1996 TOYOTA LAND CRUISER lock

AT3417
OK if hot
Add if hot
Q07273
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−137
1996 LAND CRUISER (RM451U)
(e) P position test.
Stop the vehicle on a grade (more than 5 °) and after shifting into the P position, release the parking
brake. Then, check to see that the parking lock pawl holds the vehicle i\
n place.
6. BASIC INSPECTION
(a) Check the fluid level.
HINT:
Drive the vehicle so that the engine and transmission are
at normal operating temperature.
Fluid temp.: 70 − 80°C (158 − 176° F)
Only use the COOL range on the dipstick as a rough refer-
ence when the ATF is replaced or the engine does not
run.
(1) Park the vehicle on a level surface and set the park-
ing brake.
(2) With the engine idling and the brake pedal de- pressed, shift the shift lever into all positions from P
to L position and return to P position.
(3) Pull out the dipstick and wipe it clean.
(4) Push it back fully into the pipe.
(5) Pull it out and check that the fluid level is in the HOT range.
If the level is at the low side, add new fluid. Fluid type: ATF DEXRON ®II
NOTICE:
Do not overfill.
(b) Check the fluid condition. If the fluid smells burnt or is black, replace it.
(c) Replace the ATF. (1) Remove the drain plug and drain the ATF.
(2) Reinstall the drain plug securely.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KB−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−143
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed for that code i\
n the table below and pro-
ceed to the page given.
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P0500
( DI−153 )Vehicle Speed Sensor Malfunc-
tion
(No. 1 Vehicle Speed Sensor)Open or short in No. 1 vehicle speed sensor circuit
 No. 1 vehicle speed sensor
 ECM

P0710
( DI−154 )Transmission Fluid Temperature
Sensor Malfunction
(ATF Temperature Sensor) Open or short in ATF temperature sensor circuit
 ATF temperature sensor
 ECM

P0750
( DI−156 )Shift Solenoid A Malfunction
(Shift Solenoid Valve No. 1)Shift solenoid valve No. 1 is stuck open or closed
 Valve body is blocked up or stuck
P0753
( DI−157 )Shift Solenoid A Electrical
Malfunction
(Shift Solenoid Valve No. 1)Open or short in shift solenoid valve No. 1 circuit
 Shift solenoid valve No. 1
 ECM

P0755
( DI−156 )Shift Solenoid B Malfunction
(Shift Solenoid Valve No. 2)Shift solenoid valve No. 2 is stuck open or closed
 Valve body is blocked up or stuck
P0758
( DI−157 )Shift Solenoid B Electrical
Malfunction
(Shift Solenoid Valve No. 2)Open or short in shift solenoid valve No. 2 circuit
 Shift solenoid valve No. 2
 ECM

P0770
( DI−161 )Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)Shift solenoid valve SL is stuck open or closed
 Valve body is blocked up or stuck
 Lock− up clutch

P0773
( DI−163 )Shift Solenoid E Electrical
Malfunction
(Shift Solenoid Valve SL)Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM

P1700
( DI−166 ) Speed Sensor No. 2 Circuit
Malfunction
(No. 2 Vehicle Speed Sensor)Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM

P1780
( DI−169 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*:  ...MIL light up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KE−03
Vd762D00115
E4
11
12
13 1415
16
10 12
3
4
567
8
9
10
11
12
123
456
7
1
2
34
56
8910
11
7
8
9
12141516 13
17181920
21
22
23
242526
ECM T
erminals
1
23
4
5
6
7
89
10
11
13 12
15
16
171819202122 14
E5E6E7
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−145
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (T erminal No.)Wiring ColorConditionSTD Voltage (V)
SPD (E7−8) − E1 (E4− 24)L− W − BR− B
Disconnect cruise control connector and IG ON StationaryBelow 1.5
Disconnect cruise control connector and IG ON
Turn one rear wheel slowlyPulse signal is outputBelow 1.5 ↔ 4 − 6
S1 (E4− 10) − E1 (E4− 24)R − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ON9 − 14
1st or 2nd gear9 − 14
3rd or O/D gearBelow 1.5
S2 (E4− 9) − E1 (E4− 24)R−Y − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
2nd or 3rd gear9 − 14
1st or O/D gearBelow 1.5
SL (E4− 8) − E1 (E4− 24)R−L − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
Vehicle driving under lock −up position9 − 14
SP2+ (E6− 2) − SP− (E6− 8)V − V−G
IG OFF Disconnect ECM connector560 − 680 Ω
Engine is runningPulse signal is output
Below 1.5 ↔ 4 − 6
OD1 (E7− 18) − E1 (E4− 24)G−O − BR− BIG ON9 − 14
OD2 (E7− 19) − E1 (E4− 24)P−L − BR− BO/D main switch ON (O/D OFF)Below 3
O/D main switch OFF (O/D ON)9 − 14
OIL (E5− 12) − E2 (E5− 9)R−W − BR− BATF temperature: 110 °C (230° F)Below 1.5
L (E7−17) − E1 (E4− 24)G−W − BR− BIG ON Shift lever L position7.5 − 14
IG ON Shift lever other than L positionBelow 1.5
2 (E7−16) − E1 (E4− 24)O − BR− BIG ON Shift lever 2 position7.5 − 14
IG ON Shift lever other than 2 positionBelow 1.5
R (E7−15) − E1 (E4− 24)R−B − BR− BIG ON Shift lever R position7.5 − 14
IG ON Shift lever other than R positionBelow 1.5
NSW (E7−22) − E1 (E4− 24)B−W − BR− BIG ON Shift lever P or N positionBelow 3
IG ONShift lever other than P and N position9 − 14
STP (E7− 14) − E1 (E4− 24)G−W − BR− BIG ON Brake pedal is depressed7.5 − 14
IG ON Brake pedal is releasedBelow 1.5
THW (E5−4) − E2 (E5− 9)R−W − BR− BIG ON Engine coolant temperature 80 °C (176° F)Below 1.5
IDL (E5− 11) − E2 (E5− 9)G−W − BR− BIG ON Accel. pedal is releasedBelow 1.5
IG ONAccel. pedal is depressed9 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−148
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
No down−
shift (O/D → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (3rd → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (2nd → 1st)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−157 DI−35
DI−87
DI−166 −
−
DI−145
Lock− up does not engage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. Park/neutral position switch circuit
7. Engine coolant temp. sensor circuit
8. On −vehicle repair matrix chart
9. Off −vehicle repair matrix chart
10.ECMDI−163
DI−35
DI−87
DI−166
DI−185
DI−169 DI−30 −
−
DI−145
Lock− up does not disengage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163 DI−35
DI−87
DI−166
DI−185 −
−
DI−145
Shift point too high or too low
1. Throttle position sensor circuit
2. Pattern select switch circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. ECMDI−35
DI−179 DI−87
DI−166
DI−145
Up− shifts to 2nd while in L position
Up− shifts to 3rd while in L position1. Park/neutral position switch circuit
2. ECMDI−169
DI−145
Up− shifts to O/D from 3rd while O/D main switch is OFF1. O/D main switck& O/D OFF indicator light circuit
2. ECMDI−174
DI−145
Up−shift to O/D from 3rd while engine is cold
1. Engine coolant temp. sensor circuit
2. On −vehicle repair matrix chart
3. Off −vehicle repair matrix chart
4. ECMDI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−149
1996 LAND CRUISER (RM451U)
Harsh engagement (N
→ D)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. Park/neutral position switch circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163
DI−154 DI−35
DI−169 −
−
DI−145
Harsh engagement (Lock −up)
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163 DI−35
DI−87
DI−166 −
−
DI−145
Harsh engagement (Any driving position)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. No. 1 vehicle speed sensor circuit
5. No. 2 vehicle speed sensor circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163
DI−154 DI−35
DI−87
DI−166
−
−
DI−145
Slip or shudder (Forward and reverse)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Slip or shudder (A particular position)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No engine braking1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Poor acceleration
1. Throttle position sensor circuit
2. No. 1 vehicle speed sensor circuit
3. No. 2 vehicle speed sensor circuit
4. Shift solenoid valve No. 1 and No. 2 circuit
5. Shift solenoid valve SL circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chartDI−35
DI−87
DI−166
DI−157
DI−163 −
−
No kick− down
1. Throttle position sensor circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. On−vehicle repair matrix chart
5. ECMDI−35
DI−157 DI−87 −
DI−145
No pattern select1. Pattern select switch circuit
2. ECMDI−179
DI−145
No 2nd start
1. Pattern select switch circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. ECMDI−179
DI−157
DI−145
Large shift shock or engine stalls when starting off or stopping
1. Shift solenoid valve SL circuit
2. Stop light switch circuit
3. Off −vehicle repair matrix chart
4. ECMDI−163
DI−185 −
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−150
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Chapter 2: On−Vehicle Repair
(  : A340F, A343F Automatic Transmission Repair Manual Pub. No. RM479U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion
1. Throttle cable
2. Transmission control rod
3. Manual valve
4. Primary regulator valve
5. Parking lock pawl
6. Off−vehicle repair matrix chartDI−131
DI−131


