1999 DODGE RAM fuse

15) Remove transmission control relay. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance of transmission control relay output
circuit between ground and transmission control relay harness
connector. If resistance is less than 5 ohms, repair short to ground
in transmission control relay output circuit. If resistance is 5 ohms
or greater, go to next step.
16) Measure resistance of transmission control relay output
circuit between transmission control relay connector and TCC solenoid
harness connector. If resistance is greater than 5 ohms, repair open
transmission control relay output circuit. If resistance is 5 ohms or
less, go to next step.
17) Turn ignition on. Measure voltage between ground and B+
circuit at transmission control relay harness connector. If voltage is
10 volts or less, repair open fused B+ circuit. If resistance is
greater than 10 volts, replace transmission control relay.
18) Record freeze frame data to determine conditions when
code was set. Using freeze frame data and wiring diagram as a guide,
inspect wiring and connectors. Repair wiring harness as necessary. If
wiring and connectors are okay, go to next step.
19) Using scan tool, clear DTCs. Start engine and check for
DTCs. Wiggle wiring harness between TCC solenoid and PCM. If DTC P0743
resets, repair wiring harness as necessary. If DTC P0743 does not
reset, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM.
Testing is complete.
DTC P0748: GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIRCUITS
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on governor pressure solenoid control circuit at
the Powertrain Control Module (PCM) does not match desired voltage for\
4.8 seconds.
Possible Causes
* Fused B+ circuit open.
* Solenoid and harness assembly defective.
* Governor pressure solenoid out of tolerance.
* Transmission control relay defective.
* Governor pressure solenoid control circuit shorted to
ground.
* Governor pressure solenoid harness defective.
* Governor pressure solenoid control circuit open.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure (AN & DN Bodies)
1) Using scan tool, read DTCs. If DTC P1765 is set, go to DTC
DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is
not set, go to next step.
2) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 1st gear and read governor pressure voltage. If voltage
is one volt or greater, go to step 5). If voltage is less than one
volt, go to next step.
3) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between governor
pressure solenoid and PCM. If DTC P0748 resets, repair wiring harness
as necessary. If DTC P0748 does not reset, go to next step.
4) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC

1st gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
15) Drain transmission fluid and remove oil pan. Disconnect
governor pressure solenoid harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance across governor pressure solenoid
terminals. If resistance is 2.5 ohms or less, go to next step. If
resistance is greater than 2.5 ohms, go to step 17).
16) Replace governor pressure solenoid. Replace oil pan and
fill with fluid. Reconnect all disconnected harness connectors. Using
scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st
gear and read governor pressure voltage. If voltage is one volt or
greater, replace PCM. If voltage is less than one volt, test is
complete.
17) Repair or replace transmission solenoid and harness
assembly. Reconnect all disconnected harness connectors. Using scan
tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st gear and
read governor pressure voltage. If voltage is one volt or greater,
replace PCM. If voltage is less than one volt, test is complete.
18) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
19) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If
resistance is 5 ohms or less, go to next step.
20) Measure resistance between ground and transmission
control relay output circuit at transmission solenoid harness
connector. If resistance is less than 5 ohms, repair open in
transmission control relay output circuit. If resistance is 5 ohms or
greater, replace transmission control relay.
Diagnostic Procedure (AB, BR & WJ Bodies)
NOTE: On WJ body, if all solenoid codes, P0743, P0748 and P0753 are
set, go to test DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL
CIRCUIT before proceeding.
1) Using scan tool, read DTCs. On BR and WJ bodies, go to
next step. On AB body, if DTC SPECIFIC GOOD TRIPS counter is not
displayed or displayed count is not "0", go to step 20). If DTC
SPECIFIC GOOD TRIPS counter is displayed and displayed count is "0",
indicating DTC still exists, go to next step.
2) If DTC P1765 is also set, go to DTC DTC P1765: TRANS 12-
VOLT SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is not set, go to next
step.
3) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 1st gear and read governor pressure voltage. If voltage
is one volt or greater, go to step 20). If voltage is less than one
volt, go to next step.
4) Turn ignition off. Disconnect transmission solenoid
harness connector. Turn ignition on. Using scan tool, actuate
transmission control relay. Measure voltage between ground and
transmission relay output circuit at transmission solenoid harness
connector. If voltage does not switch from zero to greater than 10
volts, go to step 17). If voltage switches from zero to greater than
10 volts, go to next step.
