1996 TOYOTA LAND CRUISER lock

PP303−01
−
PREPARATION ENGINE MECHANICAL
PP−7
1996 LAND CRUISER (RM451U)
SSM (Special Service Materials)
08826−00080Seal Packing Black or equivalent
(FIPG)Over space between cylinder block
and timing chain case
Timing cgain cover
Semi−circular plug
Oil pan
Rear oil seal retainer
08833−00070Adhesive 1324,
THREE BOND 1324 or equivalentPlug tube
08833−00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentTVV
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP30M−01
−
PREPARATION STARTING
PP−25
1996 LAND CRUISER (RM451U)
EQUIPMENT
Dial indicatorCommutator
Magnetic fingerSteel ball
PressMagnetic switch terminal kit
Pull scaleBrush spring
SandpaperCommutator
Torque wrench
V−blockCommutator
Vernier calipersCommutator, Brush
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
PREPARATION SUSPENSION AND AXLE
PP−43
92
Author: Date:
1996 LAND CRUISER (RM451U)
09504−00011Differential Side Bearing
Adjusting Nut WrenchFront differential
Rear differential
09504−22011Differential Side Bearing
ReplacerRear differential
09506−35010Differential Drive Pinion Rear
Bearing ReplacerRear differential
Rear suspension
09509−25011Rear Axle Bearing Lock Nut
WrenchRear axle
09517−36010Rear Axle Shaft Oil Seal
Replacer −Rear axle
09550−10013Replacer Set ”B”Rear differential
Rear suspension
(09553−10010)Differential Side Bearing
Replacer
(09557−10011)Differential Drive Pinion
Front Bearing Replacer
09550−60010Differential Side Bearing
ReplacerRear differential
09556−22010Drive Pinion Front Bearing
RemoverFront differential
Rear differential
09605−60010Steering Knuckle Bearing Cup
Replacer−Front axle
09606−60020Steering Knuckle Bearing RemoverFront axle
09607−60020Front Wheel Adjusting Nut WrenchFront axle
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KO−01
PP−48
−
PREPARATION SUSPENSION AND AXLE
1996 LAND CRUISER (RM451U)
RECOMMENDED TOOLS
09025−00010Small Torque Wrench (30 kgf −cm)Front differential
Rear differential
09031−00030Pin Punch .Front differential
09040−00011Hexagon Wrench Set .Front differential
(09043−20060)Socket Hexagon Wrench 6.
09044−00020Torx Socket E10 .Rear differential
09082−00050TOYOTA Electrical Tester Set.Differential locking system
09905−00012Snap Ring No.1 Expander .Front axle
Front differential
09905−00013Snap Ring Pliers .Front axle
Front differential
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YE−01
PP−50
−
PREPARATION SUSPENSION AND AXLE
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Differential oil
Front w/o Dfferential lock w/ Dfferential lock
Rear
2.80 liters (2.9 US qts, 2.5 lmp. qts)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
3.25 liters (3.4 US qts, 2.9 lmp. qts)
Hypoid gear oil API GL− 5
Above − 18°C (0° F) SAE 90
Below − 18°C (0° F) SAE 80W− 90 or 80W
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YF−02
−
PREPARATION SUSPENSION AND AXLE
PP−51
1996 LAND CRUISER (RM451U)
SSM (Special Service Materials)
08826−00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)Front differential
Rear differential
Differential locking system
08833−00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentFront differential
Rear differential
Differential locking system
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

RS0OZ−02
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
RS−1
1100
Author: Date:
1996 LAND CRUISER (RM451U)
SRS AIRBAG
PRECAUTION
NOTICE:
The LAND CRUISER is equipped with an SRS , which comprises a driver airbag \
and a front pas-
senger airbag. Failure to carry out service operations in the correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serio\
us accident. Further,
if a mistake is made in servicing the SRS, it is possible the SRS may fail to\
operate when re-
quired. Before performing servicing (including removal or installation \
of parts, inspection or
replacement), be sure to read the following items carefully, then follow the correct procedure
described in the repair manual.
Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the mos\
t impor-
tant source of information when troubleshooting. When troubleshooting th\
e SRS, always in-
spect the DTCs before disconnecting the battery.
Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front
passenger airbag assembly, and airbag sensor assembly should be inspected (See pages
RS−9 , RS−23 and RS−34 )
Never use SRS parts from another vehicle. When replacing parts, replace them with \
new parts.
Never disassemble and repair the steering wheel pad, front passenger airbag assembly , or air-
bag sensor assembly in order to reuse it.
If the steering wheel pad, front passenger airbag assembly or airbag sen\
sor assembly have
been dropped, or if there are cracks, dents or other defects in the case, br\
acket or connector,
replace them with new ones.
Use a volt/ohmmeter wi th high impedance (10 k Ω/V minimum) for troubleshooting the system’s
electrical circuits.
Information labels are attached to the periphery of the SRS components. Follow the instruc-
tions on the notices.
After work on the SRS is completed, check the SRS warning light (See pa\
ge DI−240).
If the vehicle is equipped with a mobile communication system, refer to the precaution in the
IN section.
CAUTION:
Work must be started after 90 seconds from the time the ignition switch is t\
urned to the ”LOCK”
position and the negative ( −) terminal cable is disconnected from the battery.
(The SRS is equipped with a back− up power source so that if work is started within 90 seconds
of disconnecting the negative ( −) terminal cable of the battery, the SRS may be deployed.)
When the negative (−) terminal cable is disconnected from the battery, the memory of the clock
and audio system will be canceled. So before starting work, make a record o\
f the contents mem-
orized in the audio memory system. When work is finished, reset the audio syst\
ems as they
were before and adjust the clock. To avoid erasing the memory of each memory system, never
use a back−up power supply from outside the vehicle.
Before repairs, remove the airbag sensor if shocks are likely to be applied to the senso\
r during
repairs.
Do not expose the steering wheel pad, front passenger airbag assembly, or airbag sensor as-
sembly directly to hot air or flames.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R11937
Airbag Sensor
Assembly
Spiral
Cable
Front Passenger
Airbag Assembly
Steering Wheel
Pad
Instrument Panel
Junction Block Junction
Block No. 1
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
RS−3
1996 LAND CRUISER (RM451U)
6. SRS CONNECTORS
No.ItemApplication
(1)Terminal Twin−Lock MechanismConnectors 1, 2, 3, 4, 5, 6, 7
(2)Airbag Activation Prevention MechanismConnectors 2, 3, 4
(3)Electrical Connection Check MechanismConnectors 1
(4)Connector Twin −Lock MechanismConnectors 2, 3, 4
(a) All connectors in the SRS are colored yellow to distin-
guish them from other connectors. Connectors having
special functions and specifically designed for the SRS
are used in the locations shown above to ensure high reli-
ability. These connectors use durable gold −plated termi-
nals.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010