1996 TOYOTA RAV4 terminals

AX0T7−02
Z19320
STPSLS
+
P2
IG
ACC
KLS
+EP1
P
SLS−
Wire Harness Side ABC
AT5027
AT5029
Battery AX−12
− AUTOMATIC TRANSAXLE (A241E)SHIFT LOCK SYSTEM
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
ConnectorTerminalMeasuring conditionVoltage (V)
A
5 − 4 (ACC − E)Ignition switch ACC10 − 14
1 − 4 (IG − E)Ignition switch ON10 − 14
2 − 4 (STP − E)Depress brake pedal10 − 14
6 − 4 (KLS+ − E)
2. Ignition switch ACC and P position0
3. Ignition switch ACC and except P position7.5 − 11
4. (After−approx. 1 second)5.5 − 10
B1 − 2 (SLS+ − SLS−)
1. Ignition switch ON and P position0
2. Depress brake pedal8.5 − 14
3. Except P position0
C
1 − 2 (P1 − P)1. Ignition switch ON, P position and depress brake pedal0
2. Shift except P position under condition above10 − 14
3 − 2 (P2 − P)1. Ignition switch ACC and P position10 − 14
2. Shift except P position under condition above0
2. INSPECT SHIFT LOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between the
terminals.
Standard resistance: 26 − 33 Ω
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between the terminals.
Check that the solenoid can be heard operating.
If solenoid operation is not as specified, replace the solenoid.

Q09052
21
Q09053
21
Z193392 (P)1 (P2)
3 (P1)
− AUTOMATIC TRANSAXLE (A241E)SHIFT LOCK SYSTEM
AX−13
1996 RAV4 (RM447U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between the
terminals.
Standard resistance: 12.5 − 16.5 Ω
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between the terminals.
Check that the solenoid can be heard operating.
If solenoid operation is not as specified, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that there is continuity between each terminal.
Shift positionTester connectionSpecified value
P position (Release button
is not pushed)2 − 3 (P − P1)Continuity
P position (Release button
is pushed)2 − 3 (P − P1)
2 − 1 (P − P2)Continuity
R, N, D, 2, L position2 − 1 (P − P2)Continuity
If continuity is not as specified, replace the switch.

AX0ZJ−02
Z19320
STPSLS
+
P2
IG
ACC
KLS
+EP1
P
SLS−
Wire Harness Side ABC
AT5027
AT5029
Battery AX−16
− AUTOMATIC TRANSAXLE (A540H)SHIFT LOCK SYSTEM
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
ConnectorTerminalMeasuring conditionVoltage (V)
A
1 − 3 (ACC − E)IG SW ACC10 − 14
5 − 3 (IG − E)IG SW ON10 − 14
4 − 3 (STP − E)Depress brake pedal10 − 14
2 − 3
(KLS+ − E)
3. IG SW ACC and shift lever at P position0
4. Shift lever at R, N, D, 2, L position7.5 − 11
5. (after approx 1 second)5.5 − 10
B2 − 1
(SLS+ − SLS−)
1. IG SW ON and shift lever at P position0
2. Depress brake pedal8.5 − 14
3. Except P position0
C
3 − 2
(P1 − P)1. IG SW ON, shift lever at P position and depress brake
pedal0
2. Shift except P position under condition above10 − 14
1 − 2
(P2 − P)1. IG SW ACC and shift lever at P position10 − 14
2. Shift except P position under condition above0
2. INSPECT SHIFT LOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure resistance between the ter-
minals.
Standard resistance: 26 − 33 Ω
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between the terminals.
Check that the solenoid can be heard operating.
If the solenoid does not operated, replace the solenoid.

Q09052
21
Q09053
21
Z193392 (P)1 (P2)
3 (P1)
− AUTOMATIC TRANSAXLE (A540H)SHIFT LOCK SYSTEM
AX−17
1996 RAV4 (RM447U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure resistance between the ter-
minals.
Standard resistance: 12.5 − 16.5 Ω
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between the terminals.
Check that the solenoid can be heard operating.
If the solenoid does not operated, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that there is continuity between each terminal.
Shift positionTester connectionSpecified value
P position (Release button
is not pushed)2 − 3
(P − P1)Continuity
P position (Release button
is pushed)
2 − 3
(P − P1)
2 − 1
(P − P2)
Continuity
R, N, D, 2, L position2 − 1
(P − P2)Continuity
If continuity is not as specified, replace the switch.

