1997 TOYOTA SUPRA airbag

FOR THE TOYOTA DEALER
COLLISION REPAIR INFORMATION
TITLE: SRS AIRBAG COMPONENT REPLACEMENT PAGE 1 of 6
SECTION: ELECTRICAL BULLETIN #79
MODELS: ALL
DATE: AUGUST 1997
After an airbag has been deployed during a collision, it will be necessary to replace certain
components of the airbag system. Technicians can identify these parts by using the
attached matrix.
If the airbag does not deploy, yet the combination meter (airbag warning light) stays on for
more that 10 seconds after the key is turned to the ªACCº or ªONº position, it is necessary
to perform a diagnostic test. Always refer to the Toyota repair manual for the correct repair
procedure.
The attached information includes:

A matrix indicating components requiring replacement (pages 2±4).

Parts replacement note (page 5).

An example repair manual page outlining the diagnostic procedure available in
each model specific repair manual (page 6).
Toyota recommends the use of electrical repair kit (P/N 00002±04200±01) for any wiring
repairs. This kit includes a selection of numerous repair connectors, terminal ends, a repair
procedures manual and special tools specific to Toyota. The
replacement electrical wire
and connector (from the wire harness to the front sensors) is P/N 82988±24010.
Toyota also offers a video package which shows the operation of the SRS airbag system
(P/N 00401±42994).
CAUTION: SRS Airbag service work can be performed only AFTER 90 SECONDS
from the time the ignition switch is turned to the ªlockº position and the
negative (±) terminal cable is disconnected from the battery.
NOTE: PLEASE ROUTE THIS BULLETIN TO YOUR COLLISION REPAIR CENTER
MANAGER!

SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 2 of 6

SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 3 of 6

SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 4 of 6

SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 5 of 6
Component Replacement Notes
Note 1 ± Replace the following items:

Instrument panel

Center console bracket support
Note 2 ± Replace the following items if deformed:

Instrument panel

Instrument panel reinforcement

Glove compartment

Glove compartment door
Note 3 ± Replace the following items:

Instrument panel reinforcement

Glove compartment

Glove compartment door
Note 3a ± Replace the following items:

Instrument panel

Instrument panel reinforcement

Glove compartment door
Note 4 ± If the SRS wire harness assembly is damaged:

Use a repair wire specially designed for use in the SRS airbag system at the front
sensor (P/N 82988±24010).
OR

Replace the entire wire harness assembly.
Note 4a ± Replace wire harness if damaged.

Repair only if wire harness connector is damaged.
Note 4b ± Replace wire harness if damaged.
Note 5 ± Replace the following items if deformed:

Steering wheel

Spiral cable
Note 6 ± Replace center airbag sensor assembly if:

Center airbag sensor assembly has been found faulty in troubleshooting

Center airbag sensor assembly has been found faulty during the following checks:
1. Deformation of the bracket or case
2. Vinyl seal broken
3. Damage to connector

Center airbag sensor assembly has been dropped.

SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 6 of 6
This is an example from a Toyota Repair Manual. Always refer to the repair manual
applicable to the model and year vehicle you are diagnosing.

FOR THE TOYOTA DEALER
COLLISION REPAIR INFORMATION
TITLE: SRS AIRBAG COMPONENT REPLACEMENT PAGE 1 of 4
SECTION: ELECTRICAL BULLETIN #83
MODELS: ALL
DATE: MAY 1998
After an airbag has been deployed during a collision, it will be necessary to replace certain
components of the SRS system. Technicians can identify these parts by using the attached
matrix.
If, after the vehicle has been completely repaired, the airbag warning light stays on for
more than 6 seconds while the key is turned to the ªACCº or ªONº position, it is necessary
to perform a diagnostic test. Always refer to the model±specific Toyota Repair Manual for
the correct repair procedure.
The attached information includes:

A matrix indicating components requiring replacement (page 3).

Parts replacement notes (page 4).

An example Repair Manual page outlining the diagnostic procedure available in
each model±specific Repair Manual (page 2).
On some vehicles the front sensors may be replaced. Please refer to the model±specific
repair manual concerning front airbag sensor replacement requirements before performing
this repair. Three part numbers are available for
replacement electrical wire and
connectors from the wire harness to the front SRS sensors. They are P/N 82988±24010,
82988±50010, and 82988±33010.
Toyota also offers a video package which outlines the operation of the SRS airbag system
(P/N 00401±42994).
NOTE: PLEASE ROUTE THIS BULLETIN TO YOUR COLLISION REPAIR CENTER
MANAGER!

SRS COMPONENT REPLACEMENT (cont'd) PAGE 2 of 4
CAUTION: SRS Airbag service work can be performed only AFTER 90 SECONDS
from the time the ignition switch is turned to the ªlockº position and the
negative (±) terminal cable is disconnected from the battery.
This is an example from a Toyota Repair Manual. Always refer to the repair manual
applicable to the model and year of the vehicle you are diagnosing.