1998 JAGUAR X308 warning

Front Suspension - Fron
t Shock Absorber
Re
moval and Installation
Remov

al
S
pecial Tool(s)

Front Camber Tie-do

wn Link
204-114 (JD 133)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-0
0 General
Informati

on
.
R
aise the front of the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.

2.
Ful
ly slacken the adjuster nut of the special tool 204-114 and
position in the center of the road spring.

3. W
ARNING: ENSURE THAT THE DOWEL OF THE SPECIAL
TOOL 204-114 IS CORRECTLY POSITIONED ACROSS THE
SUSPENSION TURRET SLOT.
Locate the special tool in the suspension turret slot.
Pass
the upper dowel through the slot in the suspension
turret and rotate to locate the dowel.
4. Lower the front o
f
the vehicle.
5. WARNING: WHEN TIGHTENING THE TOOL NUT, USE THE
LOWER DOWEL AS A GUIDE TO ENSURE THAT THE TOOL STEM
DOES NOT ROTATE AND DISTURB THE POSITION OF THE DOWEL
IN THE SUSPENSION TURRET.
Tighten the nut of the special tool 204-114 to its full extent, to
achieve a suspension mid-laden position.

2. Ins
tall Special Tool 204-111 and spring assembly in suspension

turret.
P
osition spring assembly and Special Tool in suspension
turret.
Ensure spri
ng upper rubber se
at is correctly positioned
and fully seated.
Engage tool
dowel in turret slot.

3. Position spr
ing pan on lower wishbone.
Ro

tate adjuster of Special Tool to lightly tension spring.
Al

ign spring pan with lower wishbone bolt locations.

4. Inst
all suitable guide pins in
spring pan/wishbone bolt
locations.
5. WARNING: WHEN ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Install spring pan to wishbone securing bolts.

Rot
ate tool adjuster to gradua
lly increase spring tension.
Pr
ogressively substitute spri
ng pan securing bolts for
guide pins.
Ti ghten spring pan
securing bolts to 70-90Nm.

6. WARNING: WHE N
ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Remove Special Tool 204-111 from suspension.
Ensure spri ng
lower rubber seat
is correctly positioned and
fully seated.
R otat
e adjuster of Special Tool to release tension on
spring.

7. Ro
tate tool stem to release
dowel from turret and withdraw
tool assembly.
8. Lower vehicle to working heig ht and support on stands.
9. Install road wheel. Re fer to Section 100-02.
10. Raise vehicle, remove stands and lower vehicle onto road
wheels.

2. Ins
tall Special Tool 204-111 and spring assembly in suspension

turret.
P
osition spring assembly and Special Tool in suspension
turret.
Ensure spri
ng upper rubber se
at is correctly positioned
and fully seated.
Engage tool
dowel in turret slot.

3. Position spr
ing pan on lower wishbone.
R

otate adjuster of Special Tool 204-111 to lightly tension
spring.

4. Install guide pins ( su
pplied wi
th Special Tool 204-111) in
spring pan/wishbone bolt locations.
5. WARNING: WHEN ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Install spring pan to wishbone securing bolts.

Align sp
ring pan with lower wishbone bolt locations.
Rot

ate tool adjuster to gradua
lly increase spring tension.
P
r
ogressively install but do no
t tighten spring pan securing
bolts.
Ti ghten spring pan
securing bolts to 70-90Nm.
Ensure spri
ng
lower rubber seat is correctly positioned in
spring pan.

6. WARNING: WHE N
ROTATING TOOL ADJUSTER, ENSURE
THAT TOOL STEM DOES NOT TU RN AND DISTURB POSITION OF
DOWEL IN SUSPENSION TURRET.
Remove Special Tool 204-111 from suspension.
Rotat
e adjuster of Special Tool to release tension on
spring.
R otate
tool stem to release dowel from turret.
With
draw tool and adaptor
.assembly.
7.
Lower vehi cle to work
ing heig
ht and support on stands.
8. Install road wheel. Re fer to Section 100-02.
9. Raise vehicle, remove stands and lower vehicle onto road
wheels.
10. Carry out steering geometry an d wheel alignment checks and
if necessary adjust. Refer to 57.65.01.
11. Carry out steering geometry an d wheel alignment checks and
if necessary adjust. Refer to 57.65.01.

Front Suspension - Upper Arm Bushing
Re
moval and Installation
Remov

al
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
S
pecial Tool(s)

Ball

Joint Taper Separator
204-192 (JD 219)

Front Camber Tie-do
wn Link
204-114 (JD 133)
1. R
aise front of vehicle.
Refer to Section 100-02.

2. P
osition camber tie down spec
ial tool 204-114 on suspension.
Fully s
lacken tool adjuster nut.
Position too

l in road spring and pass upper dowel through
slot in suspen sion turret.
3. Lower front of vehicle.

4. R
otate stem of special tool 204-114 to locate dowel in
suspension turret slot.
5. WARNING: WHEN TIGHTENING TOOL NUT, USE LOWER
DOWEL AS A GUIDE TO ENSURE THAT THE TOOL STEM DOES
NOT ROTATE AND DISTURB POSITION OF DOWEL IN
SUSPENSION TURRET.
Fully tighten nut of special tool to achieve suspension mid-laden

Front Susp
ension - Wheel Knuckle and Wheel Hub Assembly
Re
moval and Installation
Remov

al
S
pecial Tool(s)

R

oad spring compressor
204-111 (JD115)

Taper separator

211-098 (JD 100)

Front
suspension ball joint splitter
204-192 (JD 219)

Bal
l joint splitter
204-293
1. Raise front of vehicle and support on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to 74.20.05.
3. Remove brake disc. Refer to 70.10.12.
4. Using wire or string, secure brak e caliper to road spring to take
weight off brake hose.
5. Raise vehicle sufficient to provide access for special tool 204-
111.

6. Ins
tall special tool 204-111 in road spring.
Sl

acken tool adjuster to suit spring length.
Fit adaptor and th

rust collar.
Posit

ion stem of tool in center of spring passing dowel
through slot in su spension turret.
7. WARNING: WHEN TURNING TOOL ADJUSTER, ENSURE

I
nstallation


18
.
WARNING: With assistance, support the rear suspension
and axle assembly during remo val. Failure to follow this
instruction may result in personal injury.
Remove the rear suspensi on and axle assembly.
E
nsure that the hydr
aulic pipes, brake calipers, harnesses
and the drive shaft will not obstruct the rear suspension
and axle assembly during removal.
Carefull
y lower the rear suspen
sion and axle assembly and
traverse clear of vehicle.

19
.
Retrieve the subframe mounting bush shims.
20. With assistance, position th e rear suspension and axle
assembly on to a bench.
21. Clean the subframe mounting bushes and corresponding body
locations.

1. Apply a th
in coat of grease to the subframe bushes and place
the shims in position.
2. WARNING: With assistance, support the rear suspension