2000 LEXUS GS400 lock

I04028

Engine Room No.3 Relay Block
Relays
A. FAN NO.1 Relay
B. FAN NO.2 Relay
C. A/C COMP Relay
D. FAN NO.3 Relay

Engine Room No.2 Relay Block
Relays
A. Horn Relay
B. ABS SOL Relay
C. TRC MTR Relay
D. ABS MTR Relay
I04027
I04028
A
B
C
D
EE. Headlight Dimmer
(Daytime Running Light No.2) Relay
A
B
C
DFuses
1. H±LP R UPR Fuse
(w/ Daytime Running Light System)
2 H±LP L UPR Fuse
(w/ Daytime Running Light System) 12 BE±18
± BODY ELECTRICALPOWER SOURCE
2319 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04029
Fuses
Relays 1. AM1 H±Fuse
2. WASHER Fuse
3. FOG Fuse
4. TAIL Fuse
B. Taillight Control Relay A. Fog Light Relay
C. Body ECU No.2
Driver Side Instrument Panel Junction Block
5. SRS±ACC Fuse
6. GAUGE Fuse
7. FUEL OPN Fuse
8. D FR DOOR Fuse
9. PANEL Fuse
10. HTR Fuse
11. SRS±B Fuse
12. P/SEAT (D) Fuse
13. RAD NO.2 Fuse
14. WIP Fuse
15. OBD Fuse
16. STOP Fuse
17. CIG Fuse
18. ECU±IG Fuse
19. STARTER Fuse
20. IGN Fuse
21. D FR DOOR Fuse
2
21 34 5
678 9
10 11 12 13
14 15 16 17
18 19 20AB
C 1
± BODY ELECTRICALPOWER SOURCE
BE±19
2320 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04030
Fuses
Relays 1. DEF H±Fuse
2. ±
3. ±
4. MIR HTR Fuse
A. Ignition Main Relay
B. Mirror Heater Relay
E. Body ECU No.1
Passenger Side Instrument Panel Junction Block
5. ±
6. ±
7. S/ROOF Fuse
8. P FR DOOR Fuse
9. ±
10. ±
11 .
12. P/SEAT (P) Fuse
13. DOME Fuse
14. SEAT HTR Fuse
15. ±
16. TV Fuse
17. ECU±B2 Fuse
18. ±
19. ±
20. ±
21. P FR DOOR Fuse
2
21 34 5
67 8 9
10 11 12 13
14 15 16 17
18 19 20AB
E
C. Defogger Relay
D. Heater Relay
CD
1
BE±20
± BODY ELECTRICALPOWER SOURCE
2321 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE0GP±09
I04154
I04155
I04156
Terminal
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±161
2462 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REPLACEMENT
1. REPLACE TRANSMITTER (LITHIUM) BATTERY
NOTICE:
Special caution should be taken for handling each compo-
nent as they are precision electronic components.
(a) Using a screwdriver, remove the screw and cover.
NOTICE:
Do not pry out the cover forcibly.
HINT:
Push the cover with a finger as shown in the illustration, so that
there becomes clearance, then pry out the cover from that
clearance.
(b) Remove the transmitter.
(c) Using a screwdriver, remove the 2 screws and cover.
(d) Remove the battery (lithium battery).
NOTICE:
Do not push the terminals with a finger.
If prying up the battery (lithium battery) forcibly to re-
move, the terminals are deformed.
(e) Install a battery (lithium battery) as shown in the illustra-
tion.
NOTICE:
Face the battery upward. Take care not to deform the termi-
nals.
(f) Check that O±ring is not distorted or slipped off, and
install the cover.
(g) Using a screwdriver, tighten the 2 screws.
NOTICE:
When the shrews are tightened loosely, it might cause
faulty contact of battery (lithium battery) and terminals.
(h) Assemble the transmitter to the key plate and the cover.
(i) Using a screwdriver, tighten the screw.

BE±162
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2463 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. REPLACE DOOR CONTROL RECEIVER AND TRANS-
MITTER
NOTICE:
When replacing the door control receiver and transmitter,
registration of recongnition code is necessary because
they are provided as single components.
(a) Select which operation mode should be performed from
the following modes.
Add mode
Rewrite mode
Prohibition mode
Confirmation mode
HINT:
The add mode is used to retain codes already registered
while you register new recongnition codes. This mode is
used when adding a transmitter. However, if the number
of registered codes exceeds 4 codes, previously regis-
tered codes are correspondingly erased in order, starting
from the first registered code.
The rewrite mode is used to erase all previously regis-
tered codes and register only new recognition codes.
The prohibition mode is used to erase all registered codes
and cancels the wireless door lock function. Use this
mode when the transmitter is lost.
The confirmation mode is for confirming how many re-
congnition codes are already registered before you regis-
ter additional recognition codes.
(b) Follow the chart on the following pages to register the
transmitter recongnition code at the wireless door lock
conrol receiver.
HINT:
When procedure is out of the specified, the operation re-
turns to normal operation.
Maximum 4 recognition codes can be registered.

± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±163
2464 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
Start registration of recognition code
The vehicle should be in the following conditions.

Any door is OPEN. (Other doors are CLOSED)

Any door is UNLOCKED.

Insert the key into the ignition key cylinder, then pull it out.
Press the door lock control switch (for manual operation) 5 times to
LOCK/UNLOCK at approx. 1 sec. interval.
1st time 2nd time 3rd time 4th time 5th time
LOCK
OFF
UNLOCK
Approx.
1 sec.Approx.
1 sec.
Close the all door, then open the any door.
Again press the door lock control switch (for manual operation) 5 times to
LOCK/UNLOCK at approx. 1 sec. interval.
1st time 2nd time 3rd time 4th time 5th time
LOCK
OFF
UNLOCK
Approx.
1 sec.Approx.
1 sec.
Insert the key into the ignition key cylinder.
Within
40 secs.
Within
40 secs.

BE±164
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2465 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
Within
3 secs.
Turn the ignition switch from ON to LOCK at approx. 1 sec. interval 1 to 5 times to select the mode.
Pull out the key plate from the ignition key cylinder.
When add mode or rewrite mode
is selected.When confirmation
mode is selected.
ON
ONON
LOCK
LOCKLOCK
Approx.
1 sec.Approx.
1 sec. Approx. 1 sec.Approx.
1 sec.Approx.
1 sec.
Add mode
Rewrite modeConfirmation mode
ON ± LOCK change occurs 1 time
ON ± LOCK change occurs 2 timesON ± LOCK change occurs 3 times
MPX body ECU automatically performs
the LOCK±UNLOCK operation once
or twice at 1 sec. interval to iniform the
operator that either the add mode or
rewrite mode has been selected.
LOCK±UNLOCK occurs once
LOCK±UNLOCK occurs twice
Indicates that add mode has been selected.
Indicates that rewrite mode has been
selected.
1 sec.
LOCK
1 sec.1 sec.
LOCK
UNLOCK
UNLOCK
LOCK
2 secs.2 secs.
UNLOCK MPX body ECU automatically performs the
LOCK±UNLOCK operation 1 to 4 times at
2 sec. interval to inform the operator of
the number of the registered codes.
HINT:
When the number of the registered code
is 0, the operation is automatically
performed 5 times.
Example:
When the operation is performed twice, it
directs that 2 types of recognition code
have been registered.
1st time 2nd time
Registration of recognition code (Confirmation
mode and prohibition mode) is completed.
ON
LOCK
Approx.
1 sec.Approx.
1 sec.
Prohibition mode
ON ± LOCK change occurs 5 times
When prohibition
mode is selected.

± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±165
2466 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
MPX body performs LOCK±UNLOCK operation 5 times at a 1 sec.
interval to inform the operator that prohibition mode has been selected.
Press again either one of 3 switches on the transmitter for more than 1 sec.
MPX body ECU automatically performs LOCK±UNLOCK operation once or
twice at a 1 sec. interval to inform the operator that the receiver has received the
signal from the transmitter.
LOCK±UNLOCK occurs once
LOCK±UNLOCK occurs twice Registration of recognition code is completed
Registration of recognition code has not been completed.

Recognition code received first time and second time did not match.
Proceed to continue registration
If even one of the following conditions is satisfied, registration of recognition
codes is completed.

40 secs. elapses since the MPX body ECU response.

The driver's door is closed.

The key plate is inserted in the ignition key cylinder.

4 type recognition codes are registration at one time.
Registration of recognition codes (add mode or rewrite mode) is completed.
Within
3 secs.Within
40 secs.
ON
LOCK
Approx.
1 sec.Approx.
1 sec.
When prohibition
mode is selected.
Press the lock and unlock switches on the transmitter simultaneously within 1 sec.
If LOCK±UNLOCK operation can not be performed at all, the mode returns to the
normal mode, then start with ºStart registration of recognition codeº.
Proceed to finish registration
Within 40 secs.