1998 TOYOTA LAND CRUISER ECO mode

D14352
Overflow Tube
AT-3-3
- AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION SYSTEM
1857 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Without hand-held tester (Using A/T OIL TEMP indicator)
(1) Connect terminals between CG (4) and TC (13) of
the DLC3 using SST (09843-18040).
(2) Move the shift lever back and forth between N and
D at 1.5 seconds interval for six seconds.
(3) The D shift indicator on the combination meter
comes on for two seconds. This indicates that the
fluid temperature check mode has been started.
(4) The D shift indicator comes on again when the fluid
temperature reaches 46C (115F) and blinks
when it exceeds 56C (130F).
(5) Allow the engine to idle until the fluid temperature
reaches 46C (115F).
6. FLUID LEVEL CHECK
NOTICE:
The fluid temperature must be between 46C (115F) and
56C (130F) to check the fluid level.
(a) Remove the overflow plug with the engine idling.
(b) Check that the fluid comes out of the overflow tube.

If fluid does not come out, proceed to step 7.

If fluid comes out, wait until the overflow slows to a
trickle and proceed to step 8.
7. TRANSMISSION REFILL
(a) Install the overflow plug.
(b) Stop the engine.
(c) Remove the refill plug.
(d) Add 0.4 liters (0.42 US qts, 0.35 lmp. qts) of fluid.
(e) Allow the engine to idle and wait for 10 seconds.
(f) Proceed to step 6.
8. COMPLETE
(a) Install the overflow plug with a new gasket.
(b) Stop the engine.
(c) Install the refill plug with a new gasket.
Torque:
20 NVm (205 kgfVcm, 15 ftVlbf) for overflow plug
39 NVm (400 kgfVcm, 29 ftVlbf) for refill plug

BE0SD-04
I06143
6 3
I06144
6 3
I24666
Integration panel control assembly
- BODY ELECTRICALANTENNA
BE-175
2548 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. Auto Antenna Models:
INSPECT ANTENNA MOTOR
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (-) lead to terminal 6.
(b) Check that the motor turns (moves upward).
NOTICE:
These tests must be done quickly (within 3 - 5 seconds) to
prevent the coil from burning out.
(c) Then, reverse the polarity, check that the motor turns the
opposite way (moves downward).
NOTICE:
These tests must be done quickly (within 3 - 5 seconds) to
prevent the coil from burning out.
2. INSPECT ANTENNA SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
UP button FREE4 - 5No continuity
UP button Pushed in4 - 5Continuity
DOWN button FREE9 - 5No continuity
DOWN button Pushed in9 - 5Continuity
If continuity is not as specified, replace the switch.

Physical address: 190 Radio receiver assembly
Diagnosis item
ROM Error
Absence of
MasterDiagnosis contentCountermeasure and
inspected parts
Error is detected in internal ROM. Logical address
01
(Communication
Control)
01 *2
(Communication
Control)Component in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected.
Check harness for power supply
system of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly.
DTC
21
D6Replace radio receiver assembly.
RAM Error Error is detected in internal RAM. 01
(Communication
Control)22Replace radio receiver assembly.
No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON.
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control)
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.

If error occurs again, replace
component shown by auxiliary
code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected.
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.
- BODY ELECTRICALAUDIO SYSTEM
BE-141
2514 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. DIAGNOSIS CODE LIST
w/ Navigation system (See page)

No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON.
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control)
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.

If error occurs again, replace
component shown by auxiliary
code.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected.
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.
Physical address: 16A, 16C RSA Panel (Sub AVC-LAN)
Transmission
Error DC 01 *4
(Communication
Control)Transmission to component shown
by auxiliary code has been failed.
(Detecting this DTC does not nec-
essary mean actual failure.)
If same auxiliary code is recorded
in other component, check harness
for power supply and communica-
tion system of components shown
sub code.
Slave Reset
(Momentary
Interruption) DE 01 *3
(Communication
Control)After engine is started, slave com-
ponent was disconnected from sys-
tem.
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
BE-146
- BODY ELECTRICALAUDIO SYSTEM
2519 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BE1Z9-01
Mode Select Switch
On Duration
Normal Mode
Pressed for 3 sec.
6. Compass Non-display Mode
Pressed for 6 sec.
7. Zone Setting ModeIgnition switch ON.
Pressed for 9 sec.
Zone area +1 Mode Select Switch ON
8. Calibration Mode
Leaving it untouched
for a while
Normal Mode
- BODY ELECTRICALCOMPASS
BE-71
2444 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMPASS
PRE-CHECK
1. SELECTING COMPASS DISPLAY MODE
The mode select switch allows you to select a Display or Non-display mode of the compass.
The mode select is operated by the automatic glare-proof / non-glare proof switch on the inner mirror.
2. SETTING ZONE
Deviation between the magnetic north and ºactual northº differs depending on the terrestrial location, there-
fore, an adjustment in magnetism is required. Since the magnetic condition differs according to the area
where the vehicle will be used, it is necessary for each user to set the zone. (Refer to ºCompass Zone Mapº).
The zone setting can be changed using the mode select switch of the inner mirror.
3. PERFORMING CALIBRATION
Because each vehicle has its own magnetic field, calibration should be performed for each vehicle. This com-
pass function is used when storing the record of the vehicle's magnetic field.
4. WHEN COMPASS MAGNETIZED:
A compass could be magnetized during shipping by vessels or freight cars. Before delivery, therefore, make
sure to perform calibration and ensure that calibration can be done. If it cannot be done (cannot complete
in spite of driving round several times), it may be caused by magnetization. Demagnetize the vehicle using
a demagnetizer and perform calibration again.
5. SETTING COMPASS

