1996 TOYOTA LAND CRUISER Bolt

SA2405
SST
R13141
SST
SA2402
SST
Z00641
SST
R13142
Matchmarks
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−31
1996 LAND CRUISER (RM451U)
11. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, unstake the nut.
(b) Using SST to hold the flange, remove the nut and plate
washer.
SST 09330−00021
(c) Using SST, remove the companion flange. SST 09950 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
12. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal from the dif ferential carrier.
SST 09308−10010
(b) Remove the oil slinger.
13. REMOVE REAR BEARING
Using SST, remove the rear bearing from the drive pinion. SST 09556−22010
14. REMOVE DIFFERENTIAL CASE
(a) Place matchmarks on the bearing cap and dif ferential car-
rier.
(b) Remove the 2 adjusting nut locks.
(c) Remove the 4 bolts and 2 bearing caps.
(d) w/o Differential lock: Remove the 2 adjusting nuts.
(e) w/o Differential lock: Remove the differential case with the side bearing outer
races from the carrier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z15178
Matchmarks
SA2464
W03472
SST
RA0997
FA2046
Matchmarks
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−33
1996 LAND CRUISER (RM451U)
18. REMOVE RING GEAR
(a) Using a screwdriver and hammer, unstake the lock plate.
(b) Place matchmarks on the ring gear and differential case.
(c) Remove the ring gear 10 set bolts and 5 lock plates.
(d) Using a plastic hammer, tap on the ring gear to separate
it from the differential case.
19. CHECK DIFFERENTIAL CASE RUNOUT
(a) Install the differential case in the differential carrier and tighten the adjusting nut just to where there is no play in
the bearing.
(b) Using a dial indicator, measure the differential case run- out.
Maximum case runout: 0.07 mm (0.0028 in.)
(c) Remove the differential case.
20. REMOVE SIDE BEARING FROM DIFFERENTIAL CASE
Using SST, pull the side bearing from the differential case. SST 09950 −40010 (09951 −04010, 09952 −04020,
09953 −04020, 09954 −04010, 09955 −04010,
09957 −04010, 09958 −04010),
09950 −60010 (09951 −00480)
HINT:
Fix the claws of SST to the notches in the differential case.
21. w/o DIFFERENTIAL LOCK: DISASSEMBLE DIFFERENTIAL CASE
(a) Using a pin punch and hammer, remove the straight pin.
(b) Remove these parts from the differential case:
Pinion shaft
2 Pinion gears
2 Pinion gear thrust washers
2 Side gears
2 Side gear thrust washers
22. w/ DIFFERENTIAL LOCK: DISASSEMBLE DIFFERENTIAL CASE
(a) Place matchmarks on the LH and RH cases.
(b) Remove the 8 bolts uniformly, a little at a time.
(c) Using a plastic hammer, separate the LH and RH cases.
(d) Remove these parts from the RH differential case:
2 Side gears
2 Side gear thrust washers
Spider
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1987
SA1978
SA1976
FA2037
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−37
1996 LAND CRUISER (RM451U)
3. w/ DIFFERENTIAL LOCK:
MEASURE CLEARANCE OF SHIFT FORK AND
SLEEVE
Using a feeler gauge, measure the clearance between the shift
fork and sleeve. Clearance:
0.15 − 0.35 mm (0.006 − 0.014 in.)
4. w/ DIFFERENTIAL LOCK: ASSEMBLE DIFFERENTIAL CASE
(a) Apply all of the sliding and rotating sufaces with gear oil.
(b) Install the side gear thrust washer to the side gear.
(c) Install the side gear to the RH case.
(d) Install the 4 pinion gears and pinion gear thrust washers to the spider.
(e) Install the pinion gear with the spider to the RH case.
(f) Using a dial indicator, holding the side gear and spider and measure the side gear backlash.
Backlash: 0.05 − 0.20 mm (0.0020 − 0.0079 in.)
HINT:
Measure at all 4 locations.
Measure the backlash at the RH case and at the LH case.
If the backlash is not within the specification, install a thrust
washer of a different thickness. Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
0.9 (0.035)1.2 (0.047)
1.0 (0.039)1.3 (0.051)
1.1 (0.043)−
(g) Install the side gear and side gear thrust washer to the RH
case.
(h) Install the pinion gears and spider to the RH case.
(i) Install the side gear and side gear thrust washer to the RH
case.
(j) Align the matchmarks on the LH and RH cases.
(k) Torque the 8 bolts uniformly, a little at a time. Torque: 47 N·m (480 kgf·cm, 35 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2160
Boiling Water
SA2178
SA2182
SA−38
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
5. INSTALL SIDE BEARINGS
w/o Differential lock:
Using SST and a press, install the 2 side bearings on the
differential case.
SST 09950−60010 (09951 −00480)
w/ Differential lock:
Using SST and a press, install the 2 side bearings on the
differential case.
SST 09223−15020, 09950 −60010 (09951−00480)
6. INSTALL RING GEAR ON DIFFERENTIAL CASE
(a) Clean the contact surfaces of the differential case and ring gear.
(b) Heat the ring gear to about 100° C (212°F) in boiling wa-
ter.
(c) Carefully remove the ring gear from the water.
(d) After the moisture on the ring gear has completely evapo-
rated, quickly install the ring gear to the differential case.
(e) Align the matchmarks on the ring gear and differential
case.
(f) Temporarily install new 5 lock plates and 10 set bolts.
NOTICE:
The ring gear set bolts should not tighten until the ring gear
has cooled sufficiently.
(g) After the ring gear cools down enough, tighten the set bolts uniformly and a little at a time.
Torque: 97 N·m (985 kgf·cm, 71 ft·lbf)
(h) Using a drift punch and hammer, stake the lock plates.
