1996 TOYOTA LAND CRUISER coolant temperature

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−135
1996 LAND CRUISER (RM451U)
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to the DLC3, turned the ignition
switch ON and operated the scan tool, there is a problem on the
vehicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
4. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand−held tester only:
By putting the vehicle’s ECM in the check mode, 1 trip detection logic is possible instead of 2\
trip detection
logic and sensitivity to detect open circuits is increased. This makes it easier t\
o detect intermittent problems.
(1) Clear the DTC (See step 3).
(2) Set the check mode (See step 3).
(3) Do a simulation test (See page IN−18).
(4) Check the cnnector connection and terminal (See page IN−28).
(5) Visual check and contact pressure (See page IN−28).
(6) Handle the connector (See page IN−28).
5. ROAD TEST
NOTICE:
Perform the test at normal operating ATF temperature 50 − 80°C (122 − 176° F).
(a) D position test in NORM and PWR pattern positions. Shift into the D position and hold the accelerator pedal constant at the full\
throttle valve opening posi-
tion and check the following:
HINT:
When the 2nd start switch in on, there is no 1 → 2 up−shift and 2 →1 down−shift.
(1) 1 →2, 2 → 3 and 3 → O/D up−shift takes place, and shift point should conform to those shown
in the automatic shift schedule. Conduct a test under both Normal and Powe\
r patterns.
HINT:
There is no O/D up−shift or lock−up when the coolant temperature is below 55 °C (131°F ).
Evaluation:
If there is no 1 → 2 up−shift:
Shift solenoid valve No. 2 is stuck.
1−2 shift valve is stuck.
If there is no 2 → 3 up−shift:
Shift solenoid valve No. 1 is stuck.
2−3 shift valve is stuck.
If there is no 3 → O/D up−shift:
3−4 shift valve is stuck.
If the shift point is defective:
Throttle valve, 1−2 shift valve, 2−3 shift valve, 3−4 shift valve etc., are defective.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KD−02
Q08236
No. 1 Vehicle
Speed Sensor
O/D OFF Indicator Light
MIL
Pattern Select Switch O/D Main Switch
DLC1
Shift Solenoid Valve SL
ECM
Stop Light Switch L4 Position Sensor
Park/Neutral Position Switch No. 2 Vehicle Speed Sensor
Shift Solenoid Valve No. 2
Shift Solenoid Valve No. 1
Engine Coolant Temperature Sensor
Throttle Position Sensor
ATF Temperature Sensor
DLC3
Transfer Neutral
Position Switch
DI−144
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KE−03
Vd762D00115
E4
11
12
13 1415
16
10 12
3
4
567
8
9
10
11
12
123
456
7
1
2
34
56
8910
11
7
8
9
12141516 13
17181920
21
22
23
242526
ECM T
erminals
1
23
4
5
6
7
89
10
11
13 12
15
16
171819202122 14
E5E6E7
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−145
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (T erminal No.)Wiring ColorConditionSTD Voltage (V)
SPD (E7−8) − E1 (E4− 24)L− W − BR− B
Disconnect cruise control connector and IG ON StationaryBelow 1.5
Disconnect cruise control connector and IG ON
Turn one rear wheel slowlyPulse signal is outputBelow 1.5 ↔ 4 − 6
S1 (E4− 10) − E1 (E4− 24)R − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ON9 − 14
1st or 2nd gear9 − 14
3rd or O/D gearBelow 1.5
S2 (E4− 9) − E1 (E4− 24)R−Y − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
2nd or 3rd gear9 − 14
1st or O/D gearBelow 1.5
SL (E4− 8) − E1 (E4− 24)R−L − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
Vehicle driving under lock −up position9 − 14
SP2+ (E6− 2) − SP− (E6− 8)V − V−G
IG OFF Disconnect ECM connector560 − 680 Ω
Engine is runningPulse signal is output
Below 1.5 ↔ 4 − 6
OD1 (E7− 18) − E1 (E4− 24)G−O − BR− BIG ON9 − 14
OD2 (E7− 19) − E1 (E4− 24)P−L − BR− BO/D main switch ON (O/D OFF)Below 3
O/D main switch OFF (O/D ON)9 − 14
OIL (E5− 12) − E2 (E5− 9)R−W − BR− BATF temperature: 110 °C (230° F)Below 1.5
L (E7−17) − E1 (E4− 24)G−W − BR− BIG ON Shift lever L position7.5 − 14
IG ON Shift lever other than L positionBelow 1.5
2 (E7−16) − E1 (E4− 24)O − BR− BIG ON Shift lever 2 position7.5 − 14
IG ON Shift lever other than 2 positionBelow 1.5
R (E7−15) − E1 (E4− 24)R−B − BR− BIG ON Shift lever R position7.5 − 14
IG ON Shift lever other than R positionBelow 1.5
NSW (E7−22) − E1 (E4− 24)B−W − BR− BIG ON Shift lever P or N positionBelow 3
IG ONShift lever other than P and N position9 − 14
STP (E7− 14) − E1 (E4− 24)G−W − BR− BIG ON Brake pedal is depressed7.5 − 14
IG ON Brake pedal is releasedBelow 1.5
THW (E5−4) − E2 (E5− 9)R−W − BR− BIG ON Engine coolant temperature 80 °C (176° F)Below 1.5
IDL (E5− 11) − E2 (E5− 9)G−W − BR− BIG ON Accel. pedal is releasedBelow 1.5
IG ONAccel. pedal is depressed9 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC0GB−01
EC3069
Gasket
Check Valve (V acuum Valve)
EC−6
−
EMISSION CONTROL EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. VISUALLY INSPECT LINES AND CONNECTIONS
Look for loose connections, sharp bends or damage.
