1999 DODGE RAM ECO mode

Use only NEW, moisture-free refrigerant oil in A/C systems.
Refrigerant oil is highly refined with a very low moisture content.
Oil container must be tightly closed when not in use, or moisture from
air will be absorbed into refrigerant oil.
Refrigerant R-134a systems use Polyalkylene Glycol (PAG)
refrigerant oil. Using a mineral oil based lubricant with R-134a
systems will result in A/C compressor failure due to lack of proper
lubrication.
All compressors have different lubrication requirements and
use different Polyalkylene Glycol (PAG) refrigerant oils. Use only the\
specified PAG refrigerant oil for the appropriate system and A/C
compressor. Always check the underhood A/C specification label or A/C
compressor label before adding refrigerant oil to A/C
compressor/system. See listing of refrigerant oils currently available
from the vehicle manufacturers.
NOTE: PAG oil absorbs moisture very rapidly, 2.3-5.6 percent by
weight as compared to a mineral oil absorption rate of .005
percent by weight.
CHRYSLER CORP., JEEP & EAGLE
Use ND-8 PAG oil, SUN PAG 56 oil, SP-10 PAG oil, or SP-20 PAG
oil.
FORD MOTOR CO.
Use YN-12B or YN-12C PAG Refrigerant Oil (specification WSH-
M1C231-B) or SP-20 PAG Oil (specification WST-M1C231-B2).
GENERAL MOTORS
On all models except Saturn, use PAG Refrigerant Oil (Part
No. 12345923). On Saturn, use Saturn PAG refrigerant oil.
SERVICING PRECAUTIONS
DISCHARGING SYSTEM
Discharge A/C system, using approved refrigerant
recovery/recycling equipment before loosening any fittings. Follow
refrigerant recovery/recycling equipment manufacturer's instructions.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when loosening or
tightening fittings. Some refrigerant lines are connected with a
spring-lock coupling. Special tools may be required to disconnect
lines. To prevent dirt and moisture from entering system, cap all
openings as soon as lines are removed. DO NOT remove service valve
caps until ready to connect lines and fittings.
NOTE: All R-134a based systems use 1/2-16 ACME threaded fittings.
Ensure all replacement parts match the connections of the
system being worked on.
CONNECTING LINES & FITTINGS
Always use new a gasket or "O" rings when connecting lines or

Contour, Cougar, Escort, Mustang, Mystique, Tracer and Windstar,
drill two 1/2" holes in bottom of old accumulator, and drain. On
all models, add the same amount of oil drained plus 2 ounces of
refrigerant oil to new accumulator.
(2) - Add refrigerant oil following replacement of other system
components such as hoses, fixed orifice tube, A/C clutch cycling
switch, A/C compressor pressure relief valve, system pressure
cut-off switch, or service valve, compressor shaft seal, "O"
ring or hose leaks.
( 3) - If all lines have been replaced.









\









\









\









\









\









\









\







HARRISON HD6/HT6, HD6/HR-6HE 6-CYL., V5 5-CYL. & V7 7-CYL.
NOTE: Replacement compressor may be shipped with 8-9 ounces of
refrigerant oil. Drain shipping refrigerant oil into a clean
container and retain for use.
1) If possible, operate system for several minutes to
stabilize system. Turn engine off. Discharge A/C system, using
approved refrigerant recovery/recycling equipment. Remove A/C
compressor. Drain and measure refrigerant oil from old compressor
through suction and discharge ports, and drain plug.
2) If no compressor oil leaks exist, and more than one ounce
is drained, add amount drained from old compressor. If less than one
ounce is drained from old compressor, add 2 ounces of refrigerant oil.
3) When replacing other A/C components, add specified amount
of refrigerant oil to component. See HD6/HT6, HD6/HR-6HE, V5 & V7
COMPONENT REFRIGERANT OIL CAPACITIES table. Install compressor drain
plug and compressor. Evacuate and charge system. Perform leak test.
Ensure A/C system is operating properly.
NOTE: Approximately 3 ounces of refrigerant oil, suspended in
refrigerant, will be lost due to a large, abrupt leak. When
replacing a faulty A/C component, add amount of oil specified
for component plus 3 ounces to compensate for oil loss. If
oil cannot easily be added to component, add it to
accumulator.
HD6/HT6, HD6/HR-6HE V5 & V7 COMPONENT REFRIGERANT OIL CAPACITIES









