Page 4 of 1354
AX0T5−01
Q06565
Q07898
Q07907
Neutral Basic
Line
Groove
Q07906
AX−4
− AUTOMATIC TRANSAXLE (A241E)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL PARK/NEUTRAL POSITION SWITCH
(a) Temporarily install the park/neutral position switch with
the 2 bolts.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Adjust the park/neutral position switch (See page
DI−127).
HINT:
Align the groove and park/neutral basic line.
(e) Tighten the 2 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(f) Install the shift control lever with the nut.
(g) Connect the control cable with the nut.
Torque: 13 N·m (135 kgf·cm, 10 ft·lbf)
5. CONNECT PARK/NEUTRAL POSITION SWITCH CON-
NECTOR
6. INSTALL NO.2 ENGINE UNDER COVER
Page 6 of 1354
AT8584
AT8586
Z11664
B A
B
B A
B A
A A CA
AT3327
Q06411
BA AX−6
− AUTOMATIC TRANSAXLE (A241E)VALVE BODY ASSEMBLY
1996 RAV4 (RM447U)
6. REMOVE MANUAL DETENT SPRING
Remove the bolt and manual detent spring.
7. REMOVE 3 SOLENOID CONNECTORS
8. REMOVE VALVE BODY
(a) Disconnect the throttle cable.
(b) Remove the 11 bolts and wire retainer.
Bolt length:
Bolt A: 20 mm (0.79 in.)
Bolt B: 30 mm (1.18 in.)
Bolt C: 55 mm (2.17 in.)
(c) Disconnect the manual valve connecting rod.
(d) Remove the valve body.
9. REMOVE 3 SOLENOID VALVES
(a) Remove the 3 solenoid valves.
(b) Remove the O−rings from each of the solenoid valves.
10. INSTALL SHIFT SOLENOID VALVE
(a) Coat new O−rings with ATF and install them to the each
of the solenoid valve.
(b) Install the 3 shift solenoid valves with the 2 bolts.
Torque:
Bolt A: 6.4 N·m (65 kgf·cm, 56 in.·lbf)
Bolt B: 10 N·m (100 kgf·cm, 7 ft·lbf)
Page 14 of 1354
AX0T8−01
Z18886
RH Drive Shaft
LH Drive Shaft Snap Ring
64 (650, 47)
Cotter Pin
Lock Cap
216 (2,200, 159)
Gasket
49 (500, 36)
7.0 (75, 65 in.·lbf)
62 (630, 46)
48 (490, 35)
Front Exhaust PipeEngine Mounting
Center MemberPS Gear Assembly
Front Suspension Crossmember
Assembly with Stabilizer Bar
RH Engine Under Cover
LH Engine Under Cover
137 (1,400, 101)
206 (2,100, 152)
127 (1,300, 94)
72 (730, 53)
73 (740, 54)
N·m (kgf·cm, ft·lbf)
: Specified torque
Non−reusable part
113 (1,150 83)
Cotter Pin
Gasket
35 (360, 26)
64 (650, 47)
64 (650, 47)
19 (194, 14)
25 (250, 18)
46 (470, 34)
27 (280, 20)
25 (250, 18)
9.0 (95, 78 in.·lbf)
64 (650, 47)
9.0 (95, 78 in.·lbf)
37 (380, 27)
13 (135, 10)
39 (400, 29)64 (650, 47)
GasketStarterEngine Wire
Clamp Plug for Line
Pressure Test
Shift Control
Cable ClipRear End Plate Stiffener Platex 6 Torque Converter
ClutchEngine Coolant Reservoir TankABS RelayAir Intake Connector
Air Cleaner
Case Assembly AX−14
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
AUTOMATIC TRANSAXLE UNIT
COMPONENTS
Page 16 of 1354
Q08764
Q08765
Q08766
Q08767
AX−16
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
9. REMOVE ENGINE LEFT MOUNTING BOLT AND NUTS
Torque:
Bolt: 64 N·m (650 kgf·cm, 47 ft·lbf)
Nut: 64 N·m (650 kgf·cm, 47 ft·lbf)
10. REMOVE LEFT AND RIGHT ENGINE UNDER COVERS
11. DRAIN ATF
12. REMOVE LEFT AND RIGHT DRIVE SHAFTS
(See page SA−20)
13. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 bolts and gasket from the exhaust pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used gasket with new gasket.
(b) Remove the 3 nuts, front exhaust pipe and gasket.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used nuts and gasket with new nuts and gasket.