- BODY ELECTRICALCOMPASS
BE-73
2446 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Pressing the mode select switch for 6 sec. from the normal mode will activate the zone setting mode, showing
a numbar (1-15) on the compass display.
HINT:
In the initial status, º8º is displayed.
(1) The displayed number increases +1 every time the mode select switch is pressed. Referring to
the map, check the number for the area where the vehicle will be used and set the zone number.
(2) Leave it untouched for several seconds after setting and check that the compass display shows
an azimuthal direction (N, NE, E, SE, S, SW, W, or NW) or ºCº.
8. CALIBRATION SETTING MODE
(a) After the set zone is displayed, if the switch remains pressed another 3 sec. will activate the calibration
setting mode.
(b) Pressing the switch for 9 sec. from the normal mode will also activate this mode.
(c) Drive the vehicle at a slow speed of 8 km/h (5MPH) or less in the circular direction.
(d) Driving round the circle 1 to 3 times will display the azimuthal direction on the display, completing the
calibration.
HINT:
Once calibration is completed, it is not necessary to perform the above procedures unless the magnetic field
strength is drastically changed. If this happens, the azimuthal display will be changed to ºCº.

I03487
GARAGE DOOR
OPENER SWITCH
LEARN MODE
LED
OPERATION
ORIGINAL
TRANSMITTERPRESSED
ENTER
EXIT
ON
OFF20 sec
LED flashes
at a rate of 1 Hz
LED flashes at a
rate of 5.6 Hz PRESSED
ON
OFF
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE-187
2560 Author
: Date
:
2004 LAND CRUISER (RM1071U)
New code registration timing chart
If a code can not be registered, observe the following condi-
tions.
HINT:

If the battery of original transmitter is consumed.

Press the switch of the transmitter repeatedly in registra-
tion mode, as some transmitters stop transmitting for 1 to
2 seconds.

This system is not applicable to the garage door opener
which had been made before 1982.
2. CODE DELETION
(a) Press the switches at both ends of garage door opener
simultaneously for 20 seconds.
HINT:
When transferring to deletion mode, LED (red) blinks in 6 Hz
cycle.
(b) When releasing the switch within 10 seconds after trans-
ferring to deletion mode, all the registered codes will be
erased.
HINT:
Press the switch until blinking in 6 Hz cycle stops, so that the
default code for check is set.

BE2F2-01
I20790
Key Plate Inserted
ON
OFFWithin. 5secs.
1 Key Plate Not Inserted
23 910Within. 30secs.
Once 9 times BE-100
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2473 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. CHARACTERS OF WIRELESS DOOR LOCK
(a) The operation distance changes according to how cus-
tomers hold the transmitter or where it is used.
(b) Because of using the very weak radio wave, if there is a
strong wave or noise on the frequency being used, the op-
eration distance may become shorter.
2. WIRELESS DOOR LOCK BASIC FUNCTION
(a) Stand on the driver's side. Stay 1 m away from the ve-
hicle.
(b) Turn the transmitter toward the vehicle and press any one
of the transmission switched for 1 sec.
3. INSPECT WIRELESS DOOR LOCK DIAGNOSIS MODE
(a) Start up diagnosis mode.
HINT:
Follow the method below.
(1) Insert the ignition key into the ignition key cylinder.
(2) Remove the ignition key from the ignition key cylin-
der.
(3) Insert the key into the ignition switch.
(4) Turn the ignition switch ON once within 5 sec.
(5) Repeat turnning the ignition switch OFF " ON 9
times within 30 sec.
(6) Enter the diagnosis mode, and make sure that the
taillight lights up.
(b) Finishing the Diagnosis Mode.
During the Diagnosis mode, turn the ignition switch OFF
" ON to go back to the normal mode.
At this time make sure that the taillight lights up.