1996 TOYOTA RAV4 wheel size

DI41F−02
− DIAGNOSTICSANTI−LOCK BRAKE SYSTEM
DI−239
1996 RAV4 (RM447U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that code. For details
of each code, turn to the page referred to under the ”See page” for the respective ”DTC No.” in the DTC chart.
HINT:
Using SST 09843−18020, connect the terminals Tc and E1, and remove the short pin.
If any abnormality is not found when inspect each inspection parts, inspect the ECU.
DTC No.
(See page)Detection ItemTrouble Area
11
(DI−246)Open circuit in ABS control (solenoid) relay circuit
ABS control (solenoid) relay
Open or short in ABS control (solenoid) relay circuit
ECU
12
(DI−246)Short circuit in ABS control (solenoid) relay circuit
ABS control (solenoid) relay
B+ short in ABS control (solenoid) relay circuit
ECU
*3 13
(DI−250)Open circuit in ABS control (motor) relay circuit
ABS control (motor) relay
Open or short in ABS control (motor) relay circuit
ECU
14
(DI−250)Short circuit in ABS control (motor) relay circuit
ABS control (motor) relay
B+ short in ABS control (motor) relay circuit
ECU
21
(DI−254)Open or short circuit in 2−position solenoid circuit for right front
wheelABS actuator
Open or short in SFRR or SFRH circuit
ECU
22
(DI−254)Open or short circuit in 2−position solenoid circuit for left front
wheelABS actuator
Open or short in SFLR or SFLH circuit
ECU
23
(DI−254)Open or short circuit in 2−position solenoid circuit for right rear
wheelABS actuator
Open or short in SRRR or SRRH circuit
ECU
24
(DI−254)Open or short circuit in 2−position solenoid circuit for left rear
wheelABS actuator
Open or short in SRLR or SRLH circuit
ECU
*3 31
(DI−257)Right front wheel speed sensor signal malfunction
Right front, left front, right rear or left rear speed sensor
Open or short in each speed sensor circuit
Speed rotor
ECU*3 32
(DI−257)Left front wheel speed sensor signal malfunction
*3 33
(DI−257)Right rear wheel speed sensor signal malfunction
*3 34
(DI−257)Left rear wheel speed sensor signal malfunction
*2 35
(DI−257)Open circuit in speed sensor circuitOpen in speed sensor circuit
*1 37
(DI−261)Some tire is different size from other tiresTire size
ECU
41
(DI−262)Low battery positive voltage
Abnormal high battery positive voltage (2WD Vehicles)
Battery
IC regulator
Open or short in power source circuit
ECU
*2 43
(DI−266)Malfunction in deceleration sensor (constant output)
Deceleration sensor
Wire harness for deceleration sensor system
ECU

EM0EM−03
S01283
B
SST
A
S01358
Oil Pump
S01630
SST
SST
− ENGINE MECHANICALTIMING BELT
EM−15
1996 RAV4 (RM447U)
REMOVAL
1. DISCONNECT PS RESERVOIR AND REMOVE RES-
ERVOIR BRACKET
2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1
3. REMOVE GENERATOR (See page CH−7)
4. REMOVE GENERATOR BRACKET
5. w/ ABS:
REMOVE NO. 3 ABS ACTUATOR BRACKET (See page
BR−40)
6. REMOVE RH FRONT WHEEL
7. REMOVE RH ENGINE UNDER COVER
8. REMOVE PS PUMP DRIVE BELT
(a) Loosen the bolt A.
(b) Using SST and a deep socket wrench, loosen the bolt B.
SST SST09249−63010
(c) Remove the drive belt.
9. SLIGHTLY JACK UP ENGINE
Attach the jack to the oil pan, and raise the engine enough to
remove the weight from the engine mounting on the right side.
10. REMOVE RH ENGINE MOUNTING INSULATOR
11. REMOVE SPARK PLUGS
12. REMOVE CRANKSHAFT PULLEY
(a) Using SST (and bolt), remove the pulley bolt.
SST 09213−54015 (91651−60855 for type A),
09330−00021
Bolt: Part No. 91121−40665 for type B
HINT:
Either of 2 types of pulley may be used, each with its own
bolt size, type A and type B.
When using bolt type B, a plate washer must be inserted
between the bolt and SST.

RS0QA−02
AB0152
SST
− SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS−11
1996 RAV4 (RM447U)
DISPOSAL
HINT:
When scrapping vehicle equipped with an SRS or disposing of
a steering wheel pad (with airbag), always first deploy the air-
bag in accordance with the procedure described below. If any
abnormality occurs with the airbag deployment, contact the
SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.
When disposing of a steering wheel pad with an airbag
deployed in a collision, follow the same procedure given in step
1−(d) in ”DISPOSAL”.
CAUTION:
Never dispose of a steering wheel pad which has an
undeployed airbag.
The airbag produces a sizeable exploding sound
when it deploys, so perform the operation out−of−
doors and where it will not create a nuisance to
nearby residents.
When deploying the airbag, always use the specified
SST (SRS Airbag Deployment Tool). Perform the op-
eration in a place away from electrical noise.
SST 09082−00700
When deploying an airbag, perform the operation at
least 10 m (33 ft) away from the steering wheel pad.
The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes af-
ter deployment.
Use gloves and safety glasses when handling a steer-
ing wheel pad with deployed airbag.
Always wash your hands with water after completing
the operation.
Do not apply water, etc. to a steering wheel pad with
deployed airbag.