5) Turn ignition off. Disconnect PCM harness connectors.

complete.
16) Repair or replace transmission solenoid and harness
assembly. Reconnect all disconnected harness connectors. Using scan
tool, perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 1st gear and
read governor pressure voltage. If voltage is one volt or greater,
replace PCM. If voltage is less than one volt, test is complete.
17) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
18) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If
resistance is 5 ohms or less, go to next step.
19) Measure resistance between ground and transmission
control relay output circuit at transmission solenoid harness
connector. If resistance is less than 5 ohms, repair short to ground
in transmission control relay output circuit. If resistance is 5 ohms
or greater, replace transmission control relay.
20) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between governor
pressure solenoid and PCM. Note if DTC P0748 resets. If DTC P0748
resets, repair wiring harness as necessary. If DTC P0748 does not
reset, go to next step.
21) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P0751: O/D SWITCH PRESSED (LO) MORE THAN 5 MIN
Circuit Description
Circuit is monitored after engine is running for 10 seconds
and reviewed every 440ms. Code sets if overdrive switch is held low
for 5 minutes or more from time of closure or ignition on.
Possible Causes
* Fused B+ circuit open.
* Solenoid and harness assembly defective.
* Governor pressure solenoid out of tolerance.
* Transmission control relay defective.
* Governor pressure solenoid control circuit shorted to
ground.
* Governor pressure solenoid harness defective.
* Governor pressure solenoid control circuit open.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure
1) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between ground
and Overdrive (O/D) off switch sense circuit at Gray PCM harness
connector C3. If resistance is less than 5 ohms, go to next step. If
resistance is 5 ohms or greater, go to step 3).
2) Disconnect O/D switch harness connector. Inspect connector
and terminals for damage. Repair as necessary. If connector and
terminals are okay, measure resistance between ground and O/D off

times so that vehicle attempts to shift from 4thgear to 3rd gear and
back. If vehicle does not shift between 3rd and 4th gear, replace PCM.
If vehicle shifts between 3rd and 4th gear, testing is complete.
8) Turn ignition off. Measure resistance between ground and
3-4 shift solenoid control circuit at White PCM harness connector C2.
If resistance is less than 5 ohms, repair short to ground in 3-4 shift
solenoid control circuit. If resistance is 5 ohms or greater, go to
next step.
9) Reconnect transmission solenoid harness connector. Measure
resistance between ground and 3-4 shift solenoid control circuit at
White PCM harness connector C2. If resistance is less than 5 ohms,
replace transmission solenoid harness assembly. If resistance is 5
ohms or greater, go to next step.
10) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, measure resistance between
transmission control relay output circuit at transmission control
relay connector and 3-4 shift solenoid control circuit at White PCM
harness connector C2. If resistance is 26-40 ohms, replace PCM. If
resistance is not 26-40 ohms, go to next step.
11) Measure resistance between transmission control relay
output circuit at transmission control relay connector and 3-4 shift
solenoid control circuit at White PCM harness connector C2. If
resistance is greater than 40 ohms, go to next step. If resistance is
less than 26 ohms, go to step 13).
12) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance of 3-4 shift
solenoid circuit between White PCM harness connector C2 and
transmission solenoid harness connector. If resistance is 5 ohms or
greater, repair open 3-4 shift solenoid circuit. If resistance is less
than 5 ohms, replace transmission solenoid and harness assembly.
13) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance of 3-4 shift
solenoid circuit and all other circuits at transmission solenoid
harness connector. If resistance is less than 5 ohms between any 2
circuits, go to next step. If resistance is not less than 5 ohms
between any 2 circuits, go to step 15).
14) Repair 3-4 shift solenoid control circuits that were
shorted together. Reconnect all disconnected harness connectors. Road
test vehicle and reach a speed of 50 MPH. Depress Overdrive (OD)
switch 4 times so that vehicle attempts to shift from 4thgear to 3rd
gear and back. If vehicle does not shift between 3rd and 4th gear,
replace PCM. If vehicle shifts between 3rd and 4th gear, testing is
complete.
15) Replace transmission harness inside transmission and
solenoid pack assembly. Reconnect all disconnected harness connectors.
