1996 TOYOTA LAND CRUISER Bolt

BO48P−01
N14081
N14075
BO−38
−
BODY WHEEL OPENING MOULDING
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT FENDER WHEEL OPENING MOULDING
(a) Remove the charcoal canister.
(b) Remove the air cleaner case assembly.
(c) Remove the cool air intake duct.
(d) Remove the front wheel.
(e) Remove the front mudguard.
(f) Remove the front bumper extension.
(g) Remove the 4 nuts from engine room inside service hole.
(h) Remove the 2 screws.
(i) Remove the front wheel opening extension.
2. REAR DOOR SIDE: REMOVE REAR WHEEL OPENING MOULDING
Remove the 2 bolts and moulding.
3. REMOVE REAR WHEEL OPENING MOULDING
(a) Remove the mud guard, bumper extention and back door
scuff plate.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48Q−01
N14082
BO−40
−
BODY WHEEL OPENING MOULDING
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FRONT WHEEL OPENING MOULDING
(a) Install the front wheel opening moulding.
(b) Install the 4 nuts from the service hole of the engine room
inside.
(c) Install the 2 screws.
(d) Front bumper extension
(e) Front mudguard
(f) Front wheel
(g) Cool air intake duct
(h) Air cleaner case assembly
(i) Charcoal canister
2. INSTALL QUARTER OUTSIDE MOULDING
Install the quarter outside moulding with the 2 bolts.
3. INSTALL REAR WHEEL OPENING MOULDING
(a) Install the rear wheel opening moulding with the 2 nuts.
(b) Install the screw.
(c) Install the quarter trim LH.
(d) Install the quarter trim RH.
(e) Install the back door scuff plate.
(f) Install the rear bumper extension.
(g) Install the rear mudguard.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO4033
−
BODY SLIDING ROOF
BO−65
1996 LAND CRUISER (RM451U)
27. REMOVE DRIVE GEAR ASSEMBLY
(a) Remove the bolt and drive gear control relay, then discon-
nect the connector.
(b) Remove the 2 bolts and bracket.
(c) Remove the 4 bolts and drive gear assembly, then discon-
nect the connector.
28. REMOVE SLIDING ROOF GARNISHES
Using a screwdriver, pry loose the 2 clips and remove the inner
side garnish.
29. REMOVE SLIDING ROOF GLASS
(a) Remove the 6 nuts and shims.
HINT:
Make sure of the number of shims.
(b) Pull the glass upward to remove it.
30. REMOVE DRIP CHANNEL
(a) Remove the 2 screws.
(b) Pull the channel forwards to remove it.
31. REMOVE WIND DEFLECTOR
Remove the 4 screws and wind deflector.
32. REMOVE SLIDING ROOF HOUSING
(a) Disconnect the drain hose.
(b) Remove the 3 nuts, 12 screw and housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO4047
Point Marks
BO−66
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
33. ADJUST DRIVE RAIL
HINT:
Adjust the drive rail to a closed and tilted down position.
Using a screwdriver, slide the link forward or backward to align
the 2 marks, as shown.
34. ADJUST AND INSTALL DRIVE GEAR ASSEMBLY
(a) Remove the screw and cam plate cover.
(b) Remove the large screw, washers and shims.
(c) Turn the drive shaft by screwdriver to align the housing
and gear point mark, as shown.
(d) Install the cam plate cover with the screw.
(e) Install the drive gear assembly with 4 bolts.
(f) Connect the connector.
35. INSTALL DRIVE GEAR CONTROL RELAY AND BRACKET
(a) Install the bracket with 2 bolts.
(b) Install the drive gear control relay with the bolt, then con-
nect the connector.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY INSTRUMENT PANEL
BO−77
1996 LAND CRUISER (RM451U)
15. REMOVE CENTER CLUSTER FINISH PANEL WITH
HEATER CONTROL ASSEMBLY
(a) Using a screwdriver, take off the 2 claws, then remove the
cup holder hole cover.
HINT:
Tape the screwdriver tip before use.
(b) Take off the ashtray.
(c) Remove the center cluster finish panel with heater control
assembly, then disconnect the connectors.
(d) Remove the 2 screws and heater control assembly from the center cluster finish panel.