\









\









\









\









\









\









\







Component Ounces
Cars
Accumulator/Receiver-Drier
Except "F", "N", "V" & "W" Bodies .......................... 3.5
"F", "N", "V" & "W" Bodies ................................. ( 1)
Compressor
"C" Body ................................................... ( 2)
"E", "K", "V" & "Y" Bodies ................................. 2.0
"F", "G", "H", "J", "P", "N" & "W" Bodies .................. ( 3)
Condenser .................................................... 1.0
Evaporator ................................................... 3.0
Trucks & Vans
Accumulator/Receiver-Drier
Except "U" Series .......................................... 3.5
"U" Series ................................................. ( 4)
Compressor
Except "U" Series .......................................... ( 3)
"U" Series ................................................. ( 2)
Condenser
Except "U" Series .......................................... 1.0
"U" Series ................................................. ( 4)

Evaporator
Except "U" Series .......................................... 3.0
"U" Series ................................................. (4)
( 1) - Add amount drained from old accumulator/receiver-drier plus one
ounce.
( 2) - Ensure replacement compressor contains the same amount of
refrigerant oil as was drained from old compressor.
( 3) - Drain and measure refrigerant oil from old compressor. If old
compressor had less than one ounce, add 2 ounces of refrigerant
oil to replacement compressor. If old compressor had more than
one ounce, add the same amount of refrigerant oil to replacement
compressor.
( 4) - Information not available from manufacturer.









\









\









\









\









\









\









\







NIPPONDENSO 10-CYLINDER
General Motors (Metro & Tracker)
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain, measure
and discard refrigerant oil from old compressor. Drain refrigerant oil
from replacement compressor. Add refrigerant oil to replacement
compressor equal to amount drained from oil compressor.
2) Add specified amount of refrigerant oil to components that
are replaced during compressor replacement. See NIPPONDENSO 10-
CYLINDER COMPONENT REFRIGERANT OIL CAPACITIES table. Install A/C
compressor. Evacuate and charge system. Perform leak test.
NIPPONDENSO 10-CYLINDER COMPONENT REFRIGERANT OIL CAPACITIES









\









\









\









\









\









\









\







Component Ounces
Compressor ..................................................... 3.0
Condenser .................................................. 0.7-1.0
Receiver-Drier ................................................. 0.3
System Total ................................................... 3.4









\









\









\









\









\









\









\







NIPPONDENSO 10PA17/10PA17C 10-CYL.
Chrysler Corp. (Avenger & Sebring Coupe)
1) Remove A/C compressor. Drain and measure oil from old
compressor. Replacement compressor is shipped with 3.4 ounces of oil.
From replacement compressor, drain the difference between system oil
capacity and amount of oil drained from replacement compressor.
2) Add specified amount of refrigerant oil to components that
are replaced during compressor replacement. See 10PA17/10PA17C
COMPONENT REFRIGERANT OIL CAPACITIES table. When replacing components
listed, DO NOT exceed system total capacity.
Chrysler Corp. & Jeep (Caravan, Concorde, Grand Cherokee,
Intrepid, LHS, Neon, Town & Country, Voyager & 300M)
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Disconnect refrigerant hoses at
compressor. Remove compressor bolts and A/C compressor.
2) Remove suction port on top of A/C compressor, and drain
and measure oil. On Grand Cherokee, add the same amount of oil drained
from old compressor to replacement compressor.
3) On all other models, add amount of oil to compressor equal
to the total system capacity minus amount retained in components that
are not being replaced. See 10PA17/10PA17C COMPONENT REFRIGERANT OIL
CAPACITIES table. Install A/C compressor. Evacuate and charge A/C

CLUTCH ASSEMBLY
Removal (Except Grand Cherokee)
Remove compressor shaft bolt. Remove clutch plate and shims.
Tighten a 10-mm bolt into clutch hub bolt hole to remove clutch hub
and shims. Remove snap ring, and remove rotor and pulley assembly.
Remove snap ring, and disconnect clutch coil lead. Remove clutch coil.
Installation
1) Install clutch coil so pin in back of coil aligns with
hole in front compressor housing. Connect clutch coil lead. Install
snap ring with bevel side facing outward. Ensure snap ring is properly
seated in groove. Install rotor and pulley assembly. Install shims and
snap ring. Install clutch hub.
2) Install dial indicator at front of clutch hub to measure
clutch hub air gap. Using battery voltage, energize clutch coil.
Proper air gap is 0.014-0.026" (0.35-0.65 mm). Add or remove shims to
obtain correct air gap. Install compressor shaft bolt. On Concord and
Intrepid, tighten compressor shaft bolt to 11-15 ft. lbs. (15-20 N.m).\
On all other models, tighten compressor shaft bolt to 10 ft. lbs. (14
N.m).
NOTE: On Grand Cherokee, compressor clutch can be serviced in
vehicle without discharging A/C system.
Removal (Grand Cherokee)
Disconnect and isolate negative battery cable. Remove
serpentine drive belt. Remove compressor shaft bolt. Using a plastic
mallet, tap clutch plate to loosen from compressor shaft. Remove
clutch plate, shaft key and shims. See Fig. 5. Remove snap ring, and
remove pulley assembly. Remove snap ring, and disconnect clutch coil
lead. Remove clutch coil.
Installation
1) Install clutch coil so pin in back of coil aligns with
hole in front compressor housing. Connect clutch coil lead. Install
snap ring with bevel side facing outward. Ensure snap ring is properly
seated in groove. Align snap ring eyelets to the left or right of
clutch coil pin. Install rotor and pulley assembly. Install shims and
snap ring. Install clutch hub.
2) Hold clutch plate tight against shims and measure air gap
between clutch plate and pulley face. Air gap should be 0.014-0.026"
(0.35-0.65 mm). Add or remove shims as necessary. Install compressor
shaft bolt. Tighten compressor shaft bolt to 115 INCH lbs. (13 N.m).
To complete installation, reverse removal procedure.
3) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
SHAFT SEAL
NOTE: Shaft seal replacement procedure is for 10PA17C compressor.
Shaft seal replacement procedure for 10PA17 compressor is not
available.
Removal
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain oil from
compressor, and measure amount drained. Remove clutch hub, shims,
rotor and pulley assembly, and clutch coil. See CLUTCH ASSEMBLY. See

