2000 LEXUS GS400 fuel pump

A11125
Throttle Body and Intake Air Connector AssemblyWater Bypass Hose
PCV Hose
EVAP Hose
 Gasket
Air Assist Hose
Vacuum
Hose
PS Air Hose
Air Intake Chamber
Engine Wire
Clamp
Drive Belt
TensionerClamp Bracket
Ground StrapFuel Pressure
Pulsation Damper Clamp Bracket
Water Bypass
Outlet
No.1 Water Bypass Pipe
No.3 Timing Belt Cover O±Ring
Oil Filler CapFuel Inlet Pipe
PS Air Hose
Hose
Clamp
Timing Belt
Tensioner
PS Pump Stay
Oil Dipstick
and Guide
for A/T
PS Vane Pump Water Bypass Hose
28 (280, 21)
Engine Wire
 O±Ring
No.2 Timing Belt Cover
GasketGasket
21 (210, 15)
32.5 (325, 24)
 Gasket
 Gasket
Engine Wire
Clamp
 O±Ring  O±RingOil Dipstick and
Guide for Engine
27 (270, 20)
58 (590, 43)39.2 (400, 29)N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable Part
Dust BootEngine Wire
Clamp
No.2 Vacuum Pipe
Hose Clamp
Vacuum Control
Valve Set
EM±30
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
1384 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

A02732
(a)
(b) (c)
(d)(d)
(c) (b)
A02811
A02733
Clamp Bracket
A11123
5 mm
Hexagon
Wrench
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±35
1389 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
20. DISCONNECT ENGINE WIRE FROM CYLINDER HEAD
(a) Disconnect the ground strap from the cylinder head.
(b) Disconnect the 2 water bypass hoses from the hose
clamps on the cylinder head and oil filter bracket.
(c) Remove the 2 bolts and hose clamps.
(d) Disconnect the heated oxygen sensor (bank 2 sensor 1)
connector and engine wire clamp from the hose clamps.
(e) Disconnect the heated oxygen sensor (bank 1 sensor 1)
connector.
(f) Disconnect the crankshaft position sensor connector.
(g) Disconnect the generator connector.
(h) Remove the bolt and clamp bracket, and disconnect the
engine wire from the water pump.
(i) Disconnect the 2 ground terminals from the intake man-
ifold.
(j) Disconnect the 2 engine wire clamps from the No.1 oil
pipe and clamp bracket on the intake manifold.
(k) Remove the bolt and clamp bracket.
(l) Disconnect the ECT sensor connector.
(m) Remove the 2 knock sensor connectors.
(n) Remove the oil pressure switch connector.
(o) Remove the oil level sensor connector.
(p) Remove the starter connector.
(q) Remove the 6 injector connectors.
(r) Remove the camshaft timing oil control valve connector.
(s) Remove the camshaft position sensor connector.
(t) Using a 5 mm hexagon wrench, remove the bolt holding
the engine wire protector to the No.2 cylinder head cover.
(u) Remove the 3 nuts, and disconnect the engine wire pro-
tector from the intake manifold.
21. REMOVE FUEL PRESSURE PULSATION DAMPER
(See page SF±26)

A09753
Transmission Control Rod
13 (130, 9)
13 (130, 9)
Rear Engine Mounting Member
Fuel Inlet
 Gasket
29 (300, 22)
13.5 (135, 10)25.5 (260, 19)
70 (714, 52)
Hole Plug PS Vane Pump Assembly
PS Pump Rear Stay57.9 (590, 43)
39.2 (400, 29)
65 (660, 48)
65 (660, 48)
35 (360, 26)
26 (265, 19)
52 (530, 38)
57.9 (590, 43)
A/C Compressor
52 (530, 38)
52 (530, 38)
Adjusting Washer
PS Gear Housing
Propeller Shaft
79 (805, 58)
37 (375, 27)
Heat Insulator
Heat Insulator
Adjusting Nut
69 (700, 51)
79 (805, 58)
44 (440, 32)
 Gasket Gasket
Ring
Ring
Center Exhaust Pipe
Front Floor Center Brace
 Gasket
Front Exhaust Pipe
(with Rear TWC)
44 (440, 32)
 Gasket
45 (450, 32)
Heated Oxygen Sensor
(Bank 2 Sensor 2)
44 (440, 32)
N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable part
44 (440, 32)Pipe Support
Bracket
Hose
EM±60
± ENGINE MECHANICAL (2JZ±GE)ENGINE UNIT
1414 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

EM0DJ±03
A02768
N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable part

Precoated partRH Engine Mounting Bracket and Insulator Assembly
No.2 Water Bypass Pipe with Hose
 Gasket
Water Pump

Engine Coolant Drain Plug
 O±Ring
21 (210, 15)
 O±Ring O±RingKnock Sensor 1
Knock Sensor 2
GeneratorFuel Inlet Pipe
Oil Pump
 Crankshaft Front Oil Seal
Oil Filter and
Bracket AssemblyNo.1 Oil Pipe
Union Bolt
55 (550, 41) Gasket
90 (900, 66)Union Bolt

Oil Pressure Switch
 Gasket21 (210, 15)
x 9
 O±Ring
x 6
x 6x 16
 Gasket
No.1 Oil Pan
Oil Pan Baffle Plate
Oil Strainer
LH Engine Mounting Bracket
and Insulator Assembly
 Gasket
x 16
No.2 Oil Pan
x 6
Drain Plug
EM±74
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1428 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CYLINDER BLOCK
COMPONENTS