Road test vehicle and reach a speed of 50 MPH. Depress Overdrive (OD)
switch 4 times so that vehicle attempts to shift from 4th gear to 3rd
gear and back. If vehicle does not shift between 3rd and 4th gear,
replace PCM. If vehicle shifts between 3rd and 4th gear, testing is
complete.
16) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
17) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If

connector. If resistance is 5 ohms or greater, repair open 3-4 shift
solenoid circuit. If resistance is less than 5 ohms, replace
transmission solenoid and harness assembly.
12) Measure resistance between transmission control relay
output circuit at transmission control relay connector and 3-4 shift
solenoid control circuit at White PCM harness connector C2. If
resistance is 26-40 ohms, replace PCM. If resistance is not 26-40
ohms, test is complete.
13) Remove transmission control relay. Inspect transmission
control relay connector and terminals for damage. Repair as necessary.
If connector and terminals are okay, turn ignition on. Measure voltage
between ground and fused B+ circuit at transmission control relay
connector. If voltage is 10 volts or less, repair open fused B+
circuit. If voltage is greater than 10 volts, go to next step.
14) Turn ignition off. Measure resistance of transmission
control relay output circuit at transmission control relay connector
and TCC solenoid harness connector. If resistance is greater than 5
ohms, repair open transmission control relay output circuit. If
resistance is 5 ohms or less, go to next step.
15) Measure resistance between ground and transmission
control relay output circuit at transmission solenoid harness
connector. If resistance is less than 5 ohms, repair short to ground
in transmission control relay output circuit. If resistance is 5 ohms
or greater, replace transmission control relay.
16) Using scan tool, erase DTCs. Start engine. Attempt to
duplicate data and reset code. Using wiring diagram as a guide,
inspect wiring and connectors. Repair wiring harness as necessary. If
wiring and connectors are okay, go to next step.
17) Wiggle wiring harness between TCC solenoid and PCM. Note
if DTC P0753 resets. If DTC P0753 resets, repair wiring harness as
necessary. If DTC P0753 does not reset, replace PCM and see INACTIVE
DTC CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
Diagnostic Procedure (WJ Body)
NOTE: If all solenoid codes, P0743, P0748 and P0753 are set, go to
test DTC P1765: TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT
before proceeding.
1) Using scan tool, read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to next
step. If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to step 16).
2) Road test vehicle and reach a speed of 50 MPH. Depress
Overdrive (OD) switch 4 times so that vehicle attempts to shift from
4th gear to 3rd gear and back. If vehicle does not shift between 3rd
and 4th gear, go to step 4). If vehicle shifts between 3rd and 4th
gear, go to next step.
3) Record freeze frame data to determine conditions when code
was set. Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
4) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair
as necessary. If connector and terminals are okay, turn ignition on.
Using scan tool, actuate transmission control relay. Measure voltage
between ground and transmission relay output circuit at transmission
solenoid harness connector. If voltage does not switch from zero to
greater than 10 volts, go to step 12). If voltage switches from zero
to greater than 10 volts, go to next step.
5) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If

connectors and terminals are okay, measure resistance between ground
and 3-4 shift solenoid control circuit at PCM harness connector. If
resistance is 5 ohms or greater, go to next step. If resistance is
less than 5 ohms, repair short to ground in 3-4 shift solenoid
circuit.
6) Measure resistance of 3-4 shift solenoid circuit between
White PCM harness connector C2 and transmission solenoid harness
connector. If resistance is 5 ohms or greater, repair open 3-4 shift
solenoid circuit. If resistance is less than 5 ohms, go to next step.
7) Turn ignition on. Measure voltage between ground and 3-4
shift solenoid control circuit at PCM harness connector. If voltage is
greater than one volt, repair 3-4 shift solenoid control circuit for
short to voltage. If voltage is one volt or less, go to next step.
8) Turn ignition off. Remove transmission control relay.
Inspect transmission control relay connector and terminals for damage.
Repair as necessary. If connector and terminals are okay, measure
resistance between transmission control relay output circuit at
transmission control relay connector and 3-4 shift solenoid control
circuit at White PCM harness connector C2. If resistance is 26-40
ohms, go to next step. If resistance is not 26-40 ohms or less,
replace 3-4 shift solenoid.
9) Measure resistance between ground and transmission control
relay output circuit at transmission control relay connector. If
resistance is less than 5 ohms, repair short to ground in transmission
control relay output circuit. If resistance is 5 ohms or greater, go
to next step.
