1996 TOYOTA TERCEL wiring

R15076
F6
B
EA2 B-R
MAIN
FL
Battery ALT13 Driver Side J/B
SRS
1J
F7 12
B-R1
1E
4 8 5
Tc LA B-Y R-G
*1
12 1F
1F
1F
1F 1KSRS Warning Light
45
B-Y
*2
AB DLC1
11 P-B
P-B P-BEA1Tc
(w/ Front Passenger Airbag)
*1: LA - 8
*2: Tc - 7
(w/o Front Passenger Airbag)
*1: LA - 6
*2: Tc - 5Airbag Sensor
Assembly
IG1
B-Y
B-Y4
7
5 DI-180
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TERCEL (RM440U)
SRS Warning Light System Malfunction (Always lit up when igni-
tion switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the ignition switch is
turned from the LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking of the SRS warn-
ing light.
WIRING DIAGRAM
DI4MJ-02

N14677
Fuse
DI-182
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TERCEL (RM440U)
SRS Warning Light System Malfunction (Does not light up when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to inform the driver of the abnormality
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI-180 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check SRS Fuse.
PREPARATION:
Remove SRS fuse.
CHECK:
Check continuity of SRS fuse.
OK:
Continuity
HINT:

Fuse may be burnt out even if it appears to be OK during
visual inspection.

If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI-177)
DI4MK-02

R15077
Airbag Sensor
Assembly
4
IK*1 2
Tc DLC1
E18
AA
BR
EA1Driver Side J/B
311P-B BR
ECJunction
ConnectorP-B P-B
IF
Tc
(w/ Front Passenger Airbag)
*1: Tc - 7
(w/o Front Passenger Airbag)
*1: Tc - 5
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-185
1996 TERCEL (RM440U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E1 of the DLC1 the airbag sensor assembly is set in the DTC output mode.
The DTCs are displayed by the blinking of the SRS warning light.
WIRING DIAGRAM
DI4ML-02

DI4MR-02
N20816
BatteryEngine Room
Relay BlockInstrument Panel
Junction BlockTheft Deterrent ECU
+B1
T41
1D8
1K11
L-Y L-Y
2
MAIN FL
EA2BDOME 1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-197
1996 TERCEL (RM440U)
CIRCUIT INSPECTION
ECU Power Source Circuit (w / Theft deterrent System)
CIRCUIT DESCRIPTION
This circuit provides power to operate the theft deterrent and door lock ECU.
WIRING DIAGRAM

N12865DOME Fuse

Engine Room Relay Block
I05884
(+)
(-)E +B1
OFF
DI-198
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check DOME fuse.
PREPARATION:
Remove DOME fuse from engine room relay block.
CHECK:
Check continuity of DOME fuse.
OK:
Continuity
NG Check for short in all the harness and compo-
nents connected to the DOME fuse
(See attached wiring diagram).
OK
2 Check voltage between terminals +B1 and E of ECU connector.
PREPARATION:
Disconnect the theft deterrent and door lock ECU connectors.
CHECK:
Measure voltage between terminals +B1 and E of ECU connec-
tor.
OK:
Voltage: 10 - 14 V
OK Proceed to next circuit inspection shown on
matrix chart (See page DI-196).
NG

N20817
BatteryInstrument Panel
Junction BlockTheft Deterrent ECU
(Door Lock Control Relay)
1J2
W-G
MAIN FLEA2
F7 F6 221A3
D6 (8)
T39
D6 (16)
T34
A A
IEJ3
JUNCTION
CONNECTOR A
AW-B
ALT AM1POWER
2 1L
W-B B W-G
( ): w/o Theft Deterrent System+B2
(B)
E
B-R B-R2JUNCTION
CONNECTOR J6
J/B No.2
11J/B No.7 DI-200
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
Actuator Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to drive the door lock motor.
WIRING DIAGRAM
DI4MS-01

N13109
 Relay Block No.7
POWER M-Fuse
1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-201
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check POWER M-fuse.
PREPARATION:
(a) Remove the finish low center panel.
(b) Remove the POWER M-fuse from R/B No.7.
CHECK:
Check continuity of POWER M-fuse.
OK:
Continuity
NG Check for short in all the harness and compo-
nents connected to the POWER M-fuse
(See attached wiring diagram). *1
OK

N12882
ID1
IH1
BJ1
BK1Theft Deterrent ECU
(Door Lock Control Relay)
( ): w/o Theft Deterrent System JUNCTION
CONNECTOR B R
GC
8 IE8 5 4
4 2T3 D63 (4)
T3 D62 (3) J6
JUNCTION
CONNECTOR
C
GG
G
G
GG
G
GC
CACT+
ACT-
B
BID2
IH1
BJ1
BK1 5 4
4 2 Door Lock Motor
Driver's
Rear Left Passenger's
Rear Right R
R
RR
R
R
R IE1
14
R 7
9
2
21
8
6
6
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-203
1996 TERCEL (RM440U)
Door Lock Motor Circuit
CIRCUIT DESCRIPTION
This door lock motor locks and unlocks the door in accordance with signals from the ECU.
WIRING DIAGRAM
DI4MT-02