R05752
SST
R11852
Weight
R04211
Tires
(3 or more)Inner Diam.
Width RS−16
− SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
1996 RAV4 (RM447U)
(d) Install the SST.
CAUTION:
Place the disc wheel on level ground.
(1) Connect the SST connector to the steering wheel
pad connector.
SST 09082−00700, 09082−00760
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, pro-
vide some slack for the SST wire harness inside the disc
wheel.
(2) Move the SST to at least 10 m (33 ft) away from the
steering wheel pad tied down on the disc wheel.
(e) Cover the steering wheel pad with cardboard box or tires.
Covering method using cardboard box:
Cover the steering wheel pad with the cardboard
box and weight the cardboard box down in 4 places
with at least 190 N (20 kg, 44 lb).
Size of cardboard box:
Must exceed the following dimensions:
x= 460 mm (18.11 in.)
When dimension y of the cardboard box exceeds the
diameter of the disc wheel with tire to which the steer-
ing wheel pad is tied −
x= 460 mm (18.11 in.) + width of tire
y= 650 mm (25.59 in.)
NOTICE:
If a cardboard box smaller than the specified size is used,
the cardboard box will be broken by the shock of the airbag
deployment.
Covering method using tires:
Place at least 3 tires without disc wheel on top of the
disc wheel with tire to which the steering wheel pad
is tied.
Tire size: Must exceed the following dimensions−
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Do not use tires with disc wheels.

SA0T6−02
R03031
R14869
R07928
SA−2
− SUSPENSION AND AXLETIRE AND WHEEL
1996 RAV4 (RM447U)
TIRE AND WHEEL
INSPECTION
1. INSPECT TIRE
(a) Check the tires for wear and proper inflation pressure.
Cold tire inflation pressure
Tire sizeFront
kPa (kgf/cm2
or bar, psi)
Rear
kPa (kgf/cm2 or bar, psi)
3 Door vehicle
215/70R16 99S180 (1.8, 26)180 (1.8, 26)
5 Door vehicle
215/70R16 99S190 (1.9, 28)180 (1.8, 26)
(b) Check the tire runout.
Tire runout: 1.0 mm (0.039 in.) or less
2. ROTATING TIRES
HINT:
See the illustration for where to rotate each tire.
3. INSPECT WHEEL BALANCE
(a) Check and adjust the Off−the−car balance.
(b) If necessary, check and adjust the On−the−car−balance.
Imbalance after adjustment: 13.0 g (0.029 lb) or less

R10734R10735
F02020
Front:
Rear:SA0T7−05
Z03382
SA3213
A
CB
FrontD SA−4
− SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
1996 RAV4 (RM447U)
FRONT WHEEL ALIGNMENT
INSPECTION
1. MEASURE VEHICLE HEIGHT
Tire sizeFront*1
mm (in.)Rear*2
mm (in.)
215/70R16 (2WD)227 (8.94)353 (13.90)
215/70R16 (4WD)227 (8.94)360 (14.17)
*1: Front measuring point:
Measure from the ground to the center of the lower suspension
arm front mounting bolt.
*
2: Rear measuring point:
Measure from the ground to the center of the body side No.1
suspension arm mounting bolt.
NOTICE:
Before inspecting the wheel alignment, adjust the vehicle
height to the specification.
If the vehicle height is not to specification, try to adjust it by
pushing down on or lifting the body.
2. INSTALL CAMBER−CASTER−KINGPIN GAUGE
ONTO VEHICLE OR POSITION VEHICLE ON WHEEL
ALIGNMENT TESTER
Follow the specific instructions of the equipment manufacturer.
3. INSPECT CAMBER, CASTER AND STEERING AXIS
INCLINATION
Tire size: 215/70R16
2WD4WD
Camber
Left−right error−0°20’ ± 45’
(−0.33°± 0.75°)
45’ (0.75°) or less−0°15’± 45’
(−0.25° ± 0.75°)
45’ (0.75°) or less
Caster
Left−right error1°25’ ± 45’
(1.42° ± 0.75°)
45’ (0.75°) or less1°20 ± 45’
(1.33° ± 0.75°)
45’ (0.75°) or less
Steering axis inclination
Left−right error11°00’ ± 45’
(11° ± 0.75°)
45’ (0.75°) or less10°45’ ± 45’
(10.75° ± 0.75°)
45’ (0.75°) or less
If the caster and steering axis inclination are not within the spec-
ification, after the camber has correctly adjusted, recheck the
suspension parts for damaged and/or worn out parts.
4. INSPECT TOE−IN
To e−in
(total)A + B: 0° ± 0’10’ (0° ± 0.17°)
C D: 0 ± 2 mm (0 ± 0.08 in.)
If the toe−in is not within the specification, adjust it by the tie rod
end.