1999 DODGE RAM brake rotor

alternator belt lock emergency towing radio controls start stop button ignition

Page 55 of 1691

DODGE RAM 1999 Service Repair Manual or the vehicle manufacturers recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no lon

or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition. When a procedure states that required or suggested
repair or replacement is recommended, the customer must be informed of
the generally acceptable repair/replacement options whether or not
performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial

Page 319 of 1691

DODGE RAM 1999 Service Repair Manual
* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards

Page 321 of 1691

DODGE RAM 1999 Service Repair Manual satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve st

satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.

Page 342 of 1691

DODGE RAM 1999 Service Repair Manual reconditioning ......... B ........ (3) Require replacement.
Surface is rust-pitted .. B ....... Require reconditioning or
replacement of rotor according

reconditioning ......... B ........ (3) Require replacement.
Surface is rust-pitted .. B ....... Require reconditioning or
replacement of rotor according
to OEM specifications.
Surface is scored ....... B ... ( 4) Require reconditioning or
replacement of rotor according
to OEM specifications.
Thickness variation
(parallelism) exceeds OEM
specifications .......... B ....... Require reconditioning or
replacement of rotor according
to OEM specifications.
( 1) - Examples of severe corrosion are: composite plate
separated from friction surfaces and cooling fins
cracked or missing.
( 2) - Only applies to vehicles for which OEM "machine to"
specifications exist. If OEM does not supply "machine
to" specifications, the rotor may be worn to discard
specifications.
( 3) - If OEM does not supply "machine to" specifications,
you may machine to discard specifications.
( 4) - Scoring is defined as grooves or ridges in the friction
contact surface. Some vehicle manufacturers require
machining when scoring exceeds their allowable
specifications.
\
\
\
\
\
\
\

SELF-ADJUSTING SYSTEMS
SELF-ADJUSTING SYSTEM INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent .................... A ... Require repair or replacement
of bent part.
Broken .................. A ... Require repair or replacement
of broken part.
Inoperative ............. A ........... ( 1) Require repair or
replacement of inoperative
parts.
Missing ................. C .......... Require replacement of
missing part.
Star wheel does not turn
freely ................. A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\

SHOE HARDWARE
See BRAKE SHOE HARDWARE .
SHOES
See FRICTION MATERIAL .
SOCKETS
See BULB SOCKETS.
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)

Page 352 of 1691

DODGE RAM 1999 Service Repair Manual BRAK E S YSTE M
1999 D odge P ic ku p R 1500
1998-99 BRAKES
CHRY - Disc & Drum - Trucks & Vans - Except FWD
Dakota, Ram Pickup, Ram Van
DESCRIPTION & OPERATIO

BRAK E S YSTE M
1999 D odge P ic ku p R 1500
1998-99 BRAKES
CHRY - Disc & Drum - Trucks & Vans - Except FWD
Dakota, Ram Pickup, Ram Van
DESCRIPTION & OPERATION
All models are equipped with single-piston, sliding-caliper
front disc brakes with ventilated rotors. All models utilize self-
adjusting rear drum brakes. Rear Wheel Anti-Lock (RWAL) brake system
is standard on all models. Optional 4-wheel Anti-Lock (4WAL) brake
system is available on all models.
System also includes power brake booster, dual-reservoir
master cylinder and combination valve. Combination valve consists of
metering valve and pressure differential switch.
Models with diesel engine include a gear-driven vacuum pump.
Depending on speed of engine, pump produces 8-25 in. Hg. Models
without full-floating rear axle use 9", 10" or 11" single-anchor rear
brakes. Models with full-floating rear axle use 12" or 13" single-
anchor rear brakes.
NOTE: For information on Anti-Lock Brake Systems (ABS), see
appropriate ANTI-LOCK article.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
Complete Brake System
Before bleeding system, exhaust all vacuum from power unit by
depressing brake pedal several times. Bleed master cylinder using
bleeder screws (if equipped). Bleed wheel cylinders and calipers in
sequence. See BLEEDING SEQUENCE table.
BLEEDING SEQUENCE
\
\
\
\
\
\
\