HINT:
Stake one claw flush with the flat surface of the bolt. For the
claw contacting the protruding portion of the bolt, stake only the
half on the tightening side.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06898
SA2458
Matchmarks
SA2467SST
Z10281SST
SA2308
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−41
1996 LAND CRUISER (RM451U)
14. w/o DIFFERENTIAL LOCK:
INSTALL ADJUSTING NUTS
Install the adjusting nuts on the carrier , making sure the nuts are
threaded properly.
15. INSTALL BEARING CAPS
Align the matchmarks on the cap and carrier. Screw in the 2
bearing cap bolts 2 or 3 turns and press down the bearing cap
by hand.
HINT:
If the bearing cap does not fit tightly on the carrier , the adjusting
nuts are not threaded properly.
Reinstall the adjusting nuts if necessary.
16. ADJUST SIDE BEARING PRELOAD
(a) Torque the 4 bearing cap bolts to the specified torque, and loosen them to the point where the adjusting nuts can
be turned by SST.
SST 09504−00011
Torque: 78 N·m (800 kgf·cm, 58 ft·lbf)
(b) Fully tighten the 4 bearing cap bolts by hand.
(c) Using the SST, torque the adjusting nut on the ring gear side until the ring has a backlash of about 0.2 mm (0.008
in.).
(d) With turning the ring gear, use the SST to fully tighten the adjusting nut on the drive pinion side. After the bearings
are settled, loosen the adjusting nut on the drive pinion
side.
(e) Place a dial indicator on the top of the adjusting nut on the ring gear side.
(f) Adjust the side bearing for zero preload by tightening the
other adjusting nut until the pointer on the indicator be-
gins to move.
(g) Torque the adjusting nut 1 − 1.5 notches from the zero preload position.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2443SST
SA2403
SA2463
FA2013
Proper ContactHeel Contact
Face Contact
Select an adjusting washer that will bring the drive
pinion closer to the ring gear.
Select an adjusting washer that will shift the drive
pinion away from the ring gear.
Toe Contact
Flank Contact
SA−42
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(h) Using a dial indicator, adjust the ring gear backlash until
it is within the specification.
Backlash: 0.13 − 0.18 mm (0.0051 − 0.0071 in.)
HINT:
The backlash is adjusted by turning the left and right adjusting
nuts equal amounts. For example, loosen the nut on the left
side one notch and torque the nut on the right side one notch.
(i) Torque the 4 bearing cap bolts. Torque: 78 N·m (800 kgf·cm, 58 ft·lbf)
(j) Recheck the ring gear backlash. Backlash: 0.13 −0.18 mm (0.0051 −0.0071 in.)
(k) Using a torque wrench, measure the preload. Total preload (at starting):
Drive pinion preload plus
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
17. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
(a) Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead.
(b) Hold the companion flange firmly and rotate the ring gear
in both directions.
(c) Inspect the tooth pattern.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2390
SST
SA2403
SA2471
SA−44
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(b) Install the plate washer and a new nut.
HINT:
Coat the threads of a new nut with gear oil.
(c) Using SST to hold the flange, tighten the nut.
SST 09330−00021
Torque: 196 N·m (2,000 kgf·cm, 145 ft·lbf)
24. ADJUST DRIVE PINION PRELOAD
Using a torque wrench, measure the preload of the backlash
between the drive pinion and ring gear. Preload (at starting):
New bearing:
0.9 − 1.6 N·m (10 − 16 kgf·cm, 8.7 − 13.9 in.·lbf)
Reused bearing:
0.5 − 0.8 N·m (5 − 8 kgf·cm, 4.3 − 6.9 in.·lbf)
If the preload is greater than the specification, replace the bear-
ing spacer.
If the preload is less than the specification, retighten the nut a
little at a time with a torque of 13 N·m (130 kgf·cm, 9 ft·lbf) until
the specified preload is reached. Maximum torque: 343 N·m (3,500 kgf·cm, 253 ft·lbf)
If the maximum torque is exceeded while retightening the nut,
replace the bearing spacer and repeat the preload procedure.
Do not back off the pinion nut to reduce the preload.
25. RECHECK RING GEAR BACKLASH
26. RECHECK TOOTH CONTACT BETWEEN RING GEAR
AND DRIVE PINION
27. CHECK RUNOUT OF COMPANION FLANGE
28. STAKE DRIVE PINION NUT
29. INSTALL ADJUSTING NUT LOCKS
(a) Install 2 new nut locks on the bearing caps. Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(b) After tightening bolts, bend the nut locks.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2417
Holes
Groore
Z15179
FIPG Width Approx.
1 − 2 mm (0.04 − 0.08 in.)
Z10101
Adhesive
SA2205
SA1979Lock
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
SA−45
1996 LAND CRUISER (RM451U)
30. w/ DIFFERENTIAL LOCK:
INSTALL SHIFT FORK SHAFT
(a) Apply MP grease onto the outer circuit of the fork shaft.
(b) Install the fork shaft to match the hole of the shift fork and
that of the shift fork shaft.
(c) Remove any FIPG material and be careful not to drop oil on the contacting surface of the differential carrier and
shaft retainer.
(d) Apply FIPG to the carrier, as shown. FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
HINT:
Install the shaft retainer within 10 minutes after applying FIPG.
(e) Clean the threads of the bolts and retainer bolts holes with
toluene or trichlorethylene.
(f) Apply adhesive to 2 or 3 threads of the mount bolt end. Adhesive: Part No. 08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(g) Tighten the shaft retainer with the 2 bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(h) Using a pin punch and hummer, install the slotted spring pin to the shift fork.
(i) Shift the fork deeply and keep the differential lock condi- tion.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010