1999 Lexus ES300 Owner's Manuals (in English)

INTERIOR EQUIPMENT
77
14E007±1

Front cigarette lighter and ashtray
To use the cigarette lighter and ashtray, first push
against the ashtray cover. Then when the ashtray
opens out, press in the cigarette lighter. When it
becomes heated, it automatically pops out ready for
use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in
the ºACCº position.
When fini shed with your cigarette, thoroughly extinguish
it in the ashtray to prevent other cigarette butts from
catching fire. After using the ashtray, push it back in
completely.
To remove the ashtray, just pull it up.
Use a Lexus genuine cigarette lighter or equivalent for
replacement.

INTERIOR EQUIPMENT
78
14E008±4

Rear ashtray 1Snuffer bridge
To use the ashtray, pull on the lid.
When finished with your cigarette, thoroughly extinguish
it in the ashtray to prevent other cigarette butts from
catching fire. After using the ashtray, close the lid
completely.
To remove the ashtray, pull it out while pressing on the
snuffer bridge to release the catch.
CAUTION
To reduce the chance of injury in case of an accident or
sudden stop while driving, always close the ashtray
completely after using.

INTERIOR EQUIPMENT
79
POWER OUTLET
14E016

INTERIOR EQUIPMENT
80The power outlet is designed for power supply for
car accessories.
The ignition key must be in the ºACCº or ºONº position
for the power outlet to be used.
NOTICE
To prevent the fuse from being blown, do not
use the electricity over the total vehiclecapacity of 12V/120W.
To prevent the battery from being discharged,do not use the power outlet longer thannecessary when the engine is not running.
Close the power outlet lid when the poweroutlet is not in use. Inserting a foreign objectother than the appropriate plug that fits theoutlet, or allowing any liquid into the outlet maycause electrical failure or short circuits.

INTERIOR EQUIPMENT
81
GLOVEBOX
14E0039

1Unlock 2Open 3Lock
To open the glovebox door, pull the lever. To lock the
glovebox door, insert the master key and turn it
clockwise.
With the tail lights on, the glovebox light will come on
when the glovebox door is open.
The trunk lid opener main switch is installed inside the
glovebox. See page 100 for further information.
For the CD automatic changer, see page 232.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the glovebox door closed
while driving.

INTERIOR EQUIPMENT
82
GARAGE DOOR OPENER
The garage door opener is manufactured under
license from HomeLink and can be programmed
to operate garage doors, estate gates, security
lighting, etc.
(a) Programming HomeLink
14E046a

INTERIOR EQUIPMENT
83
The
HomeLink
 has 3 buttons and can be
programmed to operate 3 separate devices.
Prepare the HomeLink
 for programming by
erasing all codes or the memorized data
programmed by the former owner. Follow the
procedure in º(c) Erasing the garage door opener
memoryº.
1. Decide which one of the 3 buttons you want to
program. Push and hold down the button for about 20
seconds until the indicator light begins to flash. While
holding this button, follow steps º2º and º3º. 2. Bring the hand held garage door opener within about
25 mm (1 in.) of the button being programmed and push
the button on the hand held garage door opener. The
signal from the hand held garage door opener is sent to
the vehicle's opener.
3. When the frequency and code is registered, the
indicator light flashes rapidly. At this point, you can
release both buttons.
4. To program the remaining buttons, repeat steps º1º
through º3º.
If you want to replace an existing program with a new
program, select the button you want to
program. Follow
the procedure from step 1.
If the transmitter has a ºrolling code featureº, it is
necessary to program the in±garage receiver after
programming HomeLink
.
1. Locate the ºtrainingº or ºlearningº button on the
in±garage receiver and push and release this
button. Location of the button may vary by the
garage door opener manufacturer.
2. Firmly push and release the trained HomeLink

button 2 times (some garage door manufacturer
may require you to push the HomeLink button up
to 3 times) to complete the process.
The garage door should now operate when the
HomeLink
 button is pushed.

INTERIOR EQUIPMENT
84Do not use the HomeLink
 universal transmitter with
any garage door opener that lacks the safety stop and
reverse feature as required by Federal Safety
Standards. This includes any garage door opener
model manufactured before April 1, 1982.
CAUTION
When programming or operating the garage door
opener, make sure there is no one around the moving
door. It is dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds
as long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized
data will be erased. FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Rules part 15.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference that may be received,
including interference that may cause undesired
operation. WARNING: This transmitter has
been tested and complies with FCC and
DOC/MDC rules. Changes or modifications
not expressly approved by the partly
responsible for compliance could void the
user's authority to operate the device.