1996 TOYOTA LAND CRUISER Ect

BE1MS−01
BE−94
−
BODY ELECTRICAL ANTENNA
1232
Author: Date:
1996 LAND CRUISER (RM451U)
ANTENNA
INSPECTION
1. w/ MOTOR ANTENNA:
INSPECT ANTENNA SWITCH
Except RADIO−LINKED TYPE
ConditionTester connectionSpecified condition
UP Button
Position Free2 − 5Continuity
UP Button
Position Pushed in4 − 5Continuity
DOWN Button
Position Free2 − 3Continuity
DOWN Button
Position Pushed in3 − 4Continuity
Illumination circuit1 − 6Continuity
If continuity is not as specified, replace the switch.
2. INSPECT ANTENNA MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2, and check that
the motor turns (moves upward.)
(b) Then, reverse the polarity, check that the motor turns the
opposite way (moves downward.)
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MT−01
−
BODY ELECTRICAL CLOCK
BE−95
1233
Author: Date:
1996 LAND CRUISER (RM451U)
CLOCK
TROUBLESHOOTING
HINT:
Troubleshoot the lock according to the table below.
Clock will not operate1
Clock loses or gains time2
1.5 seconds/day
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−96
−
BODY ELECTRICAL CLOCK
1234
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37G−01
−
BODY SRS AIRBAG
BO−3
1237
Author: Date:
1996 LAND CRUISER (RM451U)
SRS AIRBAG
PRECAUTION
The LAND CRUISER is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in th\
e correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in\
-
cluding removal or installation of parts, inspection or replacement), be sure t\
o read the precautionary notices
in the RS section.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37H−01
BO−4
−
BODY FRONT BUMPER
1238
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT BUMPER
COMPONENTS
CAUTION:
The side rail extensions are necessary for normal function-
ing of the SRS airbag, so make sure that they are correctly
installed.When replacing the bumper, always inspect the
side rail extensions. If they are deformed or cracked, re-
place them. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO5235
Centering BoltBolt
with W asher
BO37J−01
BO−6
−
BODY HOOD
1240
Author: Date:
1996 LAND CRUISER (RM451U)
HOOD
ADJUSTMENT
HINT:
Since the centering bolt is used as the hood hinge and lock set
bolt, the hood and lock cannot be adjusted with it on. Substitute
the bolt with washer for the centering bolt.
1. ADJUST HOOD IN FORW ARD/REARWARD AND LEFT
/RIGHT DIRECTIONS
Adjust the hood by loosening the hood side hinge bolts. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
2. ADJUST FRONT EDGE OF HOOD IN VERTICAL DIRECTIONS
(a) Loosen the lock nut.
(b) Adjust the hood by turning the cushions.
3. ADJUST REAR EDGE OF HOOD IN VERTICAL DIREC-
TIONS
Adjust the hood by loosening the body side hinge bolts.
4. ADJUST HOOD LOCK
Adjust the hood lock by loosening the mounting bolts. Torque: 8.0 N·m (80 kgf·cm, 69 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37O−01
−
BODY FRONT DOOR
BO−11
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE GLASS CHANNEL WITH SCREWDRIVER
OR LIKE OBJECT
2. A P P LY S O A P Y WAT E R TO I N S I D E O F W E AT H- ERSTRIP
3. INSTALL CHANNEL BY TAPPING IT WITH PLASTIC HAMMER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37M−01
BO2556
BO−12
−
BODY FRONT DOOR
1996 LAND CRUISER (RM451U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts. SST 09812−00010
Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL DIRECTIONS
Loosen the door side hinge bolts to adjust. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Loosen the striker mounting screws to adjust.
(c) Using a plastic hammer, tap the striker to adjust it.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010