1996 TOYOTA LAND CRUISER Bolt

AC2RC−01
N13975
AC−40
−
AIR CONDITIONING RECEIVER
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
HINT:
At the time of installation, refer to the following procedure.
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of
refrigerant.
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
2. DISCONNECT 2 LIQUID TUBES FROM RECEIVER
Remove the 2 bolts and both tubes.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate 2 new O −rings with com-
pressor oil and install the tubes.
3. REMOVE RECEIVER FROM RECEIVER HOLDER
Remove the holder bolt and pull the receiver down ward.
HINT:
If receiver was replaced, add compressor oil to compressor. Add 10 cc (0.35 fl.oz.)
Compressor oil:
ND−OIL 8 or equivalent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2RE−01
AC2674
Condenser
−
AIR CONDITIONING CONDENSER
AC−43
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
HINT:
At the time of installation, refer to the following procedure.
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of
refrigerant.
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
2. REMOVE THESE PARTS:
(a) Hood lock brace
(b) Center brace
3. DISCONNECT DISCHARGE HOSE AND LIQUID TUBE
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate 2 new O −rings with com-
pressor oil to compressor.
4. REMOVE CONDENSER
(a) Remove 2 condenser mounting bolts.
(b) Pull out the condenser between the radiator and the body.
HINT:
If condenser was replaced, add compressor oil to compressor.
Add 40 cc (1.4 fl.oz.)
Compressor oil:
ND−OIL 8 or equivalent
r-=:J__---_______----.-~------=.:-----
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2RU−01
Z17944
Hose ”A”
Hose ”B”
Z19353
Hose Clip
Heater
Radiator
Pipe Paint
Water Hose Upper Upper
Fr RH
Marking Hose ”A”
Hose ”B”
45°
AC−48
−
AIR CONDITIONING WATER VALVE
1375
Author: Date:
1996 LAND CRUISER (RM451U)
WATER VALVE
REMOVAL
1. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all the coolant.
2. DISCONNECT WATER VALVE CONTROL CABLE
3. DISCONNECT WATER HOSES FROM HEATER RA-
DIATOR PIPE AND WATER VALVE
(a) Grip the claws of the hose clip with pliers and slide the clip
along the hose to a place where it does not clamp the
hose to the pipe.
(b) Disconnect the water hoses.
HINT:
ATt the time of installation, refer to the following procedure.
Push the water hose onto the heater radiator pipe as far
as ridge on the pipe.
Install the hose clip in a position, as shown in the illustra-
tion.
4. REMOVE WIRE HARNESS PROTECTOR
5. REMOVE WATER VALVE
Remove the 2 bolts and water valve.
N02485N18180N18181
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14323
AC2S0−02
N14324
N06504
AC−54
−
AIR CONDITIONING REAR BLOWER MOTOR
1381
Author: Date:
1996 LAND CRUISER (RM451U)
REAR BLOWER MOTOR
REMOVAL
1. REMOVE FRONT RH SEAT
2. REMOVE BLOWER MOTOR
(a) Disconnect the connectors from the blower motor and
rear heater relay.
(b) Remove the bolt and rear heater relay.
(c) Remove the 2 screws and side cover.
(d) Remove the bolt and 7 screws, then remove the upper cover with the blower motor.
(e) Remove the 3 screws and the blower motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07268
AT0T0−01
Q07264
Z15453
SST
Z15454
SST
Q07268
−
AUTOMATIC TRANSMISSION SPEEDOMETER DRIVEN GEAR
AT−3
787
Author: Date:
1996 LAND CRUISER (RM451U)
SPEEDOMETER DRIVEN GEAR
ON−VEHICLE REPAIR
1. DISCONNECT SPEEDOMETER CABLE AND RE-
MOVE SPEEDOMETER DRIVEN GEAR
(a) Loosen the serrated collar with pliers. Do not lose the felt
dust protector and washer.
(b) Disconnect the speedometer cable.
(c) Remove the bolt and locking plate. Pry out the speedom-
eter driven gear assembly.