Installation (Cherokee & Wrangler)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub. Using Installer (C-
6871), press pulley and bearing assembly onto compressor housing hub.
Thread installer on compressor shaft and tighten nut until pulley
assembly is seated.
2) Install external front snap ring with beveled side facing
outward. Ensure snap ring is properly seated. Install compressor shaft
key and original shims. Using a plastic mallet and Driver (C-6463),
install clutch plate on compressor shaft. Tighten compressor shaft nut
to 10 ft. lbs. (14 N.m).
3) Using feeler gauge, measure air gap between clutch plate
and pulley assembly in several areas. Air gap should be 0.016-0.031"
(0.41-0.79 mm). If air gap is not within specification, adjust shim
thickness as necessary. If air gap is not consistent around clutch
plate, lightly pry up or tap down on clutch plate to make corrections.
To complete installation, reverse removal procedure.
Installation (Dakota, Durango & Ram Pickup)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub.
2) Install Handle (6464) and Driver (6143) into pulley
assembly bearing cavity. Ensure outer edge of driver rests firmly on
inner race of bearing. Using hammer, install pulley and bearing
assembly. While tapping on handle, guide pulley and bearing assembly
to prevent binding. Ensure pulley assembly bottoms against compressor
housing. Install external snap ring.
3) Install original shim(s) and compressor shaft key. Use a
hammer and Shaft Protector (6141-2) to install clutch plate on
compressor shaft. Ensure clutch plate bottoms out on clutch shims.
Replace compressor shaft nut and tighten compressor shaft nut to 10
ft. lbs. (14 N.m).
4) Measure air gap between clutch plate and pulley assembly
in several areas. Air gap should be 0.016-0.031" (0.41-0.79 mm). If
air gap is not within specification, adjust shim thickness as
necessary. If air gap is not consistent around clutch plate, lightly
pry up or tap down on clutch plate to make corrections. To complete
installation, reverse removal procedure. Ensure A/C system operates
properly.
5) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
Removal (Ford "F" Series Super Duty Pickup)
1) Disconnect and isolate negative battery cable. Discharge
A/C system, using approved refrigerant recovery/recycling equipment.
Disconnect clutch coil harness connector and remove compressor. Drain
oil from compressor, and measure amount drained.
2) Using Spanner Wrench (T70P-4067-A), hold clutch plate and\
remove compressor shaft nut. See Fig. 1. If necessary, use a steering
wheel puller to remove clutch plate and shim(s).
3) Using a flat-blade screwdriver, remove pulley assembly
bearing dust cover. Remove compressor shaft key and internal bearing
snap ring. Remove external front housing snap ring.
4) Install jaws of rotor puller into pulley assembly internal
bearing snap ring groove. Install shaft protector over compressor
shaft. Install puller flange plate on jaws. Install 2 puller bolts
through puller flange plate into jaws and hand tighten. Tighten pulley
center bolt clockwise and remove pulley assembly from compressor.

