1998 JAGUAR X308 wheel

28
.
Install the rear wheel.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.
29
.
Remove the axle stands and lower the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
30
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension
Sy

stem
- General
Information
.

Rear
Suspension - Rear Wheel Bearing
Re
moval and Installation
S

pecial Tool(s)

Hub Holdin

g Tool
204-195 (JD227)

Hub Pu
ller
204-011 (JD 1D)

R
ear-Hub Remover
204-113 (JD 132)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/1)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/2)

D
river Handle
100-013 (18G-134)

Rear-hub spacer
replacer
204-003 (JD 15)
O
il Seal Remover/Replacer

Remova
l

2
05-2
34 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release handbrake.
2. Ra
ise the vehicle on a four-post lift.

3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.

4. Relea s
e appropriate side parkin
g brake cable from connecting
clip.

5. With draw parkin
g brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. P
osition special tool 204-195 on hub studs and install securing
nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.

14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R

emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.

29. Tigh
ten pivot pin nut.
Al
ign mark
er on pivot pin flange with mark made on
wishbone.
Ensuri ng pi
n position is not
disturbed, tighten nut to 88-
118Nm.

30 . Inst
all wheel speed sensor on hub carrier.
Posit
i
on sensor on hub carrier
and install and tighten bolt
to 7-10Nm.
Connect
wheel speed sensor harness to sensor.

31 . Using new ti
e strap, secure wh
eel speed sensor harness to
hub carrier.
32. Install handbrake shoes. Re fer to operation 70.40.05.
33. Install brake disc. Refer to operation 70.10.13.
34. Position special tool 204-195 on hub studs and install
securing nuts.

35
.
Tighten hub nut to 304-336Nm.
36. Remove securing nuts and withdraw special tool 204-195
from hub.
37. Install rear wheel. Refer to Section 204-04.
38. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
39. Raise vehicle on four-post lift.

40
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

41
.
Route parking brake LH ca ble through equalizer.
42. Install LH cable in connecting clip.

43
. Adjust parkin
g brake cable. Refer to 70.35.10.
44. Lower four-post lift
45. Apply parking brake.
46. Carry out rear wheel alignm ent check and adjust as
necessary. Refer to data in Specification section.

Rear Suspension - Wheel Hub
Seal
Re
moval and Installation
Remov

al
S
pecial Tool(s)

Hub Holdin

g Tool
204-195 (JD227)

Hub Pu
ller
204-011 (JD 1D)

R
ear-Hub Remover
204-113 (JD 132)

O
il Seal Remover/Replacer
205-234 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release parking brake.
2. R
aise the vehicle on a four-post lift.

3. Fully
slacken but do not remove parking brake cable adjuster
nut.
4. Release appropriate side parkin g brake cable from connecting