1997 TOYOTA SUPRA brake pads

BR0GR-01
R07124
Z09010Z09010
R07127
BR-26
- BRAKEFRONT BRAKE PAD (2JZ-GTE)
1826 Author
: Date
:
1997 SUPRA (RM502U)
REPLACEMENT
1. REMOVE FRONT WHEEL
Remove the wheel and temporarily fasten the disc with the hub
nuts.
2. INSPECT PAD LINING THICKNESS
Check the pad thickness and replace pads if they are not within
specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE THESE PARTS
(a) Clip and 2 pins
(b) Anti-rattle spring
(c) 2 pads
(d) 2 pad spacers
(e) 2 anti-squeal shims
NOTICE:
The anti-rattle spring, clip and pad spacers can be used
again provided that they have sufficient rebound, no de-
formation, cracks or wear, and have had all rust, dirt and
foreign particles cleaned off.
4. CHECK DISC THICKNESS AND RUNOUT
(See page BR-39)
5. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pads.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the pistons with a hammer handle or equivalent.
HINT:

Always change the pads on one wheel at a time as there
is a possibility of the opposite piston flying out.

If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.

R11393
- BRAKEFRONT BRAKE PAD (2JZ-GTE)
BR-27
1827 Author
: Date
:
1997 SUPRA (RM502U)
(c) Install the anti-squeal shim on each pad.
HINT:

Place the pad wear indicator facing downward.

Apply disc brake grease to inner side of the anti-squeal
shims (See page BR-25).

Make sure that the arrow on the shims points upward.
(d) Install a pad spacer on the lower side of the each pad.
(e) Install the 2 pads.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
6. INSTALL ANTI-RATTLE SPRING AND 2 PINS
7. INSTALL CLIP

BR0GZ-01
R07130
R07131
- BRAKEFRONT BRAKE CALIPER (2JZ-GTE)
BR-37
1837 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
Remove the 2 mounting bolts and caliper.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
4. REMOVE THESE PARTS
(a) Clip and 2 pins
(b) Anti-rattle spring
(c) 2 pads
(d) 2 pad spacers and anti-squeal shims

BR0H7-01
R07147
Z09011
R07150
BR-46
- BRAKEREAR BRAKE PAD (2JZ-GTE)
1846 Author
: Date
:
1997 SUPRA (RM502U)
REPLACEMENT
1. REMOVE REAR WHEEL
Remove the wheel and temporarily fasten the disc with the hub
nuts.
2. INSPECT PAD LINING THICKNESS
Check the pad thickness and replace pads if they are not within
specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE THESE PARTS
(a) Clip and 2 pins
(b) Anti-rattle spring
(c) 2 pads
(d) 4 anti-squeal shims
NOTICE:
The anti-rattle springs and clip can be used again provided
that they have sufficient rebound, no deformation, cracks
or wear, and have had all rust, dirt and foreign particles
cleaned off.
4. CHECK DISC THICKNESS AND RUNOUT
(See page BR-57)
5. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pads.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the pistons with a hammer handle or equivalent.
HINT:

Always change the pads on one wheel at a time as there
is a possibility of the opposite piston flying out.

If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.

R11394
- BRAKEREAR BRAKE PAD (2JZ-GTE)
BR-47
1847 Author
: Date
:
1997 SUPRA (RM502U)
(c) Install the 2 anti-squeal shims on each pad.
HINT:

Apply disc brake grease to both sides of the inner anti-
squeal shim (See page BR-45).

Make sure that the arrow on the shims points upward.
(d) Install the 2 pads with pad wear indicator plates facing
downward.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
6. INSTALL ANTI-RATTLE SPRING AND 2 PINS
7. INSTALL CLIP

BR0HF-01
R07153
R07154
- BRAKEREAR BRAKE CALIPER (2JZ-GTE)
BR-55
1855 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE REAR WHEEL
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
(b) Use a container to catch the brake fluid.
3. REMOVE CALIPER
Remove the 2 mounting bolts and caliper.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
4. REMOVE THESE PARTS
(a) Clip
(b) 2 pins
(c) Anti-rattle spring
(d) 2 pads
(e) 4 anti-squeal shims

B03050
MA01H-01
MA-6
- MAINTENANCEBRAKE
43 Author
: Date
:
1997 SUPRA (RM502U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check all brake lines and hoses for:

Damage

Wear

Deformation

Cracks

Corrosion

Leaks

Bends

Twists
(b) Check all clamps for tightness and connections for leak-
age.
(c) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT AND REAR BRAKE PADS AND
DISCS
2JZ-GE:
Front: See page BR-23
Rear: See page BR-43
2JZ-GTE:
Front: See page BR-26
Rear: See page BR-46
HINT:
If a squealing or scraping noise comes from the brake during
driving, check the pad wear indicator to see if it is contacting the
disk rotor. If so, the disk pad should be replaced.
3. INSPECT PARKING BRAKE LININGS AND DRUMS
(See page BR-62)