1996 TOYOTA T100 oil viscosity

Downloaded from www.Manualslib.com manuals search engine PP0GK−01
PP−36
− PREPARATIONLUBRICATION (3RZ−FE)
1996 TOYOTA T100 (RM449U)
LUBRICANT
ItemCapacityClassification
Engine oil
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change
6.0 liters (6.3 US qts, 5.3 lmp. qts)
5.3 liters (5.6 US qts, 4.7 lmp. qts)
5.0 liters (5.3 US qts, 4.4 lmp. qts)
API grade SH, Energy−Conserving II multigrade
engine oil or ILSAC multigrade engine oil and
recommended viscosity oil, with SAE 5W−30
being preferred engine oil

Downloaded from www.Manualslib.com manuals search engine PP01U−07
− PREPARATIONLUBRICATION (5VZ−FE)
PP−41
1996 TOYOTA T100 (RM449U)
LUBRICANT
ItemCapacityClassification
Engine oil
2WD
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change
4WD
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change
5.9 liters (6.2 US qts, 5.2 lmp. qts)
5.2 liters (5.5 US qts, 4.6 lmp. qts)
5.2 liters (5.5 US qts, 4.6 lmp. qts)
4.9 liters (5.2 US qts, 4.3 lmp. qts)
5.5 liters (5.8 US qts, 4.8 lmp. qts)
4.7 liters (5.0 US qts, 4.1 lmp. qts)
4.4 liters (4.7 US qts, 3.9 lmp. qts)
API grade SH, Energy−Conserving II multigrade
engine oil or ILSAC multigrade engine oil and
recommended viscosity oil, with SAE 5W−30
being preferred engine oil

Downloaded from www.Manualslib.com manuals search engine B00319
Recommended Viscosity (SAE):
10W−30
5W−30 PREFERRED
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
°F −20 0 20 40 60 80 100
°C −29 −18 −7 4 16 27 38
LU0O7−01
− LUBRICATION (3RZ−FE)OIL AND FILTER
LU−1
1109 Author: Date:
1996 TOYOTA T100 (RM449U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SH Energy−Conserving II or SJ,
Energy−Conserving or ILSAC multigrade engine oil.
SAE 5W−30 is the bset choise for your vehicle, for
good fuel economy, and good starting in cold
weather.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the dip-
stick.
If low, check for leakage and add oil up to ”F” mark.
NOTICE:
Do not fill with engine oil above the ”F” mark.
When inserting the dipstick, insert the curved tip of
the dipstick facing the same direction as the curve of
the guide.
If the dipstick gets caught while inserting it, do not
force it in. Reconfirm the direction of the dipstick.
3. REMOVE ENGINE UNDER COVER

Downloaded from www.Manualslib.com manuals search engine LU0817
Recommended Viscosity (SAE):
10W−30
5W−30 PREFERRED
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
LU033−04
P20966SST
P20969
Oil Pressure Gauge
− LUBRICATION (5VZ−FE)OIL AND FILTER
LU−1
1121 Author: Date:
1996 TOYOTA T100 (RM449U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If oil quality is visibly poor, replace it.
Oil grade:
API grade SH Energy−Conserving II or ILSAC multi-
grade engine oil.
SAE 5W−30 is the bset choise for your vehicle, for
good fuel economy, and good starting in cold
weather.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the dip-
stick.
3. CHECK OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the lev-
el gauge. If low, check for leakage and add oil up to the ”F” mark.
If low, check for leakage and add oil up to the ”F” mark.
When inserting the oil dipstick, insert the curved tip of the
dipstick facing the same direction as the curve of the
guide.If the dipstick gets caught while inserting it, do not
force it in. Reconfirm the direction of the dipstick.
4. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816−30010
5. INSTALL OIL PRESSURE GAUGE
6. START ENGINE
Start the engine and warm it up to normal operating tempera-
ture.
7. CHECK OIL PRESSURE
Oil pressure:
At idle speed
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 520 kPa (2.5 − 5.3 kgf/cm
2, 36 − 75 psi)
8. REMOVE OIL PRESSURE GAUGE

Downloaded from www.Manualslib.com manuals search engine MT0501
Down
ClothCounterclockwise
MT04O−02
Q06817
Installation
Front
Select Return Spring
Tip of Shift Lever
− MANUAL TRANSMISSION (R150, R150F)MANUAL TRANSMISSION UNIT (4WD)
MT−7
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE TRANSMISSION SHIFT LEVER
(a) Remove the 4 screws and front console box.
(b) Remove the 4 screws and shift lever boot retainer.
(c) Cover the shift lever cap with a cloth.
(d) Then, pressing down on the shift lever cap, rotate it coun-
terclockwise to remove.
(e) Pull out the shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of the shift lever.
2. REMOVE TRANSFER SHIFT LEVER
Using snap ring pliers, remove the snap ring and pull out the
shift lever.
HINT:
At the time of installation, please refer to the following item.
Apply MP grease to the tip of shift lever.
3. RAISE VEHICLE AND DRAIN TRANSMISSION OIL
Oil grade: API GL−4 or GL−5
Viscosity: SAE 75W−90
Capacity: 2.2 liters (2.3 US qts, 1.9 Imp. qts)
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
4. REMOVE FRONT AND REAR PROPELLER SHAFTS
(See page PR−10)
5. DISCONNECT SPEEDOMETER CABLE
6. DISCONNECT BACK−UP LIGHT SWITCH AND 4WD
INDICATOR SWITCH CONNECTORS
7. DISCONNECT CLUTCH RELEASE CYLINDER AND
LINE
Remove the 4 bolts, release cylinder and line.
Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)

Downloaded from www.Manualslib.com manuals search engine R12169
SST
FA1083
SST
R04344
Less than 5 mm (0.20 in.) SA−44
− SUSPENSION AND AXLEFRONT DIFFERENTIAL REAR OIL SEAL (4WD)
1996 TOYOTA T100 (RM449U)
8. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin-
ion.
SST 09950−30010
(b) Apply light coat of hypoid gear oil on threads of a new
companion flange nut.
(c) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 108 N·m (1,100 kgf·cm, 80 ft·lbf)
9. ADJUST DRIVE PINION PRELOAD
(See page SA−57)
10. STAKE DRIVE PINION NUT
11. INSTALL FRONT PROPELLER SHAFT
(See page PR−16)
12. FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 36 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity: SAE 75W−90
Capacity: 1.86 liters (1.97 US qts, 1.64 lmp. qts)
13. INSTALL ENGINE UNDER COVER

Downloaded from www.Manualslib.com manuals search engine SA0I7−02
RA10720 − 5 mm (0 − 0.20 in.) OilFiller Hole SA−154
− SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. INSTALL NEW GASKET TO AXLE HOUSING
2. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
Install the differential carrier assembly in the axle housing.
Torque: 73 N·m (740 kgf·cm, 54 ft·lbf)
3. INSTALL PROPELLER SHAFT
2WD: See page PR−9
4WD: See page PR−16
4. INSTALL REAR AXLE SHAFTS
(See page SA−135)
5. FILL DIFFERENTIAL WITH DIFFERENTIAL OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 39 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity:
Above −18°C (0°F) SAE 90
Below −18°C (0°F) SAE 80W or 80W − 90
Capacity: 2.35 liters (2.22 US qts, 2.67 lmp.qts)