BE1MW−01
Z17623
HEAD
TA I L
OFFRight
LeftFlash
8
7
17 16
1413
Z13558
3
4
21
3
4 2
1
Z05657
3 21 3
21
55
− BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE−15
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
TAIL14 − 16Continuity
HEAD13 − 14 − 16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
Flash7 − 8 − 16Continuity
Low beam16 − 17Continuity
High beam7 − 16Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant3 − 4Continuity
Apply B+ between
terminals 3 and 4.1 − 2Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.3 − 5Continuity
If continuity is not as specified, replace the relay.
5. Light−on Warning System:
INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and 12, the negative (−) lead to terminals 10.
(b) Check that the buzzer sounds when the negative (−) lead
from the battery is connected to terminal 6.
If operation is not as specified, replace the relay.
6. INSPECT DOOR COURTESY SWITCH CONTINU-
ITY(See pageBE−22)

BE0JA−01
Z17622
Right
Left
1 2 3
Z07679
2 4
5 1 3
7 96
8 10
BE1843
3
2
1 BE−20
− BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turn1 − 2Continuity
Neutral−No continuity
Right turn2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HAZARD WARNING SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Switch OFF7 − 10Continuity
Switch ON4 − 5 − 6 − 9
7 − 8Continuity
Illumination circuit2 − 3Continuity
If continuity is not as specified, replace the switch.
3. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash 60 or 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashing will be more than 140 per minute.
If operation is not as specified, replace the flasher.

N20864
Washer 1
ON
OFFINT
Washer 2
1 2
10
16
Z09992
Relay Side
1
2
3 4
5 6
N05767
Battery Voltage
No Voltage3 4
6
5
N05768
Within 9
to 15
Seconds2
4
53 BE−30
− BODY ELECTRICALWIPER AND WASHER SYSTEM
1996 RAV4 (RM447U)
4. INSPECT REAR WIPER AND WASHER SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
Washer 12 − 16Continuity
Wiper OFF−No continuity
Wiper INT10 − 16Continuity
Wiper ON1 − 16Continuity
Washer 21 − 2 − 16Continuity
If continuity is not as specified, replace the switch.
5. INSPECT REAR WIPER RELAY CONTINUITY
(a) Check that no continuity exists between terminals 3 and
4.
(b) Check that continuity exists between terminals 4 and 5.
If continuity is not as specified, replace the relay.
6. INSPECT REAR WIPER RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (−) lead to terminal 6.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 5 and the negative (−) lead to terminal 6, check that
the meter needle indicates 0 volts.
(c) Connect the positive (+) lead from the voltmeter to termi-
nal 4 and the negative (−) lead to terminal 6, check that
the meter needle indicates battery positive voltage.
If operation is not as specified, replace the relay.
7. INSPECT REAR WIPER RELAY INTERMITTENT OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative (−) lead to terminal 2 more than 2 se-
conds.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 4 and the negative (−) lead to terminal 2.

N05769
1 3
N05770
1 2
N05771
1 3
N05772
1 3
65
− BODY ELECTRICALWIPER AND WASHER SYSTEM
BE−31
1996 RAV4 (RM447U)
(c) After disconnecting the positive (+) lead from terminal 5
connect it to terminal 3, and than, check that the meter
needle rises from 0 volts to battery positive voltage within
9 to 15 seconds.
If operation is not as specified, replace the relay.
8. INSPECT FRONT WIPER MOTOR OPERATION
(a) Inspect the motor operation at low speed.
Connect the positive (+) lead from the battery to terminal
3 and the negative (−) lead from the battery to terminal 1,
check that the motor operates at low speed.
If operation is not as specified, replace the motor.
(b) Inspect the motor operation at high speed.
Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead from the battery to terminal 1,
check that the motor operates at high speed.
If operation is not as specified, replace the motor.
(c) Inspect the motor operation when stopping it.
(1) Operate the motor at low speed and stop the motor
operation anywhere except at the stop position by
disconnecting the positive (+) lead from terminal 3.
(2) Connect terminals 3 and 5.
(3) Connect the positive (+) lead from the battery to ter-
minal 6 and negative (−) lead from the battery termi-
nal 1, check that the motor stops running at the stop
position after the motor operates again.
If operation is not as specified, replace the motor.