14. DISCONNECT SHIFT CONTROL CABLE
(a) Remove the nut from the control shaft lever.
Torque: 13 N·m (135 kgf·cm, 10 ft·lbf)
(b) Remove the clip and disconnect the control cable.
(c) Remove the 2 shift cable mounting bolts.
Torque: 7.0 N·m (75 kgf·cm, 65 in.·lbf)
Page 27 of 1354
Q08738
AX128−01
Q06066
Q06109
Q06077NRP AX−6
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft with the 2 bolts and nut.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Temporarily install the manual valve lever shaft.
(e) Turn the lever counterclockwise until it stops, then turn it
clockwise 2 notches.
(f) Remove the shaft control lever.
Page 453 of 1354
OR0028
Q06076
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A241E)
DI−133
1996 RAV4 (RM447U)
Fluid type: ATF DEXRON ®II
NOTICE:
Do not overfill.
(b) Check the fluid condition.
If the fluid smells burnt or is black, replace it.
(c) Replace the fluid.
(1) Remove the drain plug and drain the fluid.
(2) Reinstall the drain plug securely.
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Drain and refill: 3.3 liters (3.5 US qts, 2.9 lmp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add
fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem-
perature 70 − 80°C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transaxle.
If there are leaks, it is necessary to replace O−rings, gaskets,
oil seals, plugs or other parts.
(e) Inspect and adjust throttle cable.
(1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable end
and stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not within the standard, adjust the cable by the
adjusting nuts.
Page 456 of 1354
DI−136
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A241E)
1996 RAV4 (RM447U)
9. HYDRAULIC TEST
Measure the line pressure.
NOTICE:
Do the test at normal operating ATF temperature 50 − 80°C (122 − 176°F).
The line pressure test should always carried out in pairs. One technician should observe the
conditions of wheels or wheel stoppers outside the vehicle while the other is doing the test.
Be careful to prevent SST’s hose from interfering with the exhaust pipe.
(1) Warm up the ATF.
(2) Remove the teat plug on the transaxle case left side and connect SST (See page AX−14. for the
location to connect SST).
SST SST 09992−00094 (09992−00230, 09992−00270)
(3) Chock the 4 wheels.
(4) Fully apply the parking brake.
(5) Start the engine and check idling speed.
(6) Keep your left foot pressed firmly on the brake pedal and shift into the D position.
(7) Measure the line pressure when the engine is idling.
(8) Fully depress the accelerator pedal. Quickly read the highest line pressure when engine speed
reaches stall speed.
NOTICE:
Release the accelerator pedal and stop test if the wheels being to rotate before the engine speed
reaches specified stall speed.
(9) In the same way, do the teat in R position.
Specified line pressure:
ConditionD position kPa (kgf/cm2, psi)R position kPa (kgf/cm2, psi)
Idling353 − 422 (3.6 − 4.3, 51 − 61)598 − 804 (6.1 − 8.2, 87 − 117)
Stall824 − 971 (8.4 − 9.9, 119 − 141)1,530 − 1,780 (15.6 − 18.1, 222 − 257)
If the measured pressures are not up to specified values, recheck the throttle cable adjustment and do a
retest.
Evaluation:
ProblemPossible cause
If the measured value in all positions are higher.
Throttle cable out of adjustment
Throttle valve defective
Regulator valve defective
If the measured values in all positions are lower.
Throttle cable out of adjustment
Throttle valve defective
Regulator valve defective
Oil pump defective
U/D direct clutch defective
If pressure is low in the D position only.D position circuit fluid leakage
Forward clutch defective
If pressure is low in the R position only.
R position circuit fluid leakage
Direct clutch defective
1st and reverse brake defective
Page 502 of 1354
D00697
Ok if hot
Add if hot
AT4252
0 − 1 mm
D02248
DI−182
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
1996 RAV4 (RM447U)
(f) Check the fluid leaks.
Check for leaks in the transmission and transfer.
If there are leaks, it is necessary to repair or replace O − rings,
FIPG’s, oil seals or other parts.
(g) Inspect and adjust the throttle cable.
(1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Loosen the adjustment nuts.
(4) Adjust the outer cable so that the distance between
the end of the boot and stopper on the cable is as
standard.
Standard boot and cable stopper distance:
0 − 1 mm (0 − 0.04 in.)
(5) Tighten the adjusting nuts.
(6) Recheck the adjustments.
(h) Adjust the shift control cable.
(1) Loosen the nut on the lever.
(2) Push the manual lever fully toward the right side of
the vehicle.
