1996 TOYOTA RAV4 suspension

R10678
SST
− SUSPENSION AND AXLEFRONT AXLE HUB
SA−11
1996 RAV4 (RM447U)
(b) Using SST, disconnect the tie rod end from the steering
knuckle.
SST 09610−20012
7. DISCONNECT LOWER BALL JOINT FROM LOWER
ARM
Remove the bolt and 2 nuts.
Torque: 127 N·m (1,300 kgf·cm, 94 ft·lbf)
8. REMOVE STEERING KNUCKLE WITH AXLE HUB
HINT:
At the time of installation, please refer to the following item.
Coat the threads of the nut’s with engine oil.
NOTICE:
Be careful not to damage the oil seal, boot and ABS speed
sensor rotor.

SA0TB−01
R10677
SST
R10676
SST
R10675
SST
SST
F01922
SST
SA−12
− SUSPENSION AND AXLEFRONT AXLE HUB
1996 RAV4 (RM447U)
DISASSEMBLY
1. REMOVE DUST DEFLECTOR
Using a screwdriver, remove the dust deflector.
2. REMOVE LOWER BALL JOINT
(a) Remove the cotter pin and nut.
(b) Using SST, remove the lower ball joint.
SST 09628−62011
3. REMOVE AXLE HUB
(a) Using SST, remove the axle hub.
SST 09520−00031
(b) Using SST, remove the inner race (outside) from the axle
hub.
SST 09950−40010 (09951−04020, 09952−04010,
09953−04020, 09954−04010, 09955−04060,
09957−04010, 09958−04010),
09950−60010 (09951−00370)
4. REMOVE DUST COVER
Remove the 4 bolts and dust cover.
5. REMOVE OIL SEALS
(a) Using SST, remove the inner oil seal.
SST 09308−00010

F01923
SST
R10731
SST
SST
− SUSPENSION AND AXLEFRONT AXLE HUB
SA−13
1996 RAV4 (RM447U)
(b) Using SST, remove the outer oil seal.
SST 09308−00010
6. REMOVE BEARING FROM STEERING KNUCKLE
(a) Using snap ring pliers, remove the snap ring.
(b) Place the inner race on the outside of the bearing.
(c) Using SST and a press, remove the bearing.
SST 09527−17011, 09950−60010 (09951−00540),
09950−70010 (09951−07150)

SA0TC−02
R10732
SST
R10737
SST
SST
W01224
SST
SST
R10736
SST
SST
R10771
SST
SST SST SA−14
− SUSPENSION AND AXLEFRONT AXLE HUB
1996 RAV4 (RM447U)
REASSEMBLY
1. INSTALL BEARING
(a) Using SST and press, install a new bearing to the steering
knuckle.
SST 09608−32010, 09950−70010 (09951−07150)
(b) Using snap ring pliers, install a new snap ring.
2. INSTALL DUST COVER
Install the dust cover with the 4 bolts.
Torque: 8.3 N·m (85 kgf·cm, 74 in.·lbf)
3. INSTALL NEW OUTER OIL SEAL
(a) Using SST and a hammer, install a new outer oil seal.
SST 09608−32010, 09950−70010 (09951−07150)
(b) Apply MP grease to the oil seal lip.
4. INSTALL FRONT AXLE HUB
Using SST and a press, install the axle hub.
SST 09527−17011, 09950−60010 (09951−00370),
09950−70010 (09951−07150)
5. INSTALL NEW INNER OIL SEAL
(a) Using SST and a hammer, install a new inner oil seal.
SST 09608−32010, 09950−70010 (09951−07150)
(b) Apply MP grease to the oil seal lip.
6. INSTALL DUST DEFLECTOR
Using SST and a hammer, install a new dust deflector.
SST 09316−20011, 09608−32010, 09950−70010
(09951−07150)
HINT:
Align the holes for the ABS speed sensor in the dust deflector
and steering knuckle.

− SUSPENSION AND AXLEFRONT AXLE HUB
SA−15
1996 RAV4 (RM447U)
7. INSTALL LOWER BALL JOINT
(a) Install the lower ball joint and torque the nut.
Torque: 127 N·m (1,300 kgf·cm, 94 ft·lbf)
(b) Install a new cotter pin.

SA0TD−04
SA−16
− SUSPENSION AND AXLEFRONT AXLE HUB
1996 RAV4 (RM447U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−10).
AFTER INSTALLATION, CHECK ABS SPEED SENSOR SIGNAL (See page DI−257) AND FRONT
WHEEL ALIGNMENT (See page SA−4)

SA0TE−01
R10733
SST
R10759
− SUSPENSION AND AXLEFRONT WHEEL HUB BOLT
SA−17
1996 RAV4 (RM447U)
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE FRONT BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
(b) Support the brake caliper securely and remove the disc.
3. REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST 09628−10011
4. INSTALL HUB BOLT
(a) Install a washer and nut to the hub bolt, as shown in the
illustration.
(b) Install the hub bolt with torquing the nut.
5. INSTALL FRONT BRAKE DISC AND CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 107 N·m (1,090 kgf·cm, 79 ft·lbf)
HINT:
Check the disc runout (See page BR−26).
6. INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm 76 ft·lbf)

SA0TF−06
W04172
2WD M/T
Snap RingCenter Bearing Bracket
RH Drive Shaft
Snap RingABS Speed Sensor
Tie Rod End
Cotter Pin
Lock Cap LH Drive Shaft
Boot Clamp
Engine
Under
Cover
3 Door vehicle
64 (650, 47)
5 Door vehicle,
All over fender
vehicle
113 (1,150, 83)


32 (330, 24)
64 (650, 47)
8 (80, 69 in.·lbf)
49 (500, 36)
216 (2,200, 159)
127 (1,300, 94)
Lower Suspension Arm X6
X7
Center Drive Shaft Inner Race Ball Cage Stabilizer Bar Link
Snap Ring
Snap Ring
Dust Cover
Center Bearing Dust Cover
Inboard Joint Tulip Outboard Joint
Shaft No.2 Dust
DeflectorBoot




 
N·m (kgf·cm, ft·lbf)
: Specified torque
Non−reusable part
LH SA−18
− SUSPENSION AND AXLEFRONT DRIVE SHAFT
1996 RAV4 (RM447U)
FRONT DRIVE SHAFT
COMPONENTS