1996 TOYOTA RAV4 steering

W04190
SST
SST Oil Seal
W01253
SST
SST
SSTBushing
R10955
R06172
N00401
SR−52
− STEERINGPOWER STEERING GEAR
1996 RAV4 (RM447U)
(c) Coat a new oil seal lip with power steering fluid.
(d) Using SST, carefully tap in the oil seal.
SST 09950−60010 (09951−00230, 09951−00330,
09952−06010), 09950−70010 (09951−07150)
NOTICE:
Make sure to install the oil seal facing the correct direction.
(e) Coat a new bushing with molybdenum disulfide lithium
base grease.
(f) Using SST, press in the bushing.
SST 09950−60010 (09951−00270, 09951−00340,
09952−06010),09950−70010 (09951−07150)
4. IF NECESSARY, REPLACE TEFLON RING AND O−
RING
(a) Using a screwdriver, remove the teflon ring and O−ring
from the steering rack.
NOTICE:
Be careful not to damage the groove for the teflon ring.
(b) Coat a new O−ring with power steering fluid and install it.
(c) Expand a new teflon ring with your fingers.
NOTICE:
Be careful not to overexpand the ring.
(d) Coat the ring with power steering fluid.
(e) Install the ring to the steering rack and snug it down with
your fingers.

N00402SST
Z01716
N00406
SST
W01254
Screw Extractor
Union Seat
− STEERINGPOWER STEERING GEAR
SR−53
1996 RAV4 (RM447U)
(f) Carefully slide the tapered end of SST over the ring to
seat it.
SST 09630−24014 (09631−24031)
NOTICE:
Be careful not to damage the ring.
5. IF NECESSARY, REPLACE TEFLON RINGS
(a) Using a screwdriver, remove the 4 rings from the control
valve assembly.
NOTICE:
Be careful not to damage the grooves for the ring.
(b) Expand 4 new teflon rings with your fingers.
NOTICE:
Be careful not to overexpand the ring.
(c) Coat the rings with power steering fluid.
(d) Install the rings to the control valve assembly, and snug
them down with your fingers.
(e) Carefully slide the tapered end of SST over the rings to
seat them.
SST 09631−20081
NOTICE:
Be careful not to damage the rings.
6. IF NECESSARY, REPLACE 2 UNION SEATS
(a) Using a screw extractor, remove the union seats.

W01255
Union Seat
Extension Bar
W01202
Cylinder
End Stopper
SR−54
− STEERINGPOWER STEERING GEAR
1996 RAV4 (RM447U)
(b) Using an extension bar and a hammer, tap in 2 new union
seats.
NOTICE:
Before installing the union seat, remove dust sticking to
the rack housing.
7. INSPECT BUSHING
(a) Check for wear and damage on the inside of the bushing
of the cylinder end stopper.
If the bushing is worn or damaged, replace the cylinder end
stopper.
(b) Coat inside of the bushing with molybdenum disulfide lith-
ium base grease.

SR0G8−02
F00873
SST
Oil Seal
SST
W02101
Rack Teeth End
SST
SST Rack Teeth End
W01257
Vinyl Tape
− STEERINGPOWER STEERING GEAR
SR−55
1996 RAV4 (RM447U)
REASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. COAT WITH POWER STEERING FLUID OR MOLYBDE-
NUM DISULFIDE LITHIUM BASE GREASE
(See page SR−44)
2. INSTALL OIL SEAL
(a) Coat a new oil seal lip with power steering fluid.
(b) Using SST, press in the oil seal.
SST 09950−60010 (09951−00230, 09951−00400,
09952−06010), 09950−70010 (09951−07360)
NOTICE:
Make sure to install the oil seal facing the correct
direction.
Take care that the oil seal does not get reversed as
you install it.
3. INSTALL STEERING RACK
(a) Install SST to the rack.
HINT:
If necessary, scrape the burrs off the rack teeth end and bur-
nish.
SST 09631−16020
(b) Coat SST with power steering fluid.
(c) Install the rack into the rack housing.
(d) Remove the SST.
4. INSTALL OIL SEAL
(a) Coat a new oil seal lip with power steering fluid.
(b) To prevent oil seal lip damage, wind vinyl tape on the
steering rack end, and apply power steering fluid.
(c) Install the oil seal by pushing it into the rack housing, with-
out tilting.
NOTICE:
Make sure to install the oil seal facing the correct direction.

W01258
SST
W01259
SST
Bearing
W04191
SST
Oil SealPress SR−56
− STEERINGPOWER STEERING GEAR
1996 RAV4 (RM447U)
5. INSTALL CYLINDER END STOPPER
(a) Install the stopper into the rack housing.
(b) Using snap ring pliers, install a new snap ring to the rack
housing.
6. AIR TIGHTNESS TEST
(a) Install SST to the union of the rack housing.
SST 09631−22030
(b) Apply 53 kPa (400 mmHg, 15.75 in.Hg) of vacuum for
about 30 seconds.
(c) Check that there is no change in the vacuum.
If there is change in the vacuum, check the installation of the oil
seals.
7. INSTALL CONTROL VALVE ASSEMBLY
(a) Coat the teflon rings with power steering fluid.
(b) Install the control valve assembly into the rack housing.
NOTICE:
Be careful not to damage the teflon rings and oil seal.
8. INSTALL BEARING
Using SST, press in a new bearing.
SST 09612−22011
9. INSTALL OIL SEAL
(a) Coat a new oil seal lip with power steering fluid.
(b) Using SST and a press, press in the oil seal.
SST 09612−22011
NOTICE:
Make sure to install the oil seal facing the correct direction.
(c) Using snap ring pliers, install a new snap ring to the rack
housing.
10. INSTALL DUST COVER
11. INSTALL BEARING
Install the spacer and a new bearing into the rack housing.

