1996 TOYOTA T100 sensor

Downloaded from www.Manualslib.com manuals search engine IG03S−03
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
IG−9
1164 Author: Date:
1996 TOYOTA T100 (RM449U)
CAMSHAFT POSITION SENSOR
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine IG03T−03
P20432
IG−10
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE UPPER RADIATOR HOSE
2. REMOVE NO. 2 TIMING BELT COVER
(a) Remove the high−tension cord clamps from the No. 2 tim-
ing belt cover.
(b) Remove the PS pump hose from the No. 2 timing belt cov-
er clamp.
(c) Remove the 6 bolts and No. 2 timing belt cover.
3. REMOVE CAMSHAFT POSITION SENSOR
(a) Disconnect the camshaft position sensor connector.
(b) Remove the bolts and camshaft position sensor.
Torque:7.8 N·m (80 kgf·cm, 69 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine IG03U−02
− IGNITION (5VZ−FE)CAMSHAFT POSITION SENSOR
IG−11
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−10).

Downloaded from www.Manualslib.com manuals search engine P20434
IG03V−03
IG−12
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
1167 Author: Date:
1996 TOYOTA T100 (RM449U)
CRANKSHAFT POSITION SENSOR
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. REMOVE CRANKSHAFT POSITION SENSOR
(a) Disconnect the crankshaft position sensor connector.
(b) Remove the bolt crankshaft position sensor.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine IG03W−01
P20431
Ohmmeter
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
IG−13
1996 TOYOTA T100 (RM449U)
INSPECTION
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the sensor itself. ”Cold” is from −10°C
(14°F) to 50°C (122°F) and ”Hot” is from 50°C (122°F) to
100°C (212°F).
INSPECT CRANKSHAFT POSITION SENSOR
RESISTANCE
Using an ohmmeter, measure the resistance between termi-
nals.
Resistance:
Cold: 1,630 − 2,740 Ω
Hot: 2,065 − 3,225 Ω
If the resistance is not as specified, replace the crankshaft posi-
tion sensor.

Downloaded from www.Manualslib.com manuals search engine IG03X−02
IG−14
− IGNITION (5VZ−FE)CRANKSHAFT POSITION SENSOR
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−12).

Downloaded from www.Manualslib.com manuals search engine Q06824
Q06823
Q06822
Q10111
MT−8
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION UNIT (4WD)
1996 TOYOTA T100 (RM449U)
8. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 nuts, gasket and oxygen sensor.
(b) Remove the 2 bolts, retainer and gasket.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
(c) Remove the 3 bolts and bracket.
Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
(d) Remove the 3 nuts, front exhaust pipe and 2 gaskets.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
9. REMOVE STARTER
(a) Disconnect the connector and wire from the starter.
(b) Remove the 2 bolts and starter.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
10. RE MO V E STIFFE NE R PLATE (RH AND LH) AND
REAR END PLATE
Remove the 8 bolts, stiffener plate (RH and LH) and rear end
plate.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
11. REMOVE STABILIZER BAR (See page SA−126)
12. JACK UP TRANSMISSION SLIGHTLY
Using a transmission jack, support the transmission.
13. REMOVE CROSSMEMBER
(a) Remove the 4 set bolts of the engine rear mounting.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(b) Remove the 8 bolts and crossmember.
Torque: 95 N·m (970 kgf·cm, 70 ft·lbf)
14. REMOVE TRANSMISSION WITH TRANSFER
(a) Remove the 6 transmission mounting bolts from the en-
gine.
Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
(b) Disconnect the 3 wire clamps from the transmission.
(c) Pull out the transmission with the transfer down and to-
ward the rear.
15. REMOVE ENGINE REAR MOUNTING
Remove the 4 bolts and engine rear mounting.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine AT – AUTOMATIC TRANSMISSION

AUTOMATIC TRANSMISSION SYSTEM AT-1
EXTENSION HOUSING OIL SEAL
(A340E) AT-3
SENSOR ROTOR (A340E) AT-4
SPEEDOMETER DRIVEN GEAR AT-8
VEHICLE SPEED SENSOR AT-10
PARK/NEUTRAL POSITION (PNP)
SWITCH AT-11
VALVE BODY ASSEMBLY AT-12
PARKING LOCK PAWL AT-17
THROTTLE CABLE AT-18
SHIFT LOCK SYSTEM AT-19
AUTOMATIC TRANSMISSION UNIT
(A340E) AT-26
AUTOMATIC TRANSMISSION UNIT
(A340F) AT-33
TORQUE CONVERTER CLUTCH AND
DRIVE PLATE AT-38