1999 TOYOTA CAMRY change time

Toyota Supports ASE CertificationPage 1 of 1
EG009±99
Title:
M.I.L. ON" DTC P1133
Models:
'97±'99 Camry and '99 Solara: 5S±FE CA Spec.
Technical Service
BULLETIN
October 1, 1999

Under certain driving conditions, some 5S±FE equipped 1997±1999 Camry and 1999
Solara California emission specification vehicles may exhibit a M.I.L. ªONº DTC P1133.
An improved Air Fuel Ratio Sensor has been developed to correct this condition.
1997 ± 1999 Camry & 1999 Solara (5S±FE) with California emission
specification.
MODEL YEARORIGINENGINESTARTING VIN
JPNJT2BG2#K*X0363615
1999 Camry
NAP(5S±FE)4T1BG2#K*XU603913
4T1BG2#K*XU918675
2000 Solara±±
* # May be a 2 or an 8.
* * May be any number from 0 to 9 or an X.
PREVIOUS PART NUMERCURRENT PART NUMBERPART NAME
89467±3301089467±33011Sensor, Air Fuel
Should a M.I.L. ªONº condition with DTC P1133 be encountered, perform diagnostic
procedures as described in the Repair Manual.
If the problem source cannot be identified after checking all affected areas according
to the Repair Manual, the cause may be an Air/Fuel Ratio Sensor malfunction. In this
case, replace the Air/Fuel Ratio Sensor with the updated part.
If the Exhaust Manifold threads are damaged by removal of the sensor, they can be
repaired by the proper use of a M18 x 1.5 tap.
OPCODEDESCRIPTIONTIMEOPNT1T2
EL9006Sensor, Air Fuel Ratio0.389467±330109999
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
Coverage is extended to 36 months or 50,000 miles, which ever occurs first, in the
states of California and Massachusetts due to state emissions warranty legislation.
NOTE:
Please enter the DTC in the condition/Cause/Remedy section when applying for
warranty reimbursement.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
ENGINE
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Repair
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
NV007±00Title:
DOOR MIRROR WIND NOISE
Models:
'97 ± '99 Camry
Technical Service
BULLETIN
March 31, 2000

TSB Update Notice:
The information contained in this TSB updates The information contained in this TSB
updates BO019±99 dated December 3, 1999. Revised text is red
and underlined.
Wind/road noise heard around the door mirrors of some Japan produced Camry vehicles
may be caused by an improperly positioned mirror wire harness grommet and/or harness
connector.
1997 through 1999 Camry vehicles. (Japan produced only)
PLANTSTARTING VIN
TMC
JT2BG22K * X0367325
JT2BG28K * X0367352
JT2BF22K * X0227381
JT2BF28K * X0227306
OP CODEDESCRIPTIONTIMEOPNT1T2
BD0009Adjust the Wire Harness Grommet
and/or Connector0.487940±XXXXX±XX (LH)
87910±XXXXX±XX (RH)5957
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
1. Carefully pry off the door speaker
cover and remove the nut using a 10
mm socket that secures the speaker
to the door.
2. Look through the door mirror harness
access hole and check the position of
the wire harness grommet and wire
harness connector ± the harness
connector should be inside the
grommet and the grommet should be
fully seated in the mirror housing.
NVH
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information
Repair
Procedure
Connector
Grommet
CORRECT POSITIONConnector
and Grommet
Mirror Housing
Speaker

Toyota Supports ASE CertificationPage 1 of 1
PA004±99Title:
TWO-TONE PAINT COLOR
Models:
'99 Camry Limited Edition
Technical Service
BULLETIN
June 11, 1999

The following information outlines the two±tone painting scheme on 1999 Camry Limited
Edition.
1999 Camry Limited Edition
COLOR NO.COMBINATIONTWO±TONE NAMES
2GP4M7/1B2Oyster Pearl/Antique Sage
Pearl accent
28Y051/4M7Diamond White Pearl/
Oyster Pearl Accent
OPCODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
PAINT
Introduction
Affected
Vehicles
Production
Change
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 3
PG006±03
Title:
WARRANTY PARTS
MARKING PROCEDURE
Models:
All Models
Technical Service
BULLETIN
September 26, 2003
Effective September 1, 2003, all warranty parts (as indicated on the next page) must be
marked in the area or location of the failure. The technician should complete this
procedure after the failed part has been removed from the vehicle and before the part is
placed in the 10±bin storage. (Exchanged parts and remanufactured parts are not
included in this procedure.)
Failed parts marking will be beneficial in detecting and resolving product and parts quality
issues. This will also offer additional opportunities to make future enhancements to our
parts and products.
Parts are subject to random inspection in the dealership by field representatives to
ensure compliance with this new policy.
Failure to comply with this policy may result in a debit of the corresponding
warranty claim(s).
All models.
All technicians must follow these procedures to ensure proper parts marking:
Wipe the part clean (no excess fluid should be present).
Indicate area of defect or failure by marking the specific part(s) with a water
resistant permanent marker. Use a color that can be easily seen against the
background of the part being marked. For dark surfaces the color yellow is highly
recommended as well as the color black for light surfaces.
Mark the area of failure or defect by drawing a circle, a square, pointing an arrow
or adhering tape with an indication of the failed or defect location.
Attach a completed Warranty Parts Tag (M/N 00404±PRETN±TAGS) to the
marked part.
All other parts recovery/shipping policies and procedures apply
.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRODUCT GENERAL INFORMATION
Introduction
Applicable
Vehicles
Parts
Marking
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
PG008-02Title:
REPLACEMENT CERTIFICATION LABELS
Models:
All Models
Technical Service
BULLETIN
January 18, 2002

