1998 TOYOTA LAND CRUISER window

BE0TF-05
I24746
Power Window Master Switch
Power Window Switch
Power Window Regulator Assembly

Power Window Motor

Limit Switch

Pulse Switch Power Window Regulator Assembly

Power Window Motor

Limit Switch

Pulse Switch
Ignition Switch
Cowl Side J/B RH

P/W (FL/RL) Fuse

P/W (FR/RR) Fuse
BE-78
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
2451 Author
: Date
:
2004 LAND CRUISER (RM1071U)
POWER WINDOW CONTROL SYSTEM
LOCATION

BE-8
- BODY ELECTRICALTROUBLESHOOTING
2381 Author
: Date
:
2004 LAND CRUISER (RM1071U) ECT PWR indicator light does not light up.
1. LED
2. ECT Pattern Select Switch
3. Combination Meter
4. Wire Harness
5. ECT System-
-
BE-58
-
DI-358
2nd start ETCS indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1
Center Diff. lock indicator light does not light up.
1. LED
2. Combination Meter
3. Transfer 4WD Position Detection Switch
4. Wire Harness-
BE-58
TR-49
-
Indicator lights do not light up. (Except Turn, Hi-beam and
security)1. GAUGE2 Fuse
2. Wire Harness-
-
DEFOGGER SYSTEM:
SymptomSuspect AreaSee page
All defogger systems do not operate.
1. DEFOG Fuse
2. DEFOG Relay
3. Defogger Switch (Integration Control Panel Assembly)
4. Wire Harness-
-
BE-75
-
Rear window defogger does not operate.
1. Defogger Wire
2. Choke Coil
3. Wire HarnessBE-75
-
-
Mirror defogger does not operate.
1. MIR HTR Fuse
2. Engine Room J/B Relay Circuit
3. Mirror Defogger
4. Wire Harness-
BE-15
BE-75
-
POWER WINDOW CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the power windows do not operate.
(Power Door Lock System is normal.)1. P/W (FL, FR, RL, RR) Fuse
2. Power Window Master Switch
3. Wire Harness-
BE-79
-
Only the driver's window does not operate.
1. Power Window Master Switch
2. Body ECU
3. Power Window Motor
4. Wire HarnessBE-79
DI-1038
BE-79
-
ºWindow lock functionº does not operate.1. Power Window Master SwitchBE-79
POWER DOOR LOCK CONTROL SYSTEM:
This system uses the body control system, so check diagnosis system of the body control system before
you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the doors cannot be locked or unlocked.
(Power Window Control System is normal.)
1. DOOR Fuse
2. Door Lock Control Switch
3. Wire Harness
4. Body ECU-
BE-88
-
DI-1038
Only one side door lock control does not operate.1. Door Lock Motor
2. Wire HarnessBE-88
-

BO1KA-02
H06468
Back Door Glass

Spacer
Back Window Outside Moulding
Center Back Door Garnish
Back Door Garnish
Assist Grip
Assist Grip Plug
Inside Handle Bezel
Rear Wiper Arm
Clip

Spacer
Clip
5.4 (55, 48 in.´lbf): Specified torqueN´m (kgf´cm, ft´lbf)

Non-reusable part
- BODYBACK DOOR GLASS
BO-65
2639 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BACK DOOR GLASS
COMPONENTS

H04079
H02865
Primer M
Primer M
Adhesive
H04080
a
a
a-a
Primer G
- BODYBACK DOOR GLASS
BO-69
2643 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4. INSTALL BACK WINDOW MOULDING
Install a new back window moulding as shown in the illustration.
NOTICE:
Do not touch the glass face after cleaning it.
5. COAT CONTACT SURFACE OF DOOR PANEL WITH
PRIMER ºMº
Using a brush, coat Primer M to the exposed part of door panel
on the vehicle side.
NOTICE:

Let the primer coating dry for 3 minutes or more.

Do not coat Primer M to the adhesive.

Do not keep any of the opened Primer M for later use.
6. COAT CONTACT SURFACE OF GLASS WITH PRIMER
ºGº
(a) Using a brush or sponge, coat the edge of the glass and
contact surface with Primer G.
(b) When the primer coated wrongly to the area other than
the specified, wipe it off with a clean shop rag before the
primer dries.
NOTICE:

Let the primer coating dry for 3 minutes or more.

