1996 TOYOTA TERCEL diagram

N20817
BatteryInstrument Panel
Junction BlockTheft Deterrent ECU
(Door Lock Control Relay)
1J2
W-G
MAIN FLEA2
F7 F6 221A3
D6 (8)
T39
D6 (16)
T34
A A
IEJ3
JUNCTION
CONNECTOR A
AW-B
ALT AM1POWER
2 1L
W-B B W-G
( ): w/o Theft Deterrent System+B2
(B)
E
B-R B-R2JUNCTION
CONNECTOR J6
J/B No.2
11J/B No.7 DI-200
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
Actuator Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to drive the door lock motor.
WIRING DIAGRAM
DI4MS-01

N13109
 Relay Block No.7
POWER M-Fuse
1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-201
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check POWER M-fuse.
PREPARATION:
(a) Remove the finish low center panel.
(b) Remove the POWER M-fuse from R/B No.7.
CHECK:
Check continuity of POWER M-fuse.
OK:
Continuity
NG Check for short in all the harness and compo-
nents connected to the POWER M-fuse
(See attached wiring diagram). *1
OK

N12882
ID1
IH1
BJ1
BK1Theft Deterrent ECU
(Door Lock Control Relay)
( ): w/o Theft Deterrent System JUNCTION
CONNECTOR B R
GC
8 IE8 5 4
4 2T3 D63 (4)
T3 D62 (3) J6
JUNCTION
CONNECTOR
C
GG
G
G
GG
G
GC
CACT+
ACT-
B
BID2
IH1
BJ1
BK1 5 4
4 2 Door Lock Motor
Driver's
Rear Left Passenger's
Rear Right R
R
RR
R
R
R IE1
14
R 7
9
2
21
8
6
6
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-203
1996 TERCEL (RM440U)
Door Lock Motor Circuit
CIRCUIT DESCRIPTION
This door lock motor locks and unlocks the door in accordance with signals from the ECU.
WIRING DIAGRAM
DI4MT-02

N15259
Theft Deterrent ECU
(Door Lock Control Relay)
Door Lock Control Switch
Driver's
(Door Lock Control Switch
Passenger's)
( ): w/o Theft Deterrent System IEJ6
JUNCTION
CONNECTORID110
W-B
A
IH13 ID11D9 (10)
T45
D9 (11)
T48L1
UL1 ID12
IH12 LOCK
UNLOCK
LOCK
UNLOCK AA W-B
W-B
W-B
W-B IH1 12
J3
JUNCTION
CONNECTOR A
A1 2
4
3
(3)
(2)R-Y
G-Y
R-Y
G-YR-Y
G-Y
R-Y
G-Y (4) DI-206
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
Door Lock Control Switch Circuit
CIRCUIT DESCRIPTION
When the door lock control switch is pushed to the lock side, Lock terminal of the switch is grounded, and
when the switch is pushed to the unlock side, Unlock terminal is grounded (See wiring diagram below).
WIRING DIAGRAM
DI4MU-02

N12884
Theft Deterrent ECU
Door Key Lock and Unlock Switch
Driver's
J6
JUNCTION
CONNECTORID110
W-B
AID1
D6 (10)
T4 22
LOCK
UNLOCK
AA W-B
W-B
J3
JUNCTION
CONNECTOR2R-Y9
IH111
IH110 ID18
IH1 12
A
ALOCK
UNLOCK Door Key Lock and Unlock Switch
Passenger's
(G-Y) R-W
G-W
R-WW-LW-L
(R-W) W-G
(R-Y)
D6(9)
T46
D6 (11)
T4 16L2
(L1)
UL3
UL2
(UL1) W-G 3
1
3
1 2
IE
( ): w/o Theft Deterrent System W-B
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-209
1996 TERCEL (RM440U)
Door Key Lock and Unlock Switch Circuit
CIRCUIT DESCRIPTION
The door key lock and unlock switch is built in the door key cylinder. When the key is turned to the lock side,
terminal 3 of the switch is grounded and when the key is turned to the unlock side, terminal 1 of the switch
is grounded.
WIRING DIAGRAM
DI4MV-02

I10187
IEW-B
1 Key Unlock Warning Switch
2
LGT420
KSW Theft Deterrent ECU
N14675SR4824
I09773
2
1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-21 1
1996 TERCEL (RM440U)
Key Unlock Warning Switch Circuit
CIRCUIT DESCRIPTION
The key unlock warning switch goes on when the ignition key is inserted in the key cylinder and goes off when
the ignition key is removed.
The ECU operates the key confinement prevention function while the key unlock warning switch is on.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check key unlock warning switch.
PREPARATION:
Disconnect key unlock warning switch connector.
CHECK:
Check continuity between terminals 1 and 2 of key unlock warn-
ing switch connector, when the key is inserted to the key cylin-
der or removed.
OK:
Switch positionTester connectionSpecified condition
ON (Key inserted)1 - 2Continuity
OFF (Key removed)-No continuity
NG Replace key unlock warning switch.
OK
DI4MW-02

N12886
Theft Deterrent ECU J6
JUNCTION
CONNECTOR
ID110
W-BA
ID1
A AW-B
W-B J3
JUNCTION
CONNECTOR2
IH1 A
ADoor Unlock Detection Switch
W-B
Passenger's
Rear Left
Rear Right BJ11
BK11P-L
3
BG
IH1
Y 1
33
T4 15
W-B W-BW-BP-L
P-L 1
1
321
T4 21
T42 P
IE24
Y Y
Y Y
BK13 BJ13 12LSWD
LSWP
LSWR Driver's
W-B W-B
IE
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-213
1996 TERCEL (RM440U)
Door Unlock Detection Switch Circuit
CIRCUIT DESCRIPTION
The door unlock detection switch is built in the door lock motor assembly. This switch is on when the door
lock knob is in the unlock position and off when the lock knob is in the lock position.
The ECU detects the front door lock knob conditions in this circuit. It is used as one of the operating condi-
tions for the key confinement prevention function.
WIRING DIAGRAM
DI4MX-02

DI4N4-02
N12887
Theft Deterrent ECU
5 Theft Deterrent
Indicator Light
(in Combination Meter)
2
IND 12
W-B
IDGR-R
T4 C9
C9
DI-224
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
1996 TERCEL (RM440U)
CIRCUIT INSPECTION
Indicator Light Circuit
CIRCUIT DESCRIPTION
When the theft deterrent system is preparing to set, this circuit lights up the indicator light. When the system
has been set, it continually turns the indicator light on for 1 second and turns it off for 1 second, thus blinking
the indicator light.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check indicator light.
PREPARATION:
Remove combination meter.
CHECK:
Connect positive
lead to terminal C5 and negative  lead to terminal C2 of combination meter connector
then check indicator light comes on.
NG Replace combination meter.
OK