5) Once compressor shaft nut is tightened, check air gap
between clutch plate and pulley surface in at least 4 places. Readjust
air gap if necessary. Install A/C compressor. Evacuate and charge
system. Perform leak test. Ensure A/C system is operating properly.
6) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
SHAFT SEAL
Shaft seal is not serviceable. If excessive oil is present on
pulley and plate friction surfaces or on compressor shaft nose area,
replace compressor.
ZEXEL ROTARY VANE
CLUTCH ASSEMBLY
NOTE: Discharging A/C system and removing refrigerant lines from
compressor is not necessary to service clutch assembly.
Removal
1) Loosen tensioner and remove drive belt from pulley.
Disconnect clutch electrical connector. Remove compressor mounting
bolts. With refrigerant lines connected lift compressor upward and
forward. Install one front mounting bolt through bottom rear
compressor mounting ear. Tighten bolt so compressor is supported by
mounting bracket.
2) Using Clutch Drive Plate Holder (SA9510AC), remove clutch\
drive plate center bolt. Insert Clutch Drive Plate Remover Sleeve
(SA9506AC) into center of drive plate. Install remover bolt. While
holding clutch remover sleeve, tighten remover bolt and remove drive
plate and shims.
3) Remove pulley external snap ring. Position Puller Center
Adapter (SA9149AC-2) over end of compressor shaft. Attach 3-jaw puller\
to back of pulley. Tighten puller bolt against pulley center adapter
and remove pulley. Remove clutch coil screws. Disconnect clutch coil
wire. Remove clutch coil.
Installation
1) Install coil in original position. Ensure electrical
connector is aligned with indent in front of compressor head. Tighten
screws to 44 INCH lbs. (5 N.m). Place Drive Plate Installer (SA9149AC\
-
3) and thrust bearing on installation bolt and insert through center
of pulley. Finger-tighten pulley installation bolt into compressor
shaft.
2) Finger-tighten nut on installation bolt to align pulley to
compressor. Hold end of bolt and tighten nut until pulley bottoms on
compressor. Loosen nut and remove installation bolt, thrust bearing
and drive plate installer. Install snap ring with tapered side out.
3) Install thrust bearing on installation bolt and insert
through clutch drive plate. Place original shims on installation bolt.
Thread bolt into compressor shaft. Hold end of bolt and tighten nut
until clutch drive plate bottoms out. Loosen nut and remove
installation bolt and thrust bearing. Install center bolt and tighten
to 115 INCH lbs. (13 N.m) using clutch drive plate holder.
4) Using a feeler gauge, measure air gap between drive plate
and pulley. Air gap should be 0.018-0.030" (0.46-0.76 mm). If air gap
is not as specified, add or remove shims as necessary. Install
compressor onto mounting bracket. Tighten front bolts to 36 ft. lbs.

BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument

assembly towards right side of vehicle and remove rear A/C-heater
assembly.
5) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS .
Removal (Ram Pickup - Front)
1) Disconnect negative battery cable. Drain cooling system.
In engine compartment, remove coolant hoses from heater core tubes.
Remove coolant overflow bottle.
2) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Disconnect refrigerant lines from
evaporator and plug or cover all openings in A/C system. Remove
instrument panel. See INSTRUMENT PANEL. Remove Powertrain Control
Module (PCM) and position aside. DO NOT disconnect 60-pin connector
from PCM.
3) Remove attaching nuts from studs on engine compartment
side of dash panel. Remove defrost duct. Disconnect electrical
connectors. Remove attaching nuts from studs in passenger compartment
side of dash panel. Remove A/C-heater assembly from vehicle. See
Fig. 5 .
4) Place A/C-heater assembly upside-down on work bench.
Remove screw securing floor duct to bottom of A/C-heater assembly and
slide floor duct off of center heat duct adapter. Unsnap center heat
duct adapter from bottom of A/C-heater assembly housing. Remove screw
hidden behind adapter. Remove remaining screws and separate A/C-heater
assembly.
Installation
Ensure mode door pivot pins are properly inserted in holes.
To complete installation, reverse removal procedure.
A/C-HEATER CONTROL PANEL R & I
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. On models equipped with
A/T, unlock ignition switch. Set parking brake and place gear selector
lever in "L" position. If equipped, set tilt steering column in lowest
position.
2) On all models, carefully pry bezel away from instrument
panel to disengage clips. Unplug connectors from cigarette lighter and
auxiliary power outlet. Disconnect fog light switch (if equipped).
Remove A/C-heater control panel screws.
3) Pull control panel outward enough to disconnect wiring
connector, vacuum harness, and temperature control cable. Remove A/C-
heater control panel. To install, reverse removal procedure. Adjust
temperature control cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT .
Removal & Installation (Ram Pickup)
1) Disconnect negative battery cable. Reach under driver's
side of instrument panel, near transmission tunnel and unplug A/C-
heater control panel to A/C-heater assembly vacuum harness connector.
Disconnect vacuum harness from center air duct.
2) On models equipped with A/T, unlock ignition switch. Set
parking brake and place gear selector lever in "L" position. If
equipped, set tilt steering column in lowest position.
3) On all models, remove screw securing cluster bezel to
instrument panel. See Fig. 6. Carefully pry bezel away from instrument
panel to disengage clips. Unplug connectors from cigarette lighter and
auxiliary power outlet.
4) Remove 4 screws attaching A/C-heater control panel. Pull
control panel outward enough to disconnect wiring connector, vacuum
harness and temperature control cable. Remove A/C-heater control