W01262
SST
W01263
SST
Spacer
Lock NutBC
A
W04192
12°
Hexagon Wrench
W01265
SST
− STEERINGPOWER STEERING GEAR
SR−57
1996 RAV4 (RM447U)
12. INSTALL LOCK NUT
(a) Using SST to stop the control valve shaft rotating, torque
a new nut.
SST 09616−00010
Torque: 12 N·m (125 kgf·cm, 9 ft·lbf)
(b) Turn C of SST to obtain dimension A, then set SST, as
shown.
SST 09613−12020
Dimension A: 16.5 − 17.0 mm (0.65 − 0.67 in.)
(c) Stake the nut by turning B of SST until it touches the
spacer of SST.
13. INSTALL RACK HOUSING CAP
(a) Apply sealant to 2 or 3 threads of the cap.
Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Torque the cap.
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
14. INSTALL RACK GUIDE SEAT, RACK GUIDE, RACK
GUIDE SPRING AND RACK GUIDE SPRING CAP
(a) Install the seat to the guide.
(b) Apply sealant to 2 or 3 threads of the cap.
Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Temporarily install the cap.
15. ADJUST TOTAL PRELOAD
(a) To prevent the steering rack teeth from damaging the oil
seal lip, temporarily install the RH and LH rack ends.
(b) Using a hexagon wrench (21 mm), torque the rack guide
spring cap.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Using a hexagon wrench (21 mm), return the cap 12°.
(d) Using SST, turn the control valve shaft right and left 1 or
2 times.
SST 09616−00010
(e) Using a hexagon wrench (21 mm), loosen the cap until the
rack guide spring is not functioning.

W01266
SST
Hexagon Wrench
W01267SSTFulcrum
Length
W01268
Rack Groove
W01269
SSTFulcrum
Length SR−58
− STEERINGPOWER STEERING GEAR
1996 RAV4 (RM447U)
(f) Using SST, a torque wrench and hexagon wrench (21
mm), tighten the cap until the preload is within the specifi-
cation.
SST 09616−00010
Preload (turning):
0.8 − 1.3 N·m (8 − 13 kgf·cm, 6.9 − 11.3 in.·lbf)
16. INSTALL RACK GUIDE SPRING CAP LOCK NUT
(a) Apply sealant to 2 or 3 threads of the nut.
Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Using a hexagon wrench (21 mm) to stop the rack guide
spring cap rotating, and using SST, torque the nut.
SST 09922−10010
Torque: 32 N·m (330 kgf·cm, 24 ft·lbf)
NOTICE:
Use SST 09922−10010 in the direction shown in the illustra-
tion.
HINT:
Use a torque wrench with a fulcrum length of 345 mm (13.58
in.).
(c) Recheck the total preload.
SST 09616−00010
Preload (turning):
0.8 − 1.3 N·m (8 − 13 kgf·cm, 6.9 − 11.3 in.·lbf)
(d) Remove the RH and LH rack ends.
17. INSTALL RH AND LH CLAW WASHERS AND RACK
ENDS
(a) Install a new washer, and temporarily install the rack end.
HINT:
Align the claws of the washer with the steering rack grooves.
(b) Using a spanner (22 mm) to hold the steering rack steady,
and using SST, torque the rack end.
SST 09922−10010
Torque: 60 N·m (615 kgf·cm, 44 ft·lbf)
NOTICE:
Use SST 09922−10010 in the direction shown in the illustra-
tion.
HINT:
Use a torque wrench with a fulcrum length of 345 mm (13.58
in.).

W01270
Brass Bar
W01261
W01271
2 mm
(0.08 in.)
W01272
SST
Fulcrum
Length
− STEERINGPOWER STEERING GEAR
SR−59
1996 RAV4 (RM447U)
(c) Using a brass bar and a hammer, stake the washer.
NOTICE:
Avoid any impact to the rack.
18. INSTALL GROMMET
Install the grommet to the rack housing No.1 bracket.
19. INSTALL RACK HOUSING NO.1 BRACKET
(a) Align the matchmarks on the bracket and housing.
(b) Torque the bolt.
Torque: 61 N·m (620 kgf·cm, 45 ft·lbf)
20. INSTALL RH AND LH RACK BOOTS, CLAMPS AND
CLIPS
(a) Make sure that the steering rack hole is not clogged with
grease.
HINT:
If the hole is clogged, the pressure inside the boot will change
after it is assembled and the steering wheel turned.
(b) Install the boot.
NOTICE:
Be careful not to damage or twist the boot.
(c) Tighten the clamp, as shown in the illustration.
21. INSTALL RH AND LH TIE ROD ENDS AND LOCK NUTS
(a) Screw the lock nut and tie rod end onto the rack end until
the matchmarks are aligned.
(b) After adjusting toe−in, torque the nut
(See page SA−4).
Torque: 56 N·m (570 kgf·cm, 41 ft·lbf)
22. INSTALL 2 TURN PRESSURE TUBES
(a) Using SST, install the tube.
SST 09633−00020
Torque: 23 N·m (234 kgf·cm, 17 ft·lbf)
HINT:
Use a torque wrench with a fulcrum length of 250 mm
(9.84 in.).
This torque value is effective in case that SST is parallel
to a torque wrench.
(b) Torque the union bolt with a new gasket on each side of
the tube.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)