1997 SSANGYONG KORANDO power steering

OM600 ENGINE MECHANICAL 1B3 -- 65
D AEW OO M Y_2000
9. Disconnect the pipes of power steering pump and
remove the belt pulley.
Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then re-
move the power steering pump.
11. Remove the generator bracket (16).
12. Remove the fuel filter.

OM600 ENGINE MECHANICAL 1B3 -- 69
D AEW OO M Y_2000
10. Install the fuel filter.
Tightening Torque25 N∙m (18 lb-ft)
11. Install the vacuum pump.
Tightening Torque10 N∙m(89lb-in)
12. Install the power steering pump.
Tightening Torque23 N∙m (17 lb-ft)
13. Install the power steering pump pulley
Tightening Torque32 N∙m (24 lb-ft)
14. Install the guide pulley bracket
Tightening Torque9N∙m(80lb-in)

SSANGYONG MY2002
2A-2 SUSPENSION DIAGNOSIS
Inspect the tires for improper pressure and uneven wear.
Inspect the joint from the steering column to the steer-
ing gear for loose connections or wear.
Inspect the front and the rear suspension, the steering
gear, and the linkage for loose or damaged parts.
Inspect for out-of-round tires.
Inspect for out-of-balance tires, bent wheels, and worn
or loose wheel bearings.
Check the power steering pump serpentine belt tension.
Inspect the power steering system for leaks. Also, check
the power steering fluid level.Action
Checks
Checks
Inspect for incorrect toe on the front and the rear wheels.
Inspect for a twisted or a bent suspension arm. Inspect for mismatched or uneven tires.
Inspect for a broken or a sagging spring.
Inspect for a radial tire lateral force.
Check the front-wheel alignment.
Inspect for an off-center steering gear.
Inspect for front-brake dragging.
DIAGNOSIS
GENERAL DIAGNOSIS
Problems in the steering, the suspension, the tires,
and the wheels involve several systems. Consider all
systems when diagnosing a complaint. Some problems,
such as abnormal or excessive tire wear and scuffed
tires, may be the result of hard driving. Always roadtest the vehicle first. If possible, do this road test with
the customer.
Proceed with the following preliminary checks. Correct
any substandard conditions.
Preliminary Checks
Replace the tires.
Replace the spring.
Check the wheel alignment. Switch the tire and the
wheel assemblies. Replace the tires, as needed.
Align the front wheels.
Reseat the pinion valve assembly. Replace the pinion
valve assembly, as needed.
Adjust the front brakes.
Car Lead/Pull
Action
Adjust the toe on the front and the rear wheels.
Replace the suspension arm.
Scuffed Tires
Inflate the tires to the proper pressure.
Tighten the intermediate shaft pinch bolts. Replace the
intermediate shaft, as needed.
Tighten the front and the rear suspension. Tighten the
steering gear mounting bracket bolts. Tighten the inter-
mediate shaft pinch bolts. Replace the front and the rear
suspension, as needed. Replace the steering gear, as
needed. Replace the intermediate shaft, as needed.
Perform a free runout test. Match-mount the tires.
Balance the wheels. Replace the wheels. Replace the
wheel bearings.
Tighten the power steering pump serpentine belt.
Repair any leaks. Perform a power steering system test.
Add power steering fluid, as needed.
Action Checks

SUSPENSION DIAGNOSIS 2A-3
SSANGYONG MY2002
Perform a rack bearing preload adjustment.
Replace the seals and the hoses, as needed.
Lubricate the steering gear. Repair or replace the
steering gear, as needed.
Tighten the steering gear mounting bracket nuts and
the bolts. Check the steering gear preload adjustment.
Check the hydraulic system. Test the power steering
system pressure with a gauge.
Inspect for binding or catching in the steering gear.
Inspect for a loose steering gear mounting.Action ChecksBalance the tire or the wheel.
Measure the hub flange runout. Replace the hub, as
needed.
Adjust the brakes. Replace the brake rotor, as needed.
Replace the outer tie rods.
Balance the wheel.
Replace the lower ball joint.
Measure the wheel runout. Replace the wheel, as
needed.
Match-mount the tire and the wheel assembly. Inspect for an out-of-balance tire or wheel.
Inspect for excessive wheel hub runout.
Inspect for excessive brake rotor imbalance.
Inspect for worn tie rod ends.
Inspect for wheel trim imbalance.
Inspect for a worn lower ball joint.
Inspect for excessive wheel runout.
Inspect for excessive loaded radial runout on the tire
and the wheel assembly.Action ChecksAction
Balance the tire or the wheel. Checks
Inspect for an out-of-balance tire or wheel.Align the front and the rear wheels.
Adjust the toe on the front and the rear wheels.
Replace the spring.
Balance the tires.
Rotate the tires. Replace the tires, as needed.
Maintain the proper load weight.
Inflate the tires to the proper pressure. Check the front-wheel and the rear-wheel alignment.
Inspect for excessive toe on the front and the rear wheels.
Inspect for a broken or a sagging spring.
Inspect for out-of-balance tires.
Check for a failure to rotate tires.
Check for an overloaded vehicle.
Inspect for low tire inflation.
Abnormal or Excessive Tire Wear
Shimmy, Shake, or Vibration
Hard Steering
Wheel Tramp
Action Checks

