1996 TOYOTA LAND CRUISER Ect

BO2455
Cotton TapePanel
Cover
BO−16
−
BODY REAR DOOR
1996 LAND CRUISER (RM451U)
NOTICE:
Do not block the clip sealing with the tape.
11. REMOVE DOOR SPEAKER
12. REMOVE LINK PROTECTOR
13. REMOVE LOCKING LINK AND DOOR OPENING LINK
14. REMOVE DOOR GLASS RUN
15. REMOVE REAR LOWER FRAME
16. REMOVE QUARTER WINDOW GLASS WITH WEATH-
ERSTRIP
17. REMOVE DOOR GLASS
18. REMOVE WINDOW REGULATOR Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face and gears of the regulator.
NOTICE:
Do not apply grease to the spring.
19. REMOVE DOOR LOCK
HINT:
At the time of reassembly, apply adhesive to the 3 screws. Part No.08833 −00070, THREE BOND 1324 or equiva-
lent
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face of the door lock.
20. REMOVE OUTSIDE HANDLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37T−01
−
BODY REAR DOOR
BO−17
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE GLASS CHANNEL WITH SCREWDRIVER
OR LIKE OBJECT
2. A P P LY S O A P Y WAT E R TO I N S I D E O F W E AT H- ERSTRIP
3. INSTALL CHANNEL BY TAPPING IT WITH PLASTIC HAMMER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37R−01
BO−18
−
BODY REAR DOOR
1996 LAND CRUISER (RM451U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Adjust the door by loosening the body side hinge bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
2. ADJUST DOOR IN LEFT /RIGHT AND VERTICAL DIRECTIONS
Adjust the door by loosening the door side hinge bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Loosen the striker mounting screws to adjust.
(c) Using a plastic hammer, tap the striker to adjust it.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37X−01
−
BODY BACK DOOR
BO−23
1996 LAND CRUISER (RM451U)
ADJUSTMENT
1. ADJUST UPPER BACK DOOR
(a) Adjust the door in forward/rearward and left/right direc-
tions.
Adjust the door by loosening the door side hinge bolts.
(b) Adjust the door in left/right and vertical directions. Adjust the door by loosening the body side hinge bolts.
(c) Adjust the door lock striker. (1) Check that the door fit and door lock linkage are ad-
justed correctly.
(2) Adjust the striker position by slightly loosening the striker mounting screws, and hitting the striker with
a hammer. Tighten the striker mounting screw
again.
2. ADJUST LOWER BACK DOOR
(a) Adjust the door in forward/rearward and left/right direc- tions.
Adjust the door by loosening the door side hinge bolts.
(b) Adjust the door in left/right and vertical directions. Adjust the door by loosening the body side hinge bolts.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−24
−
BODY BACK DOOR
1996 LAND CRUISER (RM451U)
(c) Adjust the door lock striker.
(1) Check that the door fit and door lock linkages areadjusted correctly.
(2) Adjust the striker position by slightly loosening the striker mounting screws, and hitting the striker with
a hammer.
(3) Tighten the striker mounting screws again.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO382−01
BO−28
−
BODY FRONT WIPER AND WASHER
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE WIPER ARMS
2. REMOVE COWL LOUVER
3. REMOVE WIPER MOTOR AND WIPER LINK
(a) Disconnect the connector, then unfasten 4 bolts and wip-
er motor.
(b) Remove the wiper link.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48K−01
BE3367
2 − 2.5 mm
(0.079 − 0.098 in.)
0.7 − 0.75 mm
(0.028 − 0.030 in.)
−
BODY FRONT WIPER AND WASHER
BO−29
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT FRONT WASHER NOZZLE
(a) While operating the washer, check that both the point
where the washer fluid from the upper nozzles hits the
windshield, and the upsurge area, are within the range in-
dicated by the arrow.
AApprox. 460 mm (18.1 in.)
BApprox. 300 mm (11.8 in.)
CApprox. 250 mm (9.84 in.)
DApprox. 400 mm (15.7 in.)
EApprox. 410 mm (16.1 in.)
FApprox. 220 mm (8.66 in.)
GApprox. 60 mm (2.36 in.)
(b) Check if the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the
area of the glass which is wiped by the wiper blades).
2. ADJUST FRONT WASHER NOZZLE
Using a tool like that shown in the illustration, change the direc-
tion of the nozzle hole to adjust the point where washer fluid
strikes the windshield.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO385−01
−
BODY REAR WIPER AND WASHER
BO−31
1265
Author: Date:
1996 LAND CRUISER (RM451U)
REAR WIPER AND WASHER
REMOVAL
1. REMOVE PULL HANDLE AND PULL HANDLE BEZEL
2. REMOVE BACK DOOR TRIM
(a) Insert a screwdriver between the retainers and door trim
to pry it loose.
HINT:
Tape the screwdriver tip before use.
(b) Remove the back door trim.
3. REMOVE WIPER ARM, MOTOR AND REAR WIPER CONTROL RELAY
(a) Open the cap.
(b) Remove the nut and wiper arm.
(c) Remove the 5 bolts and motor, then disconnect the con- nector.
(d) Remove the bolts and rear wiper control relay,then dis- connect the connector.
4. ADJUST REAR WASHER NOZZLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010