16. REMOVE RADIO
17. REMOVE GLOVE COMPARTMENT DOOR
18. REMOVE SPEAKER PANEL AND SPEAKER
19. REMOVE FRONT AND REAR CONSOLE BOX
20. DISCONNECT AIRBAG CONNECTOR
(a) Remove the airbag connector from the airbag bracket.
NOTICE:
When handling the airbag connector , take care not to dam-
age the airbag wire harness.
(b) Disconnect the airbag connector.
21. REMOVE INSTRUMENT PANEL
(a) Remove the 5 screws and 9 bolts.
(b) Remove the instrument panel. Torque: 20 N·m (210 kgf·cm, 15 ft·lbf) for passenger
airbag bolts
22. REMOVE INSTRUMENT PANEL REINFORCEMENT
(a) Remove the 2 bolts and lower instrument panel reinforce-
ment.
(b) Remove the 2 bolts, 2 nuts and No. 1 brace.
(c) Remove the 4 bolts, 4 nuts and instrument panel rein- forcement.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO399−01
BO−78
−
BODY INSTRUMENT PANEL
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE GLOVE COMPARTMENT DOOR RE- INFORCEMENT
2. REMOVE NO. 4 HEATER TO REGISTER DUCT
3. REMOVE NO. 5 HEATER TO REGISTER DUCT
4. REMOVE NO. 2 REGISTER
5. REMOVE GLOVE COMPARTMENT DOOR LOCK STRIKER PLATE
6. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY (See page RS−22 )
(a) Remove the 4 bolts and 2 nuts, and remove front passen-
ger airbag assembly.
(b) Pry up the 6 clips shown in the illustration and remove the airbag door.
CAUTION:
Do not store the front passenger airbag assembly
with the airbag deployment direction facing down.
Never disassemble the front passenger airbag as-
sembly.
7. REMOVE NO. 3 CONSOLE MOUNTING BRACKET
8. REMOVE NO. 1 HEATER TO REGISTER DUCT
9. REMOVE NO. 2 STAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48R−01
BO−84
−
BODY FRONT SEAT (Power Adjuster Type)
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE FRONT SEAT HEADREST
2. REMOVE SIDE SUPPORT ADJUSTER KNOB
Using a screwdriver, remove the snap ring and side support ad-
juster knob.
3. REMOVE SEATBACK BOARD
(a) Remove the 2 screws.
(b) Slide the board downward to remove it.
4. REMOVE FRONT SEATBACK ASSEMBLY
(a) Using a hog ring pliers, remove the hog ring backward of seatback.
(b) Remove the 4 bolts and front seatback assembly. Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
5. REMOVE FRONT SEAT CUSHION INNER SHIELD
6. REMOVE FRONT SEAT INNER BELT
7. REMOVE FRONT SEAT CUSHION SHIELD
8. REMOVE FRONT SEAT CUSHION
(a) Remove the 4 bolts.
Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
(b) Disconnect the connector, then remove the front seat cushion.
9. REMOVE SEAT CUSHION REAR PROTECTOR
10. REMOVE RECLINING ADJUSTER INSIDE COVER
Remove the 4 screws and reclining adjuster inside cover LH
and RH.
11. REMOVE POWER ADJUST FRONT SHIELD
Remove the 2 screws and front shield.
12. REMOVE SLIDE MOTOR
(a) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
4 housing bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(b) Hold the front seat horizontal jack screw with a plier, and remove the 2 nuts and 2 washers.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of installation, apply adhesive to nut. Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY FRONT SEAT (Power Adjuster Type)
BO−85
1996 LAND CRUISER (RM451U)
(c) Remove the 4 screws and 2 vertical adjuster bushes.
(d) Remove the 4 bolts, slide motor, front seat slide housing
and front seat horizontal jack screw.
Torque: 19 N·m (200 kgf·cm, 14 ft·lbf)
(e) Loosen the seat adjuster nut, then remove the slide mo- tor.
13. REMOVE REAR VERTICAL MOTOR
(a) Remove the 2 E −rings, and disconnect the No. 1 vertical
seat link.
(b) Remove the 4 bolts, vertical rod hold bracket RH and ver-
tical rod hold bracket LH.
Torque: 20 N·m (210 kgf·cm, 15 ft·lbf)
(c) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
2 housing support bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(d) Hold the No. 2 vertical travel jack screw with a plier, re- move the nut and washer.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of reassembly, apply adhesive to nut.
Part No. 08833− 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010