Application Sequence
1999 Dakota & Ram Van .......... Master Cylinder, Combination Valve,
RR, LR, RF & LF
All Other Models ............... Master Cylinder, Combination Valve,
Rear Anti-Lock Valve, RR, LR, RF & LF
\
\
\
\
\
\
\

Master Cylinder (Bench Bleeding)
1) Bench bleed master cylinder before installation. Place
master cylinder in soft-jaw vise. Install bleeder tubes in both
outlets of master cylinder. See Fig. 1.
2) Fill master cylinder with clean brake fluid. Ensure ends
of bleeder tubes are submerged in brake fluid.
3) Using a wood dowel, apply and release master cylinder
until no air bubbles exist in brake fluid flow. Leave bleeder tubes
installed on master cylinder during installation. Install master
cylinder. Remove bleeder tubes, and connect brakelines. Bleed brake
system if necessary.

Page 356 of 1691

DODGE RAM 1999 Service Repair Manual CALIPER
CAUTION: DO NOT allow caliper to hang by brake hose. Damage to brake
hose could result.
Removal
Raise and support vehicle. Remove front wheels. Remove
cal

Page 357 of 1691

DODGE RAM 1999 Service Repair Manual ROTOR
CAUTION: DO NOT allow caliper to hang by brake hose.
Inspection
1) Raise and support vehicle. Remove wheels. On Dakota 4WD,
reinstall and tighten lug nuts to secure

ROTOR
CAUTION: DO NOT allow caliper to hang by brake hose.
Inspection
1) Raise and support vehicle. Remove wheels. On Dakota 4WD,
reinstall and tighten lug nuts to secure rotor. On Dakota 2WD, Ram
Pickup and Ram Van, remove dust cap, and temporarily adjust wheel
bearings to zero end play.
2) On all models, mount dial indicator on steering arm, with
plunger contacting rotor about 1" (25 mm) from edge of rotor. Slowly
rotate rotor, and note lateral runout. Lateral runout on either side
of rotor should not exceed specification. See DISC BRAKE
SPECIFICATIONS.
3) On Dakota, check runout of hub face if runout exceeds
specification. Before removing rotor, make a chalk mark across rotor
and one wheel stud. Make mark on high side of runout.
4) Remove rotor from hub. Install dial indicator on steering
arm, with stem contacting hub face near outer diameter. Place dial
indicator stem outside stud circle but inside chamfer on hub rim. If
runout exceeds specification See DISC BRAKE SPECIFICATIONS. Hub must
be replaced.
5) If hub runout is within specification, install rotor on
hub with chalk marks 180 degrees apart. Install wheel lug nuts, and
recheck rotor runout. If runout is not within specification, resurface
or replace rotor.
6) On all models, measure rotor parallelism. To measure
parallelism, measure rotor thickness with micrometer at 12 equal
points around rotor radius approximately 1" (25 mm) from edge of
rotor. If thickness varies more than parallelism specification,
resurface or replace rotor. See DISC BRAKE SPECIFICATIONS.
Removal (Dakota 2WD, Ram Pickup 2WD (5 Studs), & Ram Van)
Raise and support vehicle. Remove wheels. Remove brake
caliper from adapter. Support caliper aside. Remove grease cap, cotter
pin, nut lock, nut, thrust washer and outer wheel bearing. Pull rotor
assembly off spindle.
Installation
1) Slide rotor assembly into position on spindle. Pack and
install outer wheel bearing, thrust washer and nut. While rotating
rotor and hub assembly, tighten wheel bearing nut to specification.
See TORQUE SPECIFICATIONS table.
2) Back off nut to release preload. Retighten nut finger
tight. Install nut lock and cotter pin. Coat inside of cap with
grease, and install cap. To complete installation, reverse removal
procedure.
Removal (Ram Pickup With Tapered Bearings)
1) Raise and support vehicle. Remove wheel. Remove brake
caliper and adapter. Support caliper aside. Remove grease cap and
driving hub snap ring. Remove drive hub and spacer.
2) On models with removable adapter hub, remove hub from
rotor. On models with one-piece hub and rotor assembly, remove grease
cap, cotter pin and bearing adjuster nut. Remove thrust washer and
outer wheel bearing. Remove rotor and hub assembly from spindle.
Installation
1) Apply liberal coat of wheel bearing grease to spindle.
Install hub and rotor on spindle. Pack and install outer bearing.
Install thrust washer and bearing adjuster nut. Tighten nut only
enough to remove end play at his time.
2) Install caliper. DO NOT seat caliper pistons and brake