EM0DK±03
P02447
EM±76
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
1430 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
DISASSEMBLY
1. INSTALL ENGINE TO ENGINE STAND FOR
DISASSEMBLY
2. REMOVE GENERATOR
Remove the bolt, nut, pipe bracket and generator.
3. REMOVE TIMING BELT AND PULLEYS
(See page EM±16)
4. REMOVE NO.2 WATER BYPASS PIPE WITH HOSE
Remove the bolt, 2 nuts, No.2 water bypass pipe and gasket.
5. REMOVE WATER PUMP
Remove the 6 bolts, water pump and O±ring.
6. REMOVE CYLINDER HEAD (See page EM±33)
7. REMOVE OIL PRESSURE SWITCH AND KNOCK
SENSORS
Using SST, remove the switch and sensors.
SST 09816±30010
8. REMOVE OIL FILTER AND BRACKET ASSEMBLY
(a) Remove the union bolt and oil filter bracket.
(b) Remove the gasket from the union bolt.
(c) Remove the O±ring from the oil filter bracket.
9. REMOVE NO.1 OIL PIPE
Remove the union bolt, No.1 oil pipe and 2 gaskets.
10. REMOVE FUEL INLET PIPE
Remove the 2 bolts and fuel inlet pipe.
11. REMOVE LH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
12. REMOVE RH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Remove the 4 bolts and mounting bracket.
13. REMOVE OIL PUMP (See page LU±6)
14. REMOVE REAR OIL SEAL RETAINER
(a) Remove the 6 bolts of the retainer.
(b) Remove the oil seal retainer by prying the area between
the oil seal retainer and main bearing cap with a screw-
driver.

P02420
Painted Mark
90°90°
P02197
Seal Width
2 ± 3 mm
Seal
Packing
± ENGINE MECHANICAL (2JZ±GE)CYLINDER BLOCK
EM±95
1449 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Mark the front of the connecting rod cap bolt with paint.
(d) Retighten the connecting rod cap bolts 90° in the numeri-
cal order shown.
(e) Check that the painted mark is now at a 90° angle to the
front.
(f) Check that the crankshaft turns smoothly.
13. CHECK CONNECTING ROD THRUST CLEARANCE
(See page EM±76)
14. INSTALL REAR OIL SEAL RETAINER
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the retainer
and cylinder block.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.

Thoroughly clean all components to remove all de-
bris.

Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the retainer as shown in the illustra-
tion.
Seal packing: Part No.08826±00080 or equivalent

Install a nozzle that has been cut to a 2 ± 3 mm (0.08
± 0.12 in.) opening.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the retainer with the 6 bolts.
Torque: 6.0 N´m (60 kgf´cm, 53 in.´lbf)
15. INSTALL OIL PUMP (See page LU±12)
16. INSTALL RH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Install the mounting bracket with the 4 bolts.
Torque: 59 N´m (590 kgf´cm, 44 ft´lbf)
17. INSTALL LH ENGINE MOUNTING BRACKET AND
INSULATOR ASSEMBLY
Install the mounting bracket with the 4 bolts.
Torque: 59 N´m (590 kgf´cm, 44 ft´lbf)
18. INSTALL FUEL INLET PIPE
Install the fuel inlet pipe with the 2 bolts.
Torque: 29 N´m (290 kgf´cm, 21 ft´lbf)
19. INSTALL NO.1 OIL PIPE
Install the No.1 oil pipe with 2 new gaskets and the union bolt.
Torque: 55 N´m (550 kgf´cm, 41 ft´lbf)

IN±28± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
28 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. PROBLEM SYMPTOMS TABLE
The suspected circuits or parts for each problem symptom are shown in the table below. Use this table to
troubleshoot the problem when a ºNormalº code is displayed in the diagnostic trouble code check but the
problem is still occurring. Numbers in the table indicate the inspection order in which the circuits or parts
should be checked.
HINT:
When the problem is not detected by the diagnostic system even though the problem symptom is present,
it is considered that the problem is occurring outside the detection range of the diagnostic system, or that
the problem is occurring in a system other than the diagnostic system.
Symptom
Suspect AreaSee page
Engine does not crank (Does not start)
No initial combustion (Does not start)
No complete combustion (Does not start)1. Starter and starter relay
1. ECM power source circuit
2. Fuel pump control circuit
3. Engine control module (ECM)
1. Starter signal circuit
2. Fuel pump control circuit1. Fuel pump control circuitDI±147
DI±151
IN±29
PROBLEM SYMPTOMS TABLE
1. Compression
2. Fuel pump control circuit 1. A/C signal circuit
2. Fuel pump control circuit 1. A/C signal circuit (Compressor circuit)
2. ECM power source circuit 1. Starter signal circuit
2. Fuel pump control circuit1. Starter signal circuit
2. Fuel pump control circuit
3. Compression
idling) High engine idle speed (Poor idling) Hot engine Cold engine (Difficult to start)Engine cranks normally (Difficult to start)
AC±88 DI±144
DI±151
EM±3 DI±151

Problem Symptom
Page
Indicates the page where the flow chart for each circuit
is located.

Circuit Inspection, Inspection Order
Indicates the circuit which needs to be checked for each problem
symptom. Check in the order indicated by the numbers.

Circuit or Part Name
Indicates the circuit or part which needs to be checked.
ST±2
ST±17
DI±144
DI±151
DI±144
DI±151

± INTRODUCTIONTERMS
IN±37
37 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) CW
Curb Weight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro±Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR±VMEgr±Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E±VRVElectric Vacuum Regulating Valve
EXHExhaust
FEFuel Economy
FFFront±Engine Front±Wheel±Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront±Engine Rear±Wheel±Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront±Wheel±Drive
GASGasoline
GNDGround
HACHigh Altitude Compensator
H/BHatchback