2. VISUALLY INSPECT FUEL TANK
Look for deformation, cracks or fuel leakage.
3. VISUALLY INSPECT FUEL TANK CAP
Check if the cap and/or gasket are deformed or damaged.
If necessary, repair or replace the cap.
4. INSPECT TVV OPERATION WITH COLD ENGINE
(a) The engine coolant temperature should be below 45 °C
(113 °F).
(b) Disconnect the EVAP hose from the union pipe.
(c) Start the engine.
(d) Gradually increase the engine speed from idle to 3,000 rpm and check that air suction is not felt at the union pipe.
5. INSPECT OPERATION OF VCV WITH HOT ENGINE
(a) Warm up the engine.
(b) With the engine idling, check that air suction is not felt at union pipe.
(c) Gradually increase the engine speed to 3,000 rpm and check that there is air suction at the union pipe.
(d) Reconnect the EVAP hose to the union pipe.
If no problem is found with this inspection, system is normal;
otherwise inspect each part.
6. REMOVE CHARCOAL CANISTER WITH BRACKET
7. REMOVE CHARCOAL CANISTER FROM BRACKET
8. REMOVE CAP FROM CHARCOAL CANISTER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC0JT−01
−
EMISSION CONTROL EXHAUST GAS RECIRCULATION (EGR) SYSTEM
EC−11
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT AND CLEAN FILTER IN EGR V ACUUM MOD-
ULATOR
(a) Remove the cap and filter.
(b) Check the filter for contamination or damage.
(c) Using compressed air, clean the filter.
(d) Reinstall the filter and cap.
HINT:
Install the filter with the coarser surface facing the atmospheric
side (outward).
2. INSTALL VACUUM GAUGE
Using a 3 −way connector, connect a vacuum gauge to the hose
between the EGR valve and EGR vacuum modulator.
3. INSPECT SEATING OF EGR VALVE
Start the engine and check that the engine starts and runs at
idle.
4. CONNECT TOYOTA HAND− HELD TESTER OR OBD II
SCAN TOOL (See page EM−10)
5. INSPECT VSV OPERATION WITH COLD ENGINE
(a) The engine coolant temperature should be below 47 °C
(117 °F).
(b) Check that the vacuum gauge indicates zero at 2,500 rpm.
(c) Check that the EGR pipe is not hot.
6. INSPECT OPERATION OF VSV AND EGR VACUUM
MODULATOR WITH HOT ENGINE
(a) Warm up the engine to above 53° C (127°F).
(b) Check that the vacuum gauge indicates low vacuum at 2,500 rpm.
(c) Disconnect the vacuum hose port R of the EGR vacuum modulator and connect port R directly to the air intake
chamber with another hose.
(d) Check that the vacuum gauge indicates high vacuum at 2,500 rpm.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA02R−04
MA−4
−
MAINTENANCE UNDER HOOD
44
Author: Date:
1996 LAND CRUISER (RM451U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTICE
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performe\
d.
Periodic maintenance service must be performed according to whichever interval in\
the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time inter\
val (months).
Maintenance service after the last period should be performed at the same interval \
as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and incre\
ase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL Check that the coolant level is between the FULL and LOW lines on the se\
e −through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leave\
s, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upp\
er and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE FLUID LEVELS
Check that the brake fluid level is near the upper level line on the see\
−through reservoir.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temp\
erature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking and foot brake applied, shift the sel\
ector into all positions from the P to L, and then shift into the P.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re −insert the dipstick fully and check that
the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C (158 − 176° F)).
HINT:
Wait about 30 minutes before checking the fluid level after extended driving\
at high speeds in hot weather,
driving in heavy traffic or with a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is\
noticed, have the cause located
and corrected.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YT−01
PP−66
−
PREPARATION BODY ELECTRICAL
1996 LAND CRUISER (RM451U)
EQUIPMENT
Bulb (3.4 W)Fuel sender gauge
Seat belt warning relay
Bulb (21 W)Turn signal flasher relay
Clip removerFor removing cowl louver
Dry cell batteryFuel sender gauge
Masking tapeRear window defogger wire
Oil bathEngine oil level warning switch
Test lead
ThermometerEngine coolant temperature sender gauge
Engine oil level warning switch
Tin foilRear window defogger wire
Torque wrench
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KK−01
−
PREPARATION BODY ELECTRICAL
PP−67
1996 LAND CRUISER (RM451U)
SSM (Special Service Materials)
08833−00070Adhesive 1324,
THREE BOND 1324 or equivalentPower seat housing set nut
Power seat slide and vertical motor set
screw
08833−00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentLow oil pressure warning switch
Engine coolant temperature sender
gauge
08888−88888DuPont Paste No. 4817 or
equivalentRear window defogger
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010