Page 358 of 1691

DODGE RAM 1999 Service Repair Manual pads at this time. On models with removable hub, install hub on rotor.
Install wheel and tire assembly. Tighten lug nuts so they are snug,
but DO NOT tighten to final torque specifications.
3

pads at this time. On models with removable hub, install hub on rotor.
Install wheel and tire assembly. Tighten lug nuts so they are snug,
but DO NOT tighten to final torque specifications.
3) While rotating wheel, tighten adjuster nut sufficiently to
seat bearing. Loosen nut and retighten while still rotating wheel.
Back off adjuster nut to completely release bearing preload torque.
Ensure endplay of .001-.003" (.025-.076 mm). Install lock nut and NEW
cotter pin. If necessary, tighten lock nut slightly to align cotter
pin hole. Install grease cap. Tighten caliper bolts and lug nuts to
specification. See TORQUE SPECIFICATIONS table. To complete
installation, reverse remove procedure.
Removal (Ram Pickup With 8 Studs)
1) Raise and support vehicle. Remove wheel. Remove hub
extension, if equipped. Remove brake caliper. Support caliper aside.
2) On models with removable adapter hub, remove hub from
rotor. On models with one-piece hub and rotor assembly, remove cotter
pin from rotor hub nut. Remove nut. Disconnect ABS wheel speed sensor
wire (if equipped), and remove from frame and steering knuckle. Remove\
bolts securing hub to steering knuckle from inboard side of steering
knuckle. Remove rotor and hub assembly.
Installation
1) Apply anti-seize compound to drive shaft splines. Replace
grease seal in steering knuckle, if necessary. Insert 2 rearmost top
and bottom rotor hub bolts in steering knuckle so they extend through
back of knuckle. Install hub spacer, ensuring flat on space is
positioned to rear. Use chassis grease to hold spacer in position, if
necessary.
NOTE: If equipped with wheel speed sensor, brake shield must be
positioned on hub bearing, and sensor wire must be at top of
knuckle.
2) Align rotor hub with drive shaft and install hub assembly.
Align bolt holes in hub flange with bolts previously installed. Start
nuts on flange bolts sufficiently to hold assembly in place. Install
remaining bolts, and tighten all bolts to specification. See TORQUE
SPECIFICATIONS table.
3) Install washer and hub nut. Tighten nut securely. Install
NEW cotter pin. Install grease cap. Install caliper. Tighten caliper
bolts and lug nuts to specification. See TORQUE SPECIFICATIONS table.
To complete installation, reverse remove procedure.
REAR BRAKE SHOES
WARNING: Use water or brake cleaner to clean brake parts. DO NOT use
compressed air to remove dirt and dust.
Removal (Dakota & Ram Van)
1) Remove wheel and drum. Note how secondary spring overlaps
primary return spring. Using spring remover, remove brake shoe return
springs. Slide automatic adjuster cable off anchor. Disconnect cable
from adjusting lever.
2) Remove cable, cable guide and anchor plate. See Figs. 3,
4, and 5. Disconnect adjusting lever return spring from lever. Remove
lever and return spring from pivot pin. Remove shoe-to-shoe spring.
Spread shoes, and remove adjustment star wheel.
3) Remove shoe retainers, springs and pins. Remove parking
brake lever from secondary shoe. Remove shoes and parking brake strut
with spring.

Load next 8 pages

Page: 1-8 9-16 17-24 next >

set clock child seat wheel bolts adblue instrument cluster flat tire