1996 TOYOTA LAND CRUISER torque

SF1EW−04
−
SFI THROTTLE BODY
SF−45
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT NO.2 PCV HOSE
3. DISCONNECT AIR CLEANER HOSE
4. DISCONNECT CONTROL CABLES FROM THROTTLE
BODY
5. DISCONNECT THROTTLE POSITION SENSOR CON-
NECTOR
6. DISCONNECT IDLE AIR CONTROL VALVE CONNEC- TOR
7. REMOVE THROTTLE BODY
(a) Disconnect the EVAP hose.
(b) Disconnect the 3 vacuum hoses.
(c) Disconnect the No.2 water bypass hose.
(d) Remove the 4 bolts, and disconnect the throttle body from
the air intake chamber.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(e) Remove the throttle body gasket.
HINT:
At the time of installation, plaese refer to the following items.
install a new gasket on the air intake chamber.
(f) Disconnect the No.1 water bypass hose from the throttle
body, and remove the throttle body.
(g) Disconnect the No.2 water bypass hose from the throttle
body.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1F8−01
SF−58
−
SFI FUEL PUMP RESISTOR
686
Author: Date:
1996 LAND CRUISER (RM451U)
FUEL PUMP RESISTOR
INSPECTION
1. REMOVE FUEL PUMP RESISTOR
(a) Disconnect the fuel pump resistor connector.
(b) Remove the bolt and fuel pump resistor.
2. INSPECT FUEL PUMP RESISTOR
Using an ohmmeter, measure the resistance between the ter-
minals.
Resistance: 0.70 − 0.76 Ω at 20°C (68°F)
If there is no continuity, replace the resistor.
3. REINSTALL FUEL PUMP RESISTOR Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0PO−09
Z02917
Ohmmeter
TEMPERATURE °C (° F)
RESISTANCE kΩ
Acceptable
−
SFI ENGINE COOLANT TEMPERATURE (ECT) SENSOR
SF−61
689
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE COOLANT
TEMPERATURE (ECT) SENSOR
INSPECTION
1. DRAIN ENGINE COOLANT
2. REMOVE ECT SENSOR
(a) Disconnect the ECT sensor connector.
(b) Using a 19 mm deep socket wrench, remove the ECT
sensor and gasket.
3. INSPECT ECT SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals. Resistance: Refer to the chart graph
If the resistance is not as specified, replace the ECT sensor.
4. REINSTALL ECT SENSOR
(a) Using a 19 mm deep socket wrench, install the ECT sen- sor and gasket.
Torque: 24.5 N·m (250 kgf·cm, 17.5 ft·lbf)
(b) Connect the ECT sensor connector.
5. REFILL ENGINE COOLANT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1FB−01
P01630
Ohmmeter
SF−62
−
SFI KNOCK SENSOR
690
Author: Date:
1996 LAND CRUISER (RM451U)
KNOCK SENSOR
INSPECTION
1. REMOVE KNOCK SENSOR
(a) Disconnect the knock sensor connector.
(b) Using SST, remove the knock sensor.
SST 09816−30010
2. INSPECT KNOCK SENSOR
Using an ohmmeter, check that there is no continuity between
the terminal and body.
If there is continuity, replace the sensor.
3. REINSTALL KNOCK SENSOR
(a) Using SST, install the knock sensor. SST 09816−30010
Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
(b) Connect the knock sensor connector.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1FA−01
FI6320
Ohmmeter
Oil
−
SFI EXHAUST GAS RECIRCULATION (EGR) GAS
TEMPERATURE SENSORSF−63
691
Author: Date:
1996 LAND CRUISER (RM451U)
EXHAUST GAS RECIRCULATION
(EGR) GAS TEMPERATURE
SENSOR
INSPECTION
1. REMOVE EGR GAS TEMPERATURE SENSOR
2. INSPECT EGR GAS TEMPERATURE SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals.
TemperatureResistance
50 °C (122° F)64 − 97 kΩ
100°C (212° F)11 − 16 kΩ
150 °C (302° F)2 − 4 kΩ
If the resistance is not as specified, replace the sensor.
3. REINSTALL EGR GAS TEMPERATURE SENSOR
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16D−02
R09496
SST
SR−16
−
STEERING TILT STEERING COLUMN
1996 LAND CRUISER (RM451U)
REASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. COAT WITH MOLYBDENUM DISULFIDE LITHIUM BASE GREASE (See page SR−9 )
2. INSTALL MAIN SHAFT ASSEMBLY
(a) Install a new bearing, bearing thrust collar and compres- sion spring to the shaft assembly.
