Page 694 of 1807
S05426
From
BatteryR/B
No.2 2
2A
ALT
R/B
No.2
POWER
22W-L
J/B No.1 210
1B 1ESTOP
WStop Light
Switch
21G-W11
IJ1G-W4
A
STPECM
J/B
No.1 1
101H
1C
Light
Failure
Sensor
To Stop LightG-W
7
- DIAGNOSTICSENGINE (2JZ-GTE)
DI-279
507 Author: Date:
1997 SUPRA (RM502U)
DTC P1520 Stop Light Switch Signal Malfunction
Only for A/T
CIRCUIT DESCRIPTION
This signal is used to detect when the brakes have been applied. The STP signal voltage is the same as
the voltage supplied to the stop lights.
The STP signal is used mainly to control the fuel cut-off engine speed. (The fuel cut-off engine speed is
reduced slightly when the vehicle is braking.)
DTC No.DTC Detecting ConditionTrouble Area
P1520
The stop light switch does not turn off even once the vehicle is
driven.
(2 trip detection logic)Short in stop light switch signal circuit
Stop light switch
ECM
WIRING DIAGRAM
DI4TK-01
Page 695 of 1807
A00726
ON
ONBrake Pedal
DepressedBrake Pedal
Released
Check Harness A
ECM
A4
STP(+)
DI-280
- DIAGNOSTICSENGINE (2JZ-GTE)
508 Author: Date:
1997 SUPRA (RM502U)
INSPECTION PROCEDURE
1 Check operation of stop light.
PREPARATION:
Check if the stop lights go on and off normally when the brake
pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check STP signal.
When using TOYOTA hand-held tester:
PREPARATION:
(a) Connect the TOYOTA hand-held tester to the DLC3.
(b) Turn the ignition switch ON and TOYOTA hand-held tes-
ter main switch ON.
CHECK:
Read the STP signal on the TOYOTA hand-held tester.
OK:
Break pedal is depressed: STP ... ON
Break pedal is released: STP ... OFF
When not using TOYOTA hand-held tester:
PREPARATION:
(a) Connect Check Harness A (See page DI-164).
(b) Turn ignition switch ON.
CHECK:
Check voltage between terminal STP of ECM and body ground.
OK:
Brake pedalVoltage
Depressed7.5 - 14 V
ReleasedBelow 1.5 V
OK Check for intermittent problems
(See page DI-147).
NG
Page 732 of 1807
DI4V5-01
ABS Check Sheet
Inspector 's
Name:
Customer 's Name
Date Vehicle
Brought InRegistration Year Registration No.
Frame No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency Problem Occurs/ /
ContinuousIntermittent ( times a day)
Remains ONDoes not Light Up
Symptomskm
miles
ABS does not operate.
ABS Warning Light
AbnormalABS does not operate efficiently.
Check ItemTRAC Indicator
LightNormalDoes not Light Up
2nd TimeNormal Code
Malfunction Code (Code )
Normal CodeMalfunction Code (Code )
1st Time
DTC Check
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-441
669 Author: Date:
1997 SUPRA (RM502U)
CUSTOMER PROBLEM ANALYSIS CHECK
Page 733 of 1807
DI4V6-01
F02620
R06980
Short Pin
DLC1
S-17-1 Iei-23-1-A
F00041
DLC2
Tc E 1DLC1
Tc E1
R01346
Normal Code
2 sec.
ON
OFF0.25
sec.
0.25
sec.
Code 11 and 21
0.5
sec.
4 sec.1.5
sec.2.5 sec.0.5
sec.
Code 21
Code 11 ON
OFF DI-442
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
670 Author: Date:
1997 SUPRA (RM502U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Check the Indicator,
When the ignition switch is turned ON, check that the ABS
warning light goes on for 3 seconds.
HINT:
If the indicator check result is not normal, proceed to trouble-
shooting for the ABS warning light circuit (See page DI-488).
(b) Check the DTC.
(1) Turn the ignition switch ON.
(2) Disconnect the short pin from DLC1.
(3) Using SST, connect terminals Tc and E1 of DLC2 or
DLC1.
SST 09843-18020
(4) Read the DTC from the ABS warning light on the
combination meter.
HINT:
If no code appears, inspect the diagnostic circuit or ABS warn-
ing light circuit (See page DI-494 or DI-488).
As an example, the blinking patterns for normal code and
codes 11 and 21 are shown on the left.
(5) Codes are explained in the code table on page
DI-447.
(6) After completing the check, disconnect terminals Tc
and E1, and turn off the display.
If 2 or more malfunctions are indicated at the same time, the
lowest numbered DTC will be displayed 1st.
Page 734 of 1807
FI6997
TOYOTA
Hand-held
tester
DLC2
BR3890
R06980
Short Pin
DLC1
N09348
TOYOTA hand-held tester
ECU
TOYOTA brake-out-box
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-443
671 Author: Date:
1997 SUPRA (RM502U)
(c) Using TOYOTA hand-held tester, check the DTC.
(1) Hook up the TOYOTA hand- held tester to the
DLC2.
(2) Read the DTC by following the prompts on the tes-
ter screen.
Please refer to the TOYOTA hand-held tester oper-
ator 's manual for further details.
(d) Clear the DTC.
(1) Using SST, connect terminals Tc and E1 of DLC2 or
DLC1 and remove the short pin from DLC1.
SST 09843-18020
(2) IG switch ON.
(3) Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 5 seconds.