(d) Remove the O−ring from the speedometer driven gear assembly.
(e) Remove the clip and speedometer driven gear from the speedometer driven gear sleeve.
2. REMOVE SPEEDOMETER DRIVEN GEAR OIL SEAL
Using SST, remove the oil seal. SST 09921−00010
3. REINSTALL SPEEDOMETER DRIVEN GEAR OIL SEAL
Using SST, install a new oil seal. SST 09201−10000 (09201 −01080)
Drive in depth: 20 mm (0.79 in.)
4. REINSTALL SPEEDOMETER DRIVEN GEAR AND CONNECT SPEEDOMETER CABLE
(a) Install the clip and speedometer driven gear to the
speedometer driven gear sleeve.
(b) Install a new O−ring to the speedometer driven gear as- sembly.
(c) Install the speedometer driven gear.
(d) Install the locking plate with the bolt.
Torque: 16 N·m (160 kgf·cm, 12 ft·lbf)
(e) Connect the speedometer cable.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07265
AT0T1−01
−
AUTOMATIC TRANSMISSION VEHICLE SPEED SENSOR
AT−5
789
Author: Date:
1996 LAND CRUISER (RM451U)
VEHICLE SPEED SENSOR
ON−VEHICLE REPAIR
1. DISCONNECT NO.2 VEHICLE SPEED SENSOR CON-
NECTOR
2. REMOVE NO.2 VEHICLE SPEED SENSOR
(a) Remove the bolt and No.2 vehicle speed sensor.
(b) Remove the O− ring from the No.2 vehicle speed sensor.
3. REINSTALL NO.2 VEHICLE SPEED SENSOR
(a) Coat a new O −ring with ATF and install it to the No.2 ve-
hicle speed sensor.
(b) Install the No.2 vehicle speed sensor and torque the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
4. RECONNECT NO.2 VEHICLE SPEED SENSOR CON- NECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T3−02
Q07388
AT−6
−
AUTOMATIC TRANSMISSION PARK/NEUTRAL POSITION (PNP) SWITCH
790
Author: Date:
1996 LAND CRUISER (RM451U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. DISCONNECT 2 OIL COOLER PIPES (See page
AT−16 )
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Pry off the lock washer and remove the nut.
(b) Remove the bolt and park/neutral position switch.
4. REINSTALL PARK/NEUTRAL POSITION SWITCH
(a) Install the park/neutral position switch and bolt.
(b) Install a new lock plate and the nut. Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Adjust the park/neutral position switch. (See page DI−131 )
5. RECONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
6. RECONNECT 2 OIL COOLER PIPES (See page AT−17 )
Adjust the shift lever position. (See page DI−131)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07274
AT0T4−01
AT3168
SST
AT1362
Seal Breadth
2 − 3 mm
−
AUTOMATIC TRANSMISSION VALVE BODY ASSEMBLY
AT−7
791
Author: Date:
1996 LAND CRUISER (RM451U)
VALVE BODY ASSEMBLY
ON−VEHICLE REPAIR
1. DRAIN ATF
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
2. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 19 bolts. Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
(b) Install the blade of SST between the transmission case and oil pan, cut off applied sealer and then remove the oil
pan.
SST 09032−00100
NOTICE:
When removing the oil pan, be careful not to damage the oil
pan flange.
HINT:
At the time of installation, after removing all the old FIPG on the
contacting surface of the oil pan and transmission case, apply
new FIPG to the oil pan.(See page AT −1)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
3. WHEN REPLACING 3 SHIFT SOLENOID VALVES
(a) Disconnect the connectors from the solenoid valves.
(b) Remove the 3 solenoid valve mounting bolts. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
(c) Remove the 3 solenoid valves.
HINT:
At the time of installation, replace the O−rings with new ones.
4. REMOVE OIL STRAINER
Remove the 4 bolts, and the oil strainer and gaskets. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Be careful as some fluid will c ome out with the oil strainer.
Bolt length:
Bolt A: 16 mm (0.63 in.)
Bolt B: 20 mm (0.79 in.)
Bolt C: 28 mm (1.10 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010