1997 SSANGYONG KORANDO wiring

AUTOMATIC TRANSMISSION 5A-195
SSANGYONG MY2002
19. Holding the separator plate to the upper valve
body to prevent the check balls from falling out,
install the upper valve body on the lower valve
body. Install all screws finger tight then tighten
the screws to specification in the prescribed
sequence.
Installation Notice
The wiring loom ground wire eyelet terminal is
secured beneath the solenoid 1 retainer. 16. Install the reverse lockout valve, spring, plug and
retaining plate. Ensure that the valve is correctly
oriented.
17. Position the five nylon ball checks in the upper
valve body.
18. Fit the upper valve body gasket. Install the
separator plate over the upper valve body.
KAA5A830 KAA5A840 KAA5A1V0
Tightening Torque11 - 16 Nm
(8 - 12 lb-ft)
20. Install solenoids 1, 2, 3, 4 and 6. Ensure the
solenoid is firmly secured by the retainer and that
the screw is tightened to specification.
Installation Notice
8 - 12 Nm
(71 - 106 lb-in)

AUTOMATIC TRANSMISSION 5A-197
SSANGYONG MY2002
2. Carefully assemble the oil filter to the valve body.
The spigot must not lean on one side while being
fitted.
3. Secure the oil filter assembly with the retainer.
4. Check that the magnet is located in the dimple in
the corner of the oil pan.
5. Assemble the gasket on the pan lip. The gasket
must be free of any distortion when installed. 25. Check the alignment of the detent roller and the
manual lever quadrant.
26. Connect the solenoid wiring as detailed below:
Solenoid 1 - red
Solenoid 2 - bIue
Solenoid 3 - yellow
Solenoid 4 - orange
Solenoid 5 - green
Solenoid 6 - violet
Notice: All hardware must be correctly installed and
torqued to specification.
Oil Filter and Pan Assembly
Notice:
Replace the filter whenever rebuilding a
transmission where a significant amount of
mechanical damage has occurred.
To aid the assembly of the pan gasket, use a small
amount of Vaseline at the pan/gasket interface. This
ensures that the gasket remains on the pan ridge.
Do not over torque pan bolts as this may distort
the pan and cause leaks.
Ensure that the internal line pressure plus in the
valve body is fitted.
1. Lubricate the oil filter sealing ring with automatic
transmission fluid.
KAA5A2B0 KAA5A2A0
KAA5A510

5A-202 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
KICKDOWN SWITCH
1. Separate the Kickdown Switch from the Kickdown
Switch bracket by pushing the lock.
2. Disconnect the Kickdown Switch connector.
3. Installation should follow the removal procedure in
the reverse order.
KAA5A5S0
GEAR SHIFT CONTROL LEVER
Disassembly and Assembly Procedure
1. Disconnect the negative battery cable.
2. Remove the gear shift control lever assembly.
Refer to Section 9G, interior Trim.
3. Remove the gear shift control lever knob.
4. Separate the upper and middle housing from the
gear shift control lever assembly by unlocking the
lock.
5. Remove the upper housing.
6. Disconnect the P position lamp by turning it from
the middle housing.
7. Remove the P position switches assembly bolts.
8. Remove the middle housing with the mode
selector switch wiring harness from the gear shift
control lever assembly.
9. Separate the P position switches assembly with
the P position lamp wiring harness from the gear
shift control lever assembly.
Notice: Adjust the brake transmission shift interlock
ease the operation well.
10. Remove the clips supporting the springs and
bushes from the pin of the pin of the gear shift
control lever.
11. Remover the spring and bushes from the pin of
the gear shift control lever.
12. Remove the gear shift control lever by pushing
the pin.
13. Installation should follow the removal procedure
in the reverse order.
KAA5A5P0
KAA5A5Q0
KAA5A5R0

5A-206 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
TCM WIRING DIAGRAM (GASOLINE ENGINE - 1
SCHEMATIC AND ROUTING DIAGRAMS
KAA5A010

AUTOMATIC TRANSMISSION 5A-207
SSANGYONG MY2002
TCM WIRING DIAGRAM (GASOLINE ENGINE - 2 OF 2)
KAA5A020

5A-208 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
TCM WIRING DIAGRAM (DIESEL ENGINE - 1 OF 2)
YAD5A230

AUTOMATIC TRANSMISSION 5A-209
SSANGYONG MY2002
TCM WIRING DIAGRAM (DIESEL ENGINE - 2 OF 2)
YAD5A240

MANUAL TRANSMISSION 5B-19
SSANGYONG MY2002
TRANSMISSION
Removal Procedure
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the drain plug from the transmission
housing and drain the oil. Reinstall the drain plug.
4. Disconnect the back-up switch connector.
5. Remove the breather hose.
YAD5B280
YAD5B290
YAD5B300
YAD5B310
6. Remove the speedometer connector and other
wiring harnesses and connectors.