(4) Check that the warning light shows the normal
code.
(5) Remove the SST from the terminals of DLC2 or
DLC1.
SST 09843-18020
(6) Connect the short pin to DLC1.
HINT:
Disconnecting the battery cable during repairs will not erase the
DTC in the ECU.
(e) Using TOYOTA brake-out-box and TOYOTA hand-held
tester, measure the ECU terminal values.
(1) Turn the IG switch OFF.
(2) Hook up the TOYOTA hand-held tester and TOYO-
TA break-out-box to the vehicle.
(3) Turn the IG switch ON.
(4) Read the ECU input/output values by following the
prompts on the tester screen.
HINT:
TOYOTA hand-held tester has a ºSnapshotº function.
This records the measured values and is effective in the diagno-
sis of intermittent problems.
Please refer to the TOYOTA hand-held tester/TOYOTA break-
out-box operator's manual for further details.
Page 735 of 1807
F00007
E1
Tc
Ts
lei-23-1-A
DLC1
BR3904
0.13 sec.
0.13 sec.
ON
OFF
BR3893
Malfunction Code (Example Code 72, 76)
7276
ON
OFF
0.5 sec.
0.5 sec.1.5 sec.
0.5 sec.0.5 sec.2.5 sec.
4 sec.
Repeat DI-444
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
672 Author: Date:
1997 SUPRA (RM502U)
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR
(a) Check the speed sensor signal and deceleration sensor.
(1) Turn the ignition switch OFF
(2) Using SST, connect terminal Ts and E1 of DLC1.
SST 09843-18020
(3) Start the engine.
(4) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS
warning light circuit (See page DI-488).
If the ABS warning light is always on, inspect and repair,
deceleration sensor.
(5) Drive the vehicle faster than 45 km/h (28 mph) for
several seconds.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc an E1 of DLC1.
SST 09843-18020
(8) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC shown on the next page.
If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunctions are indicated at the same time,
the lowest numbered code will be displayed 1st.
(9) After doing the check, disconnect terminals Ts and
E1, Tc and E1 of DLC1, and turn ignition switch OFF.
Page 738 of 1807
DI4V7-01
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-447
675 Author: Date:
1997 SUPRA (RM502U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that code. For details
of each code, turn to the page referred to under the ºSee pageº for the respective ºDTC No.º in the DTC chart.
HINT:
Using SST 09843-18020, connect the terminals Tc and E1, and remove the short pin.
If any abnormality is not found when inspect each inspection parts, inspect the ECU.
DTC No.
(See Page)Detection ItemTrouble Area
11
(DI-453)Open circuit in ABS solenoid relay circuitABS solenoid relay
Open or short in ABS solenoid relay circuit
12
(DI-453)Short circuit in ABS solenoid relay circuitABS solenoid relay
B+ short in ABS solenoid relay circuit
13*2
(DI-460)Open circuit in ABS motor relay circuitABS motor relay
Open or short in ABS motor relay circuit
14
(DI-460)Short circuit in ABS motor relay circuitABS motor relay
B+ short in ABS motor relay circuit
21
(DI-466)Open or short circuit in 2-position solenoid circuit for right front
wheelABS actuator
Open or short in SFRH or SFRR circuit
22
(DI-466)Open or short circuit in 2-position solenoid circuit for left front
wheelABS actuator
Open or short in SFLH or SFLR circuit
23
(DI-466)Open or short circuit in 2-position solenoid circuit for right rear
wheelABS actuator
Open or short in SRH (SRRH) or SRR (SRRR) circuit
24*1
(DI-466)
Open or short circuit in 2-position solenoid circuit for left rear
wheelABS actuator
Open or short in SRLH or SRLR circuit
31*2
(DI-469)Right front wheel speed sensor signal malfunction
32*2
(DI-469)Left front wheel speed sensor signal malfunctionRight front, left front, right rear and left rear speed sensor
O htihd iit33*2
(DI-469)Right rear wheel speed sensor signal malfunction
Open or short in each speed sensor circuit
Speed sensor rotor
34*2
(DI-469)Left rear wheel speed sensor signal malfunction
41
(DI-475)Low battery positive voltage
Battery
IC regulator
Open or short in power source circuit
43*1
(DI-479)
Malfunction in deceleration sensor
(constant output)Deceleration sensor
Wire harness for deceleration sensor system
44*1
(DI-480)Open or short in deceleration sensor circuitDeceleration sensor
Open or short in deceleration sensor circuit
45*1
(DI-479)Malfunction in deceleration sensorDeceleration sensor
Wire harness for deceleration sensor system
49
(DI-482)Open circuit in stop light switch circuitOpen in stop light circuit
51*2
(DI-484)
Pump motor is locked
Open in pump motor groundABS pump motor
Always
ON
(DI-485)Malfunction in ECU
IG power source circuitBattery
IC regulator
Open or short in power source circuit
Page 740 of 1807
DI4V8-01
W02807
2JZ-GE:
2JZ-GTE:
2JZ-GTE:SPORT AVS (2JZ-GTE Engine):
ABS Control
Relay
ABS Solenoid
Relay
ABS Motor RelayABS ActuatorDeceleration Sensor
ABS Warning Light
ABS ECU
DLC1DLC2
Front Speed Sensor RotorRear Speed SensorRear Speed
Sensor Rotor
Front Speed Sensor
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-449
677 Author: Date:
1997 SUPRA (RM502U)
PARTS LOCATION