TSB UPDATE NOTICE:
The information contained in this TSB updates PG006±01 dated May 4, 2001.
Revised text is red
and underlined. The changes will take place February 1, 2002.
Replacement Certification Labels (vinyl label affixed to driver's door or door post)
may be available from Toyota providing the request meets one of the criteria
listed below.
Certification Label Location
MFD.BY: TOYOTA MOTOR MANUFACTURING
CANADA INC. 10/01
GVWR 3935LB GAWR FR 1970LB RR 1985LB
THIS VEHICLE CONFORMS TO ALL APPLICABLE
FEDERAL MOTOR VEHICLE SAFETY, BUMPER, AND
THEFT PREVENTION STANDARDS IN EFFECT ON
THE DATE OF MANUFACTURE SHOWN ABOVE.
XT0XX00X0X000000 PASS.CAR
C/TR:3L5/FB14 MODEL:ZZE134L ± DHPNKA
A/TM:±04A/U341F MADE IN CANADA
S26 AA01904759
All Toyota vehicles.
1. The vehicle is in an accident and the label is damaged or is attached to a part that will
be replaced during the repair.
NOTE:
Processing a new label
will be delayed significantly if the original certification label
is not available.
A replacement label MAY NOT be available if the vehicle is more than 5 years old
and the old label does not accompany this request.
2. The label is stolen.
To request a replacement label, complete a copy of the form on the back of this bulletin.
Your dealer parts account will be billed $25.00
for each replacement of a damaged or
stolen label.
NOTE:
All replacement labels for damaged and/or stolen vehicles are subject to approval by
the Technical Compliance Department. If you have any specific questions, contact
(310) 468±3390.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
PRODUCT GENERAL INFORMATION
Introduction
Applicable
Vehicles
Certification
Label Criteria
Procurement
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
PG009-02Title:
REPLACEMENT VIN PLATES
Models:
All Models
Technical Service
BULLETIN
January 18, 2002

TSB UPDATE NOTICE:
The information contained in this TSB updates PG007±01 dated May 4, 2001.
Revised text is red
and underlined. The changes will take place February 1, 2002.
Replacement VIN plates (metal plates riveted to dashboard) may be available from
Toyota providing the request meets the criteria listed below.
VIN Plate Location
All Toyota vehicles.
The vehicle is in an accident and the plate is damaged.
NOTE:
The original plate to be replaced MUST accompany the request.
NOTE:
If a plate is stolen, be sure to contact the State Police or your State's Department of
Motor Vehicles (DMV). In most cases the State DMV will issue a unique number so that
the original number can be included on stolen vehicle listings. If this is the case, a
replacement plate is NOT available from Toyota. However, the original VIN, NOT the
state issued VIN, must be used on all warranty claims.
To request a replacement plate, complete a copy of the form on the back of this page.
Note that the damaged VIN plate MUST accompany the request form. Your dealer parts
account will be billed $25.00
for each replacement of a damaged plate.
NOTE:
All replacement plates for damaged and/or stolen vehicles are subject to approval by
the Technical Compliance Department. If you have any specific questions, contact
(310) 468±3390.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
PRODUCT GENERAL INFORMATION
Introduction
Applicable
Vehicles
Replacement
VIN Plate
Criteria
Procurement
Procedure
Warranty
Information

Page 1 of 1Toyota Supports ASE Certification
ST002±00Title:
STEERING WHEEL NUT
Models:
'94 ± '00 Camry
Technical Service
BULLETIN
May 12, 2000

The steering wheel installation nut torque specification has been changed. Please update
the repair manuals for the applicable vehicles.
1994 ± 2000 model year Camry
50 N m (510 kgf cm, 37 ft lbf)
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
STEERING
Introduction
Applicable
Vehicles
Warranty
Information

Page 1 of 1Toyota Supports ASE Certification
ST004±00Title:
STEERING RACK END NOISE
Models:
'97 ± '00 Camry (NAP) & '99 ± '00 Solara
Technical Service
BULLETIN
June 16, 2000

Some 1997 ± 2000 model year Camry (NAP) and 1999 ± 2000 Solara vehicles may
experience a squeaking noise from the front suspension. To improve this condition,
production parts have been changed.
1997 ± 2000 model year Camry (North American Produced)
1999 ± 2000 model year Solara
MODELSTARTING VIN
NAP Camry
4T1BG2*K*YU668756
4T1BG2*K*YU986504
4T1BF2*K*YU104860
4T1BF2*K*YU947590
Solara2T1C*2*P*YC359722
MODELPREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
Camry
and
Solara
45503±09030
or
45503±39055
or
45503±39135
45503±39135Steering Rack End
Sub±Assembly
HINT:
A quick reference in differentiating
between the previous and new parts is
that the previous Rack End Shaft is
BLACK and the current part is GRAY.Previous Part (BLACK SHAFT)
Current Part (GRAY SHAFT)
OP CODEDESCRIPTIONTIMEOPNT1T2
444631R & R Power Steering Rack End
Sub±Assembly (One Side)2.2
45503±09030
or
45503±39055
9199
Combo Code AOther Side0.5
45503 39055
or
45503±39135
9199
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
STEERING
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information