SSANGYONG MY2002
2A-6 SUSPENSION DIAGNOSIS
Check the front-wheel and the rear-wheel alignment.
Inspect for worn dampeners.
Inspect for worn or loose wheel bearings.
Inspect for excessive tire or wheel runout.
Inspect for a worn ball joint.
Check the steering gear preload adjustment.Align the front and the rear wheels.
Replace the dampeners.
Replace the wheel bearings.
Match-mount the tires. Replace the tires, as needed.
Replace the wheels, as needed.
Replace the ball joint.
Perform a rack bearing preload adjustment.Action ChecksReplace the seals and the hoses, as needed.
Clean the pinion valve assembly. Replace the pinion
valve assembly, as needed.
Adjust the power steering pump serpentine belt. Check the hydraulic system. Test the power steering
system pressure with a gauge.
Inspect for a sluggish steering gear valve.
Inspect for a loose power steering pump serpentine
belt.Action ChecksAction Checks
Purge the power steering system of air.
Tighten the steering gear mounting bracket nuts and
the bolts.
Tighten the intermediate shaft pinch bolts. Replace the
intermediate shaft, as needed.
Tighten the tie rod ends. Replace the outer tie rods, as
needed.
Replace the front wheel bearings. Inspect for air in the power steering system.
Inspect for a loose steering gear mounting.
Inspect the joint from the column to the steering gear
for loose connections or wear.
Inspect for loose tie rod ends.
Inspect for loose or worn front wheel bearings.
Steering Wheel Surges or Jerks
Cupped Tires
Steering Wheel Kickback

WHEEL ALIGNMENT 2B-7
SSANGYONG MY2002
VEHICLE HEIGHT
Adjustment Procedure
1. Check the tire for proper inflation.
2. Measure ‘A’ from the center of the lower arm
rear mounting bolt end to the ground.
KAA2B050
3. Measure ‘B’ from the center of the steering
knuckle shaft to the ground.
KAA2B060
4. If the difference between ‘A’ and ‘B’ is not
within specification, adjust vehicle height using
torsion bar height control bolt.
Adjustment Notice
Specification31 - 36 mm
(1.22 - 1.42 inch)B - A
Notice: Before wheel alignment, adjust vehicle
height adjustment first.
KAA2B070
FRONT TOE-IN ADJUSTMENT
Adjustment Procedure
1. Disconnect the outer tie rods from the knuckle as-
semblies. Refer to Section 6C, Power Steering
Gear.
2. Loosen the front toe adjusting nut.
Notice: In this adjustment, the right and the left tie
rods must be equal in length, or the tires will wear
unevenly.
3. Turn the right and the left outer tie rods to align the
toe to the proper specifications. Refer to “Wheel
Alignment Specifications” in this section.
KAA2B080
4. Hold the outer tie rod and tighten the front toe adjust-
ing nut.
Adjustment Notice
Tightening Torque 73 Nm (54 lb-ft)
5. Reconnect the outer tie rods to the knuckle assem-
blies. Refer to Section 6C, Power Steering Gear.

FRONT AXLE 3A-13
SSANGYONG MY2002
Tools Required
DW340-80Front Axle Support
Removal and Installation Procedure
1. Raise and suitably support the vehicle.
2. Remove the lower cover.
Installation Notice
KAA3A240
KAA3A260
KAA3A250
5. Remove the front drive shaft-to-front axle
assemblybolts.
Installation Notice
Tightening Torque4.5 - 6.0 kgfm 3. Remove the rack and pinion assembly. Refer to
Section 6C, Power Steering Gear.
4. Remove the front axle bleeder hose.
Tightening Torque 35 Nm (26 lb-ft)
KAA3A270
6. Remove the front propeller shaft-to-front axle bolts.
Removal Notice
Make alignment marks on the front propeller
shaft and front axle housing.
Installation Notice
Tightening Torque7.0 - 8.5 kgfm

SECTION 6A
POWER STEERING SYSTEM
TABLE OF CONTENTS
Description and Operation...................................6A-2
General Description.............................................6A-2
Component Locator.............................................6A-3
Diagnostic Information and Procedures..............6A-4
Power Steering System Pressure Test..................6A-4
Power Steering System Leak Test........................6A-4
Maintenance .........................................................6A-5
Bleeding the Power Steering System....................6A-5
Checking and Adding Fluid..................................6A-5Repair Instructions................................................6A-6
On-Vehicle Service.................................................6A-6
Power Steering Fluid Reservoir.............................6A-6
Power Steering Pump Hoses and Pipes................6A-7
Specifications.......................................................6A-9
General Specification...........................................6A-9
Fastener Tightening Specifications.......................6A-9
Special Tools and Equipment............................ 6A-10
Special Tools Table............................................6A-10