(b) Install the shaft assembly into the column upper tube.
(c) Using SST, compress the compression spring. SST 09950−40010 (09957 −04010, 09958−04010)
NOTICE:
Do not bend the universal joint of the main shaft more than
20 °.
(d) Using snap ring pliers, install a new snap ring.
3. INSTALL TURN SIGNAL BRACKET
Torque the 2 bolts. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
4. SELECT TILT NO.2 BOLTS
Select the bolt with plain thread end when the column upper
tube mark is 2, and the bolt with the hollow −tipped thread end
when the mark is 1.
NOTICE:
Select the bolt type to match each number marked in the
squares on the upper tube.
5. INSTALL COLUMN UPPER TUBE WITH MAIN SHAFT ASSEMBLY
(a) Install the collar to the shaft assembly.
(b) Install a new snap ring.
(c) Install the upper tube with the shaft assembly into the col-
umn lower tube.
(d) Using a plastic hammer, drive in the 2 tilt No.2 bolts.
6. INSTALL TILT LEVER LOCK SHAFT, TILT LEVER AS- SEMBLY, TILT SUB LEVER AND TILT LEVER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR3128
Mark
”A”
”A”
−
STEERING TILT STEERING COLUMN
SR−17
1996 LAND CRUISER (RM451U)
7. INSTALL 2 TILT PAWLS
(a) Coat the collar with molybdenum disulfide lithium base
grease and install it to the tilt pawl.
(b) Install the pawl.
HINT:
Install the pawl pin into the long hole of the tilt lever/ tilt sub lever.
(c) Install the bolt through the pawls and tilt lever assembly.
(d) Temporarily install the 2 washers and nut.
(e) Torque the tilt lever assembly set bolt.
Torque: 2.9 N·m (30 kgf·cm, 26 in.·lbf)
8. ENGAGE AND ADJUST 2 TILT PAWLS
(a) Engage the tilt sub lever side pawl to the center of the ratchet.
(b) While turning the tilt lever side tilt pawl collar, completely engage the tilt lever side pawl to the ratchet.
(c) Torque the nut.
Torque: 5.9 N·m (60 kgf·cm, 52 in.·lbf)
9. SELECT AND INSTALL 2 TILT PAWL STOPPERS
(a) With the tilt pawl and ratchet engaged, install the stopper.
(b) Check that the alignment marks on the stopper and pawl
align when the stopper is rotated to the pawl side.
(c) If the alignment marks do not align, select stopper accord-
ing to the following table.
Tilt lever sideTilt sub lever sideDimension ”A”
mm (in.)
1A12.65 − 12.75
(0.4980 − 0.5020)
2B12.55 − 12.65
(0.4941 − 0.4980)
3C12.45 − 12.55
(0.4902 − 0.4941)
4D12.35 − 12.45
(0.4862 − 0.4902)
5E12.25 − 12.35
(0.4823 − 0.4862)
(d) After selecting the stoppers, check that on both sides the
pawl and ratchet are fully engaged.
10. INSTALL 2 TILT LEVER RETAINERS
(a) Install a new E−ring.
(b) Torque the nut. Torque: 15 N·m (150 kgf·cm, 11 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR−18
−
STEERING TILT STEERING COLUMN
1996 LAND CRUISER (RM451U)
11. INSTALL 3 TENSION SPRINGS
12. INSTALL COMPRESSION SPRING
(a) Install the 2 bushings to the spring.
(b) Torque the bolt.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)
13. INSTALL COLUMN UPPER BRACKET AND COLUMN UPPER CLAMP
Tighten 2 new tapered −head bolts until the bolt head brakes off.
14. INSTALL WIRING HARNESS CLAMP
Tighten the bolt.
15. INSTALL COLUMN HOLE SHIELD, COLUMN HOLE COVER AND LOWER DUST SEAL
(a) Install the hole shield to the hole cover.
(b) Install the dust seal to the hole cover.
(c) Torque 2 bolts. Torque: 5.9 N·m (60 kgf·cm, 52 in.·lbf)
16. CONNECT UNIVERSAL JOINT
(a) Align the matchmarks on the intermediate No.2 shaft and
universal joint then torque the bolt.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
(b) Align the matchmarks on the universal joint and the main shaft then torque the bolt.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
17. CHECK TILT STEERING COLUMN OPERATION
(a) Check that there is no axial play at the end of the main
shaft.
(b) With the main shaft in the neutral position, raise the tilt le- ver and check that the main shaft rises to the uppermost
position.
(c) Lower the main shaft, and check that it locks in the lower-
most position.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010