Do not keep any of the opened Primer G for later use.

H04081
a
A
B a
a-a
H04848
: 10 Clips BO-70
- BODYBACK DOOR GLASS
2644 Author
: Date
:
2004 LAND CRUISER (RM1071U)
7. APPLY ADHESIVE
(a) Cut off the tip of the cartridge nozzle.
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the table below.
TemperatureTackfree time
35 °C (95 °F)15 minutes
20 °C (68 °F)100 minutes
5 °C (41 °F)8 hours
(b) Load the cartridge into the sealer gun.
(c) Coat the glass with adhesive, as shown in the illustration.
A: 8.0 mm (0.315 in.)
B: 12.0 mm (0.472 in.)
8. INSTALL BACK DOOR GLASS
(a) Install the glass to the body.
(b) Hold back window glass in place securely with protective
tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to moving a car
35 °C (95 °F)1.5 hours
20 °C (68 °F)5 hours
5 °C (41 °F)24 hours
9. INSPECT FOR LEAKS AND REPAIR
(a) Conduct a leak test after the hardening time has elapsed.
(b) Seal any leak with sealant.
Part No. 08833-00030 or equivalent.
10. INSTALL REAR WIPER ARM (See page BO-42)
11. INSTALL BACK DOOR GARNISH

BO21B-01
H04847
: 9 Clips
ba
a - a
b - b
ab
H04848
: 10 Clips
H04076
BO-66
- BODYBACK DOOR GLASS
2640 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ASSIST GRIP
(a) Using a screwdriver, remove the 2 assist grip plugs.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and assist grip.
2. REMOVE INSIDE HANDLE BEZEL
3. REMOVE CENTER BACK DOOR GARNISH
Using a screwdriver, remove the center back door garnish.
HINT:
Tape the screwdriver tip before use.
4. REMOVE BACK DOOR GARNISH
Using a screwdriver, remove the back door garnish.
HINT:
Tape the screwdriver tip before use.
5. REMOVE REAR WIPER ARM (See page BO-38)
6. REMOVE OUTSIDE BACK WINDOW MOULDING
Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Do not damage the body with the knife.

BO1JA-04
H20972
Door Glass Run Door Glass
Outside Handle
Door Lock Cylinder
Door Lock
Window RegulatorLower FrameDoor Belt Moulding
Tweeter Speaker
Lower Frame
Bracket Garnish Outside Rear View Mirror
Service
Hole Cover Door Inside
Handle Bezel
No. 1Inside Handle
Door Courtesy Light
Door TrimSpeaker
Door Hinge Door Check
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
26 (265, 19)
26 (265, 19)


: Specified torqueN´m (kgf´cm, ft´lbf)

Precoated part
8.0 (82, 71 in.´lbf)
27 (275, 20)
5.0 (51, 44 in.´lbf)
Power Window Switch
Door Lock Link
Protector
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)Door Inside
Handle Bezel No. 2
Door Check Cover
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)
5.0 (51, 44 in.´lbf)
23 (235, 17)
23 (235, 17)
BO-8
- BODYFRONT DOOR
2582 Author
: Date
:
2004 LAND CRUISER (RM1071U)
FRONT DOOR
COMPONENTS

BO1JB-03
H04748
:2 Clips
H04749
H21407
H21408
H04752
- BODYFRONT DOOR
BO-9
2583 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE LOWER FRAME BRACKET GARNISH
Using a screwdriver, remove the lower frame bracket garnish.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE POWER WINDOW SWITCH
(a) Using a screwdriver, remove the power window switch as
shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(b) Disconnect the connector.
3. REMOVE DOOR INSIDE HANDLE BEZEL No. 2
Using a screwdriver, remove the door inside handle bezel No.
2 as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE DOOR INSIDE HANDLE BEZEL No. 1
(a) Remove the screw.
(b) Using a screwdriver, remove the door inside handle bezel
No. 1 as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE DOOR COURTESY LIGHT
Using a screwdriver, remove the door courtesy light, then dis-
connect the connector.
HINT:
Tape up the screwdriver tip before use.