1996 TOYOTA TERCEL wiring

- DIAGNOSTICSENGINE
DI-89
1996 TERCEL (RM440U)
DTC P1335 Crankshaft Position Sensor Circuit
Malfunction (During engine running)
CIRCUIT DESCRIPTION
Refer to DTC P0335 on page DI-60.
DTC No.DTC Detection ConditionTrouble Area
P1335No crankshaft position sensor signal to ECM with engine
speed 1,000 rpm or more
Open or short in crankshaft position sensor circuit

Crankshaft position sensor

ECM
WIRING DIAGRAM
Refer to DTC P0335 on page DI-60.
DI1EH-14

A15727
DI-90
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
DTC P1500 Starter Signal Circuit Malfunction
CIRCUIT DESCRIPTION
When the engine is cranked, the intake air flow is slow, so fuel vaporization is poor. A rich mixture is therefore
necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is ap-
plied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for
the starting injection control and after-start injection control.
DTC No.DTC Detection ConditionTrouble Area
P1500No starter signal to ECM

Open or short in starter signal circuit

Open or short in ignition switch or starter relay circuit

ECM
HINT:
In this circuit, diagnosis can only be made in the check mode.
WIRING DIAGRAM
DI95S-01

A15728
A15729
DI-92
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
DTC P1600 ECM BATT Malfunction
CIRCUIT DESCRIPTION
Battery positive voltage is supplied to terminal BATT of the ECM even when the ignition switch is OFF for
use by the DTC memory and air-fuel ratio adaptive control value memory, etc.
DTC No.DTC Detection ConditionTrouble Area
P1600Open in back up power source circuit
Open in back up power source circuit

ECM
HINT:
If DTC P1600 appear, the ECM does not store another DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminal BATT of ECM connector and body ground.
PREPARATION:
Remove the lower finish panel.
CHECK:
Measure the voltage between terminal BATT of the ECM con-
nector and the body ground.
OK:
Voltage: 9 - 14 V
OK Check and replace ECM (See page IN-26).
NG
DI01I-24

A15731
P24793
- DIAGNOSTICSENGINE
DI-95
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check park/neutral position switch.
PREPARATION:
Disconnect the park/neutral position switch connector.
CHECK:
Check continuity between each terminal shown below when the
shift lever is positioned to each range.
OK:
Shift PositionTerminal No. to continuity
P4 - 75 - 6
R4 - 8-
N4 - 105 - 6
D4 - 9-
22 - 4-
L3 - 4-

A15734
- DIAGNOSTICSENGINE
DI-97
1996 TERCEL (RM440U)
ECM Power Source Circuit
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied to the coil, closing the contacts of
the EFI main relay and supplying power to the terminal +B of the ECM.
WIRING DIAGRAM
DI4LL-02

A15738
- DIAGNOSTICSENGINE
DI-101
1996 TERCEL (RM440U)
WIRING DIAGRAM

A15740
DI-106
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
A/C Cut Control Circuit
CIRCUIT DESCRIPTION
This circuit cuts air conditioning operation during vehicle acceleration in order to increase acceleration per-
formance. During acceleration with the vehicle speed at 25 km/h (16 mph) or less, engine speed at 1,200
rpm or less and throttle valve opening angle at 50° or more, the A/C magnet switch is turned OFF for several
seconds.
WIRING DIAGRAM
INSPECTION PROCEDURE
TOYOTA hand-held tester:
1 Connect TOYOTA hand-held tester and check operation of air conditioning cut
control.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand-held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand-held tester main switch ON.
(d) Start the engine and air conditioning switch ON.
HINT:
A/C magnet clutch is turned ON.
(e) Select the ACTIVE TEST mode on the TOYOTA hand-held tester.
CHECK:
Check operation of A/C magnet clutch cut when air conditioning cut control is operated by the TOYOTA
hand-held tester.
OK:
A/C magnet clutch is turned OFF
OK Proceed to next circuit inspection shown on
matrix chart (See page DI-19).
DI1EK-09

DI98C-01
R03953
A13
1 2 3 4 5 6
7 8 9 10 11 1213
14 15
16 17 18 19 20 21 22 23 24 25 2612 11 12 3 4 5 6 7 8 9 10
A12
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-1 17
1996 TERCEL (RM440U)
TERMINALS OF ECU
Symbols (Terminal No.)Wiring ColorConditionSTD Voltage (V)
IG1 (A12-5) - GND (A13-7)B-Y - W-BIG switch ON10 - 14
SR (A12-20) - R+ (A12-4)G-B - L-BIG switch ON9 - 14
MR (A12-7) - R+ (A12-4)G-R - L-BIG switch ONBelow 1.0
SFRR (A13-5) - GND (A13-7)Y-R - W-BIG switch ON ABS warning light OFF10 - 14
SFRH (A13-6) - GND (A13-7)Y - W-BIG switch ON ABS warning light OFF10 - 14
SFLR (A12-2) - GND (A13-7)R-B - W-BIG switch ON ABS warning light OFF10 - 14
SFLH (A12-1) - GND (A13-7)P - W-BIG switch ON ABS warning light OFF10 - 14
SRRR (A12-15) -
GND (A13-7)L-W - W-BIG switch ON ABS warning light OFF10 - 14
SRRH (A12-14) -
GND (A13-7)R-W - W-BIG switch ON ABS warning light OFF10 - 14
SRLR (A13-11) - GND (A13-7)G-Y - W-BIG switch ON ABS warning light OFF10 - 14
SRLH (A13-12) -
GND (A13-7)Y-B - W-BIG switch ON ABS warning light OFF10 - 14
AST (A12-8) - GND (A13-7)LG - W-BIG switch ON ABS warning light OFF10 - 14
MT (A12-26) - GND (A13-7)LG-B e W-BIG switch ONBelow 1.5
WA (A12 18) GND (A13 7)RL WBIG switch ON ABS warning light ONBelow 2.0WA (A12-18) - GND (A13-7)R-L - W-BIG switch ON ABS warning light OFF10 - 14
STP (A12 12) GND (A13 7)GW WBStop light switch OFFBelow 1.5STP (A12-12) - GND (A13-7)G-W - W-BStop light switch ON8 - 14
Tc (A12-25) - GND (A13-7)P-B - W-BIG switch ON10 - 14
Ts (A12-24) - GND (A13-7)L - W-BIG switch ON10 - 14
FR+ (A12-10) - FR- (A12-9)B - WIG switch ON Slowly turn right front wheelAC generation
FL+ (A12-22) - FL- (A12-23)R - GIG switch ON Slowly turn left front wheelAC generation
RR+ (A13-8) - RR- (A13-9)L - LGIG switch ON Slowly turn right rear wheelAC generation
RL+ (A13-3) - RL- (A13-2)V - PIG switch ON Slowly turn left rear wheelAC generation