10) Measure resistance between transmission control relay
output circuit between transmission control relay connector and
transmission solenoid harness connector. If resistance is 5 ohms or
greater, repair open transmission control relay output circuit. If
resistance is less than 5 ohms, go to next step.
11) Turn ignition on. Measure voltage between ground and
fused B+ circuit at transmission control relay connector. If voltage
is 10 volts or less, repair open fused B+ circuit. If voltage is
greater than 10 volts, replace PCM.
12) Disconnect transmission control relay. Inspect connector
and terminals for damage. Repair as necessary. If connector and
terminals are okay, turn ignition on. Replace transmission control
relay. Using scan tool, actuate transmission control relay. Measure
voltage between ground and transmission relay output circuit at
transmission solenoid harness connector. If voltage is greater than 10
volts, replace transmission control relay. If voltage is 10 volts or
less, go to next step.
13) Measure resistance of transmission control relay output
circuit between transmission control relay connector solenoid harness
connector. If resistance is 5 ohms or greater, repair open in
transmission control relay output circuit. If resistance is less than
5 ohms, go to next step.
14) Measure resistance of transmission control relay output
circuit between ground and transmission control relay connector. If
resistance is 5 ohms or greater, go to next step. If resistance is
less than 5 ohms, repair short to ground in transmission control relay
output circuit.
15) Turn ignition on. Measure voltage between ground and
fused B+ circuit at transmission control relay connector. If voltage
is 10 volts or less, repair open fused B+ circuit. If voltage is
greater than 10 volts, test is complete.
16) Using scan tool, erase DTCs. Start engine. Attempt to
duplicate data and reset code. Using wiring diagram as a guide,
inspect wiring and connectors. Repair wiring harness as necessary. If
wiring and connectors are okay, wiggle wiring harness between TCC
solenoid and PCM. Note if DTC P0753 resets. If DTC P0753 resets,
repair wiring harness as necessary. If DTC P0753 does not reset,

scan tool, read governor pressure sensor voltage. If voltage is
greater than 4.65 volts, go to next step. If voltage is 4.65 volts or
less, go to step 11).
4) Turn ignition off. Disconnect transmission solenoid
harness connector. Disconnect PCM harness connectors. Inspect
connectors and terminals for damage. Repair as necessary. If connector
and terminals are okay, measure resistance of governor pressure sensor
signal circuit between transmission solenoid harness connector and
White PCM harness connector C2. If resistance is greater than 5 ohms,
repair open governor pressure sensor signal circuit. If resistance is
5 ohms or less, go to next step.
5) Measure resistance of sensor ground circuit between Black
PCM harness connector C1 and transmission solenoid harness connector.
If resistance is greater than 5 ohms, repair open ground circuit. If
resistance is 5 ohms or less, go to next step.
6) Connect a fused jumper wire between fused B+ circuit and
transmission control relay output circuit at transmission relay
connector. Turn ignition on. Measure voltage between ground and
governor pressure signal circuit at White PCM harness connector C2. If
voltage is greater than 10 volts, repair governor pressure signal
circuit for short to voltage. If voltage is 10 volts or less, go to
next step.
7) Turn ignition off. Drain transmission fluid and remove oil
pan. Reconnect transmission solenoid harness connector. Disconnect
governor pressure sensor harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, measure resistance of governor pressure sensor ground
circuit between Black PCM harness connector C1 and governor pressure
sensor harness connector. If resistance is greater than 5 ohms, repair
or replace transmission solenoid and harness assembly. If resistance
is 5 ohms or less, go to next step.
8) Reconnect all harness connectors except governor pressure
sensor harness connector. Carefully connect a fused jumper wire
between ground circuit and governor pressure signal circuit at
governor pressure sensor harness connector. Turn ignition on. Using
scan tool, read governor pressure sensor voltage. If voltage is .1
volt or less, replace governor pressure sensor. If resistance is
greater than .1 volt, go to next step.
9) Measure resistance of governor pressure sensor signal
circuit between White PCM harness connector C2 and governor pressure
sensor harness connector. If resistance is greater than 5 ohms, repair
or replace transmission solenoid and harness assembly. If resistance
is 5 ohms or less, go to next step.
