Page 1412 of 2053
SSANGYONG MY2002
5D2-12 TRANSFER CASE (PART TIME - 4408)
KAA5D120
KAA5D130
Defective Code Reading
1. Position the ignition switch to OFF.
2. Using a service connector, connect the diagnosis
socket under instrument pannel.
3. Position the ignition switch to ON.
4. Read the flashing 4WD CHECK indicator light and
identify the malfunctioning part (See Diagnosis
Table).
How to Clear the Fault Code
1. Position the ignition switch to OFF.
2. Using a service connector, connect the diagnosis
socket in under instrument pannel.
3. Position the ignition switch to ON over 5 seconds.
4. Do defective code reading and make sure that all
defective codes are eliminated.
Page 1413 of 2053
TRANSFER CASE (PART TIME - 4408) 5D2-13
SSANGYONG MY2002
Diagnostic Table
Connect a service connector. If turn the ignition switch
“ON” “4WD CHECK” indicator light will come on for
0.6 second and turn off for 3 seconds and then display
a defective code 3 times continuously.
4WD CHECK
Light
ON
OFF
4WD CHECK
Light
ON
OFF
4WD CHECK
Light
ON
OFF
4WD CHECK
Light
ON
OFF
4WD CHECK
Light
ON
OFFTCCU
Shift Motor
Synchronizer Clutch
Speed Sensor
Locking Hub Solenoid Defective Code No.
1
2
3
4
5
Malfunctioning Part
KAA5D140
KAA5D150
KAA5D160
KAA5D170
KAA5D180
Page 1420 of 2053

TRANSFER CASE (PART TIME - 4408) 5D2-21
SSANGYONG MY2002
KAA5D240
4H AND 4L INDICATOR
When the ignition switch turns on, 4H and 4L indicators
turn on for 0.6 seconds and turn off.
Notice: If 4H and 4L indicators do not turn on, check
the related bulb, the wiring harness and TCCU.
J1 - 7
J1 - 8
J1 - 13
J1 - 14
J1 - 15
J1 - 16
J1 - 17
J1 - 234H or 4L
2H
4H indicator light ON
4H indicator light OFF
2H or 4H
4L
Clutch pedal applied
Clutch pedal released
4L indicator light ON
4L indicator light OFF
Motor OFF
Motor ON
Motor OFF
Motor ON
Auto locking hub ON
Auto locking hub OFF
TCCU INSPECTION
4.75 - 5.35
0 - 0.50
< 1.00
> 11.00
4.75 - 5.35
0 - 0.50
< 0.50
> 11.00
< 1.00
> 11.00
< 1.00
> 11.00
< 1.00
> 11.00
> 11.00
< 1.00
Pin No. Voltage(V)Operation Condition
Notice:
DC 12V for the TCCU operation should be
maintained.
In case of J1-8 and J1-15, indicator light will turn
on for 0.6 second when turn the ignition switch ON.
If 4H and 4L indicator lights remain turned on when
turn the ignition switch on or during driving, perform
the TCCU diagnosis.
Page 1487 of 2053

SECTION 6E
POWER STEERING AND COLUMN
TABLE OF CONTENTS
Description and Operation...................................6E-2
General Description.............................................6E-2
Ignition Switch Keyhole Lamp..............................6E-2
Ignition Key Reminder .........................................6E-2
Component Locator.............................................6E-3
Diagnostic Information and Procedures..............6E-4
Steering Wheel Freeplay Inspection.....................6E-4
Steering Effort Inspection.....................................6E-4
Steering Column Diagnosis..................................6E-5
Repair Instructions................................................6E-9On-Vehicle Service.................................................6E-9
Headlamp/Turn Signal Switch and Lever...............6E-9
Wiper Switch and Lever.....................................6E-10
Steering Wheel With Sir.....................................6E-10
Ignition Lock Cylinder and Switch......................6E-11
Steering Column................................................6E-12
Specifications.....................................................6E-14
Fastener Tightening Specifications.....................6E-14
Special Tools and Equipment............................6E-15
Special Tools Table............................................6E-15
Page 1488 of 2053

