elec tr ic al c omp onent fails to
op erate (exc ep t the starter motor) and other fuses are g ood . A melted
main fuse or fusib le link must b e rep lac ed . Use onl y rep lac ements with
the same sp ec ified rating as the melted main fuse o r fusib le link. If a
main fuse or fusib le link b lows after it is rep lac e d , have the elec tric al sys-
tem c hec ked b y your nearest SUBARU d ealer.
Installation of accessories
Always c onsult your SUBARU d ealer b efore installing fog lig hts or any
other elec tric al eq uip ment in your vehic le. Suc h ac c essories may c ause
the elec tronic system to malfunc tion if they are in c orrec tly installed or if
they are not suited for the vehic le.