10) Turn ignition on. Measure voltage between ground and
governor pressure signal circuit at governor pressure sensor harness
connector. If voltage is greater than one volt, repair or replace
transmission solenoid and harness assembly. If voltage is one volt or
less, replace PCM.
11) If governor pressure voltage is less than .12 volt, go to
DTC P1764: GOVERNOR PRESSURE SENSOR VOLTS TOO LOW. If governor
pressure voltage is .12 volt or greater, go to next step.
12) If governor pressure voltage is .12-.80 volt, go to next
step. If governor pressure voltage is .80 volt or greater, go to step
15).
13) Wiggle wiring harness between PCM and governor pressure
sensor while monitoring governor pressure voltage on scan tool. If
voltage changes while wiggling wiring harness, repair wiring harness
as necessary. If voltage does not change, go next step.
14) Conditions required to set DTC P1763 are not present at
this time. DTC P1763 sets if governor pressure sensor input is greater
than 4.89 volts for 8.36 seconds. Possible causes are: PCM internally
shorted or open, incorrectly wired, dirty or corroded connectors or
open or shorted wiring. See INACTIVE DTC CONDITION under SELF-

9) Check and record freeze frame data to determine conditions
which set code. Turn ignition off. Disconnect transmission solenoid
harness connector. Disconnect PCM harness connectors. Inspect
connectors and terminals for damage. Repair as necessary. If connector
and terminals are okay, measure resistance of governor pressure sensor
ground circuit between transmission solenoid harness connector and
Black PCM harness connector C1. If resistance is greater than 5 ohms,
repair open governor pressure sensor ground circuit. If resistance is
5 ohms or less, go to next step.
10) Measure resistance of governor pressure sensor signal
circuit between White PCM harness connector C2 and governor pressure
sensor harness connector. If resistance is greater than 5 ohms, repair
open governor pressure sensor signal circuit. If resistance is 5 ohms
or less, go to next step.
11) Connect a fused jumper wire between fused B+ circuit and
transmission control relay output circuit at transmission relay
connector. Turn ignition on. Measure voltage between ground and
governor pressure signal circuit at White PCM harness connector C2. If
voltage is greater than one volt, repair governor pressure signal
circuit for short to voltage. If voltage is one volt or less, go to
next step.
12) Drain transmission fluid and remove oil pan. Disconnect
pressure/temperature sensor harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, reconnect transmission solenoid harness connector. Carefully
connect a fused jumper wire between ground circuit and governor
pressure signal circuit at governor pressure sensor harness connector.
Turn ignition on. Using scan tool, read governor pressure sensor
voltage. If voltage is .1 volt or less, replace pressure/temperature
sensor. If voltage is greater than .1 volt, go to next step.
13) Measure resistance of governor pressure sensor signal
circuit between White PCM harness connector C2 and governor pressure
sensor harness connector. If resistance is greater than 5 ohms, repair
or replace transmission solenoid and harness assembly. If resistance
is 5 ohms or less, go to next step.
14) Measure resistance of governor pressure sensor ground
circuit between Black PCM harness connector C1 and governor pressure
sensor harness connector. If resistance is greater than 5 ohms, repair
or replace transmission solenoid and harness assembly. If resistance
is 5 ohms or less, go to next step.
15) Turn ignition on. Measure voltage between ground and
governor pressure signal circuit at governor pressure sensor harness
connector. If voltage is greater than one volt, repair or replace
transmission solenoid and harness assembly. If voltage is one volt or
less, replace PCM.
16) Turn ignition off. Disconnect PCM harness connectors.
Disconnect transmission solenoid harness connector. Inspect connector
and terminals for damage. Repair as necessary. If connector and
terminals are okay, measure resistance of sensor ground circuit
between Black PCM harness connector C1 and solenoid harness connector.
If resistance is less than 5 ohms, go to next step. If resistance is 5
ohms or greater, repair open in governor pressure sensor ground
circuit.
17) Turn ignition on. Measure voltage between ground and
governor pressure signal circuit at governor pressure sensor harness
connector. If voltage is greater than one volt, repair governor
pressure signal circuit for short to voltage. If voltage is one volt
or less, go to next step.
18) Turn ignition off. Measure resistance of governor
pressure sensor signal circuit between White PCM harness connector C2
and solenoid harness connector. If resistance is greater than 5 ohms,
repair open governor pressure sensor signal circuit. If resistance is
5 ohms or less, go to next step.