SSANGYONG MY2002
6E-2 POWER STEERING AND COLUMN
GENERAL DESCRIPTION
Caution: To ensure the energy-absorbing action of
the steering column, it is important to use only the
specified screws, bolts, and nuts, tightened to the
specified torque.
In addition to the steering function, the steering column
provides safety and security.
The energy-absorbing column is designed to compress
in a front-end collision to lessen the chance of driver
injury.
The ignition switch and the lock are mounted on the
column, allowing the ignition and steering operations
to be locked to inhibit theft of the car.
The column levers trigger the turn signals, the headlight
beams, and the windshield washer and wipers.
A tilt steering column uses a spherical joint to allow
the steering wheel to tilt up and down. This enables
the driver to adjust the steering wheel to a comfortable
position.
Notice: Apply a thin coat of lithium grease to all friction
points when reassembling.
The column may be disassembled and reassembled
easily.
DESCRIPTION AND OPERATION
IGNITION SWITCH KEYHOLE LAMP
For description and lamp replacement information, Re-
fer to Section 9B, Lighting Systems.
IGNITION KEY REMINDER
The ignition key reminder alerts the driver that the key
is still in the ignition when the driver attempts to exit
the vehicle.
An internal switch in the ignition lock cylinder supplies
battery voltage to the reminder chime module when all
of the following conditions are true:
•The key is in the ignition switch.
The ignition is OFF.
The driver’s door is open.
For information on removal and installation of the re-
minder chime module, Refer to Section 9E, Instrumen-
tation/Driver Information.
Page 1491 of 2053

POWER STEERING AND COLUMN 6E-5
SSANGYONG MY2002
Check the lock cylinder for damage.
Check the ignition switch for lack of free movement.
Check the steering column housing for binding or
damage.ChecksActionReplace the lock cylinder.
Lubricate the ignition switch.
Remove the steering shaft and clear the steering
column housing. Replace the steering column housing
as needed.
Lock System Will Not Lock
High Lock Effort
Check the lock cylinder for damage.
Check the ignition switch for lack of free movement.
Check for extreme misalignment of the housing to the
cover.
Check for a bent ignition switch mounting bracket.ChecksActionReplace the lock cylinder.
Lubricate the ignition switch.
Realign the cover on the housing. Replace the cover
as needed.
Replace the ignition switch mounting bracket.
STEERING COLUMN DIAGNOSIS
Lock System
Lock System Will Not Unlock
Check the lock cylinder for damage.
Check the ignition switch for lack of free movement.
Check the steering column housing for binding or
damage.ChecksActionReplace the lock cylinder.
Lubricate the ignition switch.
Remove the steering shaft and clear the steering
column housing. Replace the steering column housing
as needed.
High Lock Effort
Check to see that the ignition switch is set correctly.
Check the lock cylinder for damage.ChecksActionReset the ignition switch.
Replace the lock cylinder. Reset the ignition switch.
Check the steering gear-to-column joints for improper
installation.
Check the steering shaft bearing for wear or damage.
Check the spherical joint for lack of lubrication.
Check the steering shaft for lack of lubrication.
Check the shaft lock snap ring for improper seating.ChecksActionTighten the steering shaft universal joint pinch bolts.
Replace the steering shaft joints as needed.
Replace the steering shaft bearing.
Lubricate the spherical joint.
Lubricate the steering shaft bearing.
Adjust the shaft lock snap ring.
Replace the shaft lock snap ring as needed.
Column
Noise in the Column
Page 1494 of 2053

SSANGYONG MY2002
6E-8 POWER STEERING AND COLUMN
Check the ignition switch for damage.
Check the ignition switch for improper installation.
Check the ignition switch electrical connector for
improper installation.ChecksActionReplace the ignition switch.
Remove and inspect the ignition switch. Reinstall the
ignition switch.
Reconnect the ignition switch electrical connector.
Replace the ignition switch electrical connector.
Ignition Switch Will Not Turn
Wiper/Cruise Control Switch Lever
Switch Inoperative: No LOW, HIGH, INTERMITTENT or WASH
Check the wiper switch for damage.
Check the wiper switch for improper installation.
Check the cruise control switch for damage.ChecksActionReplace the wiper/cruise control switch.
Remove and inspect the wiper/cruise control switch.
Reinstall the wiper/cruise control switch.
Replace the wiper/cruise control switch.
Ignition Switch
Electrical System Will Not Function
Check the ignition switch for damage.
Check the ignition switch for improper installation.ChecksActionReplace the ignition switch.
Remove and inspect the ignition switch. Reinstall the
ignition switch.
Page 1497 of 2053
POWER STEERING AND COLUMN 6E-11
SSANGYONG MY2002
KAA6E040
KAA6E100
KAA6E090
4. Remove the steering wheel using the steering
wheel puller 661 589 00 33 00.
Installation Notice:
Align the match marks on the steering wheel
and the steering column shaft.
IGNITION LOCK CYLINDER AND
SWITCH
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the upper and the lower steering column
cover screws.
3. Remove the upper and the lower steering column
cover.
4. Remove the screws for illumination keyhole
connection.
5. With the key in the ignition turned to the position
designated ACC, remove the lock cylinder by
pressing down the detent spring with a 2.5 mm
allen wrench or other suitable tool, and pulling the
lock cylinder out of the cylinder housing.