1998 JAGUAR X308 clock

Exterior Lighting - Front Fog Lamp Bulb
Removal and Installation
Removal
Installation

1.
Remove undertray for ac cess. Refer to 76.22.90.

2. Disconnect fog lamp harness multiplug.

3. Rotate bulb holder 1/4 turn counter-clockwise to release and
remove from lamp assembly.
4. CAUTION: If bulb is to be re -fitted, the glass must not be
touched with the bare hand. Failure to observe this caution will
result in premature bulb failure.
Remove bulb from holder.
1. CAUTION: Fog lamp bulbs are of the halogen type and
must not be touched with bare hands. Failure to observe this
caution will result in premature bulb failure.
Install bulb in holder.
2. Install bulb holder in lamp assembly and rotate 1/4 turn
clockwise to fully seat and engage.
3. Connect fog lamp harness multiplug.
4. Install undertray. Refer to 76.22.90.

Exterior Lighting - Front Side Marker Lamp Bulb
Removal and Installation
Removal

1. Applying firm hand pressure to front end, pivot lamp assembly
for access to rear end.

2. Exercising care to avoid dama ging paintwork, use a small
screwdriver at rear end of lamp, to press and release retaining
tang.

3. Withdraw lamp from bumper for access and disconnect harness multiplug.

4. Rotate bulb holder 1/4 turn counter-clockwise to release it
from lamp assembly.
5. Withdraw bulb from holder.

Installation



1. Install bulb in holder.
2. Install bulb and bulb holder in lamp assembly and rotate 1/4
turn clockwise to seat and retain.
3. Position direction lamp at bumper aperture and connect
harness multiplug.
4. Engage front end tang of lamp in bumper aperture.
5. Pivot lamp assembly and firmly seat rear retaining clip in
bumper aperture.

Exterior Lighting - Rear Lamp Assembly Bulb
Removal and Installation
Removal
Installation

1. Depress retaining tab and remove rear lamp interior trim
finisher.

2. Disconnect rear lamp harness multiplug.

3. Rotate bulb holder retainin g fastener 1/4 turn counter-
clockwise and withdraw holder from rear lamp lens.

4. Remove bulbs from holder as necessary.
1. Install bulbs in holder as necessary.

Exterior Lighting - Rear Side Marker Lamp Bulb
Removal and Installation
Removal

1. Applying firm thumb pressure to front of lens, pivot lamp
assembly for access to rear end.

2. Exercising care to avoid dama ging paintwork, use a small
screwdriver to press and re lease rear retaining clip.

3. Withdraw lamp from bumper for access and disconnect harness connector.

4. Rotate bulb holder 1/4 turn counter-clockwise to release it
from lamp assembly.
5. Withdraw bulb from holder.

Installation



1. Install bulb in holder.
2. Install bulb and bulb holder in lamp assembly and rotate 1/4
turn clockwise to seat and retain.
3. Position lamp at bumper ap erture and connect harness
connector.
4. Engage front end tang in bumper aperture.
5. Pivot lamp assembly and firmly seat rear retaining clip in
bumper aperture.

Exterior Lighting - Side Lamp Bulb
Removal and Installation
Removal
Installation

1.
Open hood and install fender cover.

2. Rotate bulb holder 1/4 turn counter-clockwise and remove
from headlamp
3. Position bulb holder and harne ss for access and withdraw bulb
from holder.
1. Install parking/sidelamp bulb in bulb holder
2. Position bulb and holder in headlamp, and rotate 1/4 turn
clockwise to fully seat.
3. Remove fender cover and close hood.

Exterior Lighting - Side Turn Signal Lamp Bulb
Removal and Installation
Removal
Installation

1.
Remove indicator repeater lamp assembly. Refer to 86.41.41.

2. Remove lamp. Refer to this section.
Twist bulb holder anti-clockwise and remove.
Remove bulb and replace with new one of correct type.
1. Installation is reverse of removal.