1998 TOYOTA LAND CRUISER window

H04756
H21413
H21410
H21411
- BODYFRONT DOOR
BO-1 1
2585 Author
: Date
:
2004 LAND CRUISER (RM1071U)
16. REMOVE WINDOW REGULATOR
(a) Disconnect the connector, then remove the 5 bolts.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
(b) Loosen the bolt and the window regulator.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
HINT:

Remove the regulator through the service hole.

At the time of reassembly, apply MP grease to the window
regulator.
NOTICE:
At the time of reassembly, do not apply grease to the spring
of the window regulator.
17. REMOVE DOOR LOCK
(a) Remove the clip and the door lock link protector.
(b) Disconnect the connector.
(c) Disconnect the 2 links from the outside handle and the
door lock cylinder.
(d) Using a torx wrench, remove the 3 screws and the door
lock through the service hole.
Torx wrench: T30 (Part No. 09042-00010 or locally
manufactured tool)
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
HINT:
At the time of reassembly:

Apply adhesive to the 3 screws.
Part No. 08833-00070, THREE BOND 1324 or equiva-
lent.

Remove the protector, and apply MP grease to the sliding
and rotating parts of the door lock.
18. REMOVE OUTSIDE HANDLE WITH DOOR LOCK CYL-
INDER
(a) Remove the 2 bolts and the outside handle with the door
lock cylinder.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
(b) Remove the bolt and the door lock cylinder from the out-
side handle.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)

BO1LD-03
H18905
Rear Door Opening TrimRoof Headlining Rear Trim
Upper Roof Side
Inner Garnish
Quarter Trim Jack CoverStriker Plate
Quarter Trim Panel Rear Door Scuff PlateQuarter Belt MouldingRear Mat
Rear Mat Set Plate Quarter Window
GlassStriker Plate Quarter Window
Glass Weatherstrip
Striker Plate
x5 Rear
Assist Grip Rear Vent Window Motor
Assist Grip
Plug
Assist Grip
Plug
- BODYQUARTER WINDOW GLASS
BO-61
2635 Author
: Date
:
2004 LAND CRUISER (RM1071U)
QUARTER WINDOW GLASS
COMPONENTS

BO1LF-02
BO-64
- BODYQUARTER WINDOW GLASS
2638 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-62).

BO4IW-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips BO-62
- BODYQUARTER WINDOW GLASS
2636 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATE
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATE
9. REMOVE REAR DOOR OPENING TRIM
10. REMOVE QUARTER TRIM PANEL
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel, then disconnect the con-
nector.
11. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHOR
12. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHOR

H18906
: 9 Clips
H04108
H05403
Quarter Belt
Moulding
Clip
: 4 Clips
H04110
- BODYQUARTER WINDOW GLASS
BO-63
2637 Author
: Date
:
2004 LAND CRUISER (RM1071U)
13. REMOVE UPPER ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the assist grip plugs, then re-
move the 2 screws and the rear assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape the screwdriver tip before use.
14. REMOVE QUARTER WINDOW GLASS
(a) Disconnect the connector.
(b) w/ Antenna:
Disconnect the connector.
(c) Remove the 2 bolts, the 2 nuts and the quarter window
glass.
15. REMOVE QUARTER WINDOW GLASS WEATH-
ERSTRIP
16. REMOVE QUARTER BELT MOULDING
(a) Remove the screw.
(b) Using a screwdriver, remove the quarter belt moulding.
HINT:
Tape up the screwdriver tip before use.
17. REMOVE REAR VENT WINDOW MOTOR
Remove the screw and the rear vent window motor.
18. REMOVE QUARTER WINDOW LOCK
Remove the screw and the quarter window lock.

BO1JE-03
H20973
Quarter Window Glass
with WeatherstripDivision Bar
Door Glass Run
Door Glass Door Belt Moulding
Service Hole Cover
Door Inside
Handle Bezel No. 1Inside Handle
Power Window
Switch Door Lock Outside Handle
Window Regulator
Door Courtesy Light
Door TrimDoor CheckDoor Hinge
Speaker
Door Hinge
: Specified torque
N´m (kgf´cm, ft´lbf)

Precoated part
27 (275, 20)
26 (265, 19)
5.0 (51, 44 in.´lbf)

8.0 (82, 71 in.´lbf)
26 (265, 19)
8.0 (82, 71 in.´lbf)
Door Inside
Handle Bezel No. 2
Door Check
Cover
23 (235, 17)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
8.0 (82, 71 in.´lbf)
23 (235, 17)
BO-14
- BODYREAR DOOR
2588 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR DOOR
COMPONENTS

BO1JF-03
H21407
H21408
H04820
H04752
H04822
: Clip
- BODYREAR DOOR
BO-15
2589 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE DOOR INSIDE HANDLE BEZEL No. 2
Using a screwdriver, remove the door inside handle bezel No.
2 as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE DOOR INSIDE HANDLE BEZEL No. 1
(a) Remove the screw.
(b) Using a screwdriver, remove the door inside handle bezel
No. 1 as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
3. REMOVE POWER WINDOW SWITCH
(a) Using a screwdriver, remove the power window switch as
shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(b) Disconnect the connector.
4. REMOVE DOOR COURTESY LIGHT
Using a screwdriver, remove the door courtesy light, then dis-
connect the connector.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE DOOR TRIM
(a) Remove the 3 screws and 4 clips.
(b) Insert a screwdriver between the door and door trim to pry
the trim.
NOTICE:
Be careful not to damage the door and door trim.
HINT:
Tape up the screwdriver tip before use.
(c) Pull the trim upward to remove it.

H21409
H04823
H04824
H04825
H04826
BO-16
- BODYREAR DOOR
2590 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6. REMOVE INSIDE HANDLE
(a) Remove the screw and the inside handle.
(b) Disconnect the 2 control cables from the inside handle as
shown in the illustration.
7. REMOVE SPEAKER
Remove the 3 screws and speaker, then disconnect the con-
nector.
8. REMOVE SERVICE HOLE COVER
(a) Remove the clamps and wire harness.
(b) Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, bring out the 2 control cables and
wire harness through the service hole cover.
9. REMOVE DOOR BELT MOULDING
Using a scraper, remove the door belt moulding.
HINT:
Tape up the scraper tip before use.
10. REMOVE DOOR GLASS RUN
11. REMOVE DIVISION BAR
Remove the 2 bolts, screw and division bar.
12. REMOVE DOOR GLASS
Disconnect the glass from the regulator arm and remove the
door glass by pulling it upward.
13. REMOVE QUARTER WINDOW GLASS WITH WEATH-
ERSTRIP
14. REMOVE WINDOW REGULATOR
(a) Disconnect the connector, then remove the 3 bolts.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
(b) Loosen the bolt and window regulator.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
HINT:

Remove the regulator through the service hole.