1997 TOYOTA SUPRA airbag

H03221
P squibAirbag Sensor
Assembly
D squib
Spiral
Cable
ACC
ON
E
1Tc DLC1 Code 11or
DI-568
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
796 Author
: Date
:
1997 SUPRA (RM502U)
5 Check D squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (-) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect the steering wheel pad connector.
(d) Connect negative (-) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON and wait at least 20
seconds.
(b) Clear malfunction code stored in memory.
(See page DI-557)
(c) Turn the ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(e) Using SST, connect the terminals Tc and E
1 of DLC1.
SST 09843-18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK

H03222
P squib
Spiral
Cable
ACC
ON
E
1Tc DLC1 Code 11orAirbag Sensor
Assembly
D squib
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-569
797 Author
: Date
:
1997 SUPRA (RM502U)
6 Check P squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (-) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect the front passenger airbag assembly connector.
(d) Connect negative (-) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(b) Clear malfunction code stored in memory.
(See page DI-557)
(c) Turn the ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(e) Using SST, connect the terminals Tc and E
1 of DLC1.
SST 09843-18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.

R05899R14301H07912
P squib
Spiral
CableAirbag Sensor
Assembly
D squib
D+
DI-570
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
798 Author
: Date
:
1997 SUPRA (RM502U)
7 Check spiral cable.
PREPARATION:
Disconnect the connector between airbag sensor assembly
and spiral cable.
CHECK:
Measure the resistance between D+ on spiral cable side of con-
nector between spiral cable and steering wheel pad and body
ground.
OK:
Resistance: 1 MW or higher
NG Repair or replace spiral cable.
OK
Repair or replace harness or connector be-
tween airbag sensor assembly and spiral
cable.

AB0119R05901R14288H07913
P squib
Spiral
CableAirbag Sensor
Assembly
D squib
ON
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-571
799 Author
: Date
:
1997 SUPRA (RM502U)
DTC 12 Short in Squib Circuit (to B+)
CIRCUIT DESCRIPTION
The squib circuit consists of the airbag sensor assembly, spiral cable, steering wheel pad and front passen-
ger airbag assembly. It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see FUNCTION OF COMPONENTS on page RS-2.
DTC 12 is recorded when a B+ short is detected in the squib circuit.
DTC No.DTC Detecting ConditionTrouble Area
12

Short circuit in squib wire harness (to B+).

Squib malfunction.

Spiral cable malfunction.

Airbag sensor assembly malfunction.
Steering wheel pad (D squib)

Front passenger airbag assembly (P squib)

Spiral cable

Airbag sensor assembly

Wire harness
WIRING DIAGRAM
Refer to page DI-564 for the WIRING DIAGRAM.
INSPECTION PROCEDURES
1 Preparation (See step 1 on page DI-595).
2 Check D squib circuit.
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and steering wheel pad, measure the voltage between D
+
and body ground.
OK:
Voltage: 0 V
NG Go to step 7.
OK
DI4WL-01

AB0119R05898R14288H07914
P squib
Spiral
CableAirbag Sensor
Assembly
D squib
ON
P
+
(+)
(-)
DI-572
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
800 Author
: Date
:
1997 SUPRA (RM502U)
3 Check P squib circuit.
CHECK:
For the connector (on the airbag sensor assembly side) be-
tween airbag sensor assembly and front passenger airbag as-
sembly, measure the voltage between P
+ and body ground.
OK:
Voltage: 0 V
NG Repair or replace harness or connector be-
tween the airbag sensor assembly and front
passenger airbag assembly.
OK

AB0069R05902AB0069AB0118AB0119FI1389N19819H07915
P squibAirbag Sensor
Assembly
D squib
Spiral
Cable
ACC
ON
or
E
1
Tc DLC1
Code 12
P+P-
D+D-
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-573
801 Author
: Date
:
1997 SUPRA (RM502U)
4 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to airbag sensor assembly.
(b) Using a service wire, connect D
+ and D- on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Using a service wire, connect P
+ and P- on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(d) Connect negative (-) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON and wait at least 20
seconds.
(b) Clear malfunction code stored in memory.
(See page DI-557)
(c) Turn the ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(e) Using SST, connect the terminals Tc and E
1 of DLC1.
SST 09843-18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
+
NG Replace airbag sensor assembly.
OK

H03224
P squib
Spiral
CableAirbag Sensor
Assembly
D squib
ON ACC
DLC 1Code 12
Tc E
1
or
DI-574
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
802 Author
: Date
:
1997 SUPRA (RM502U)
5 Check D squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (-) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect the steering wheel pad connector.
(d) Connect negative (-) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(b) Clear malfunction code stored in memory.
(See page DI-557)
(c) Turn the ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(e) Using SST, connect the terminals Tc and E
1 of DLC1.
SST 09843-18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK

H03225
P squib
Spiral
CableAirbag Sensor
Assembly
D squib
ON ACC
DLC 1Code 12
Tc E
1
or
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-575
803 Author
: Date
:
1997 SUPRA (RM502U)
6 Check P squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (-) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect the front passenger airbag assembly connector.
(d) Connect negative (-) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON and wait at least 20
seconds.
(b) Clear malfunction code stored in memory.
(See page DI-557)
(c) Turn the ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn the ignition switch to ACC or ON, and wait at least
20 seconds.
(e) Using SST, connect the the terminals Tc and E
1 of DLC1.
SST 09843-18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.