−
Vehicle does not move in R position1. Off −vehicle repair matrix chart−
Vehicle does not move in a particular position or positions
(Except R position)1. Off −vehicle repair matrix chart−
No up− shift (1st → 2nd)1. 1 −2 shift valve
2. Off −vehicle repair matrix chart
−
No up −shift (2nd → 3rd)1. 2−3 shift valve
2. Off −vehicle repair matrix chart
−
No up− shift (3rd → O/D)1. 3−4 shift valve
2. Off −vehicle repair matrix chart
−
No down− shift (O/D → 3rd)1. 3−4 shift valve
No down −shift (3rd → 2nd)1. 2−3 shift valve
No down −shift (2nd → 1st)1. 1−2 shift valve
2. Off −vehicle repair matrix chart
−
Lock− up does not engage or lock −up does not disengage1. Lock− up relay valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (N → D)1. Accumulator control valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (Lock −up)1. Lock− up control valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (N → R)
1. Accumulator control valve
2. C
2 accumulator
3. Off −vehicle repair matrix chart


−
Harsh engagement (N → L)1. Low coast modulator valve
Harsh engagement (1st → 2nd (D position))1. Accumulator control valve
2. B
2 accumulator


Harsh engagement (1st
→ 2nd (2 position))1. Accumulator control valve
2. B
2 accumulator


Harsh engagement (2nd
→ 3rd → O/D)1. Cut− back valve
Harsh engagement (1st → 2nd → 3rd → O/D)1. Throttle valve
2. Accumulator control valve

Harsh engagement (2nd → 3rd)
3. Accumulator control valve
1. C
2 accumulator
2. Off −vehicle repair matrix chart


−
Harsh engagement (3rd → O/D)
1. Accumulator control valve
2. B
0 accumulator
3. Off −vehicle repair matrix chart


−
Harsh engagement (O/D → 3rd)
1. Accumulator control valve
2. C
0 accumulator
3. Off −vehicle repair matrix chart


−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−151
1996 LAND CRUISER (RM451U)
Slip or shudder (Forward and reverse)
1. Throttle cable
2. Transmission control rod
3. Oil strainer
4. Pressure relief valve
5. Off
−vehicle repair matrix chartDI−131
DI−131

−
Slip or shudder (Particular position)
1. Throttle cable
2. Transmission control rod
3. Off −vehicle repair matrix chartDI−131
DI−131
−
No engine braking (1st (L position))1. Low coast modulator
2. Off −vehicle repair matrix chart
−
No engine braking (2nd (2 position))1. 2nd coast modulator
2. Off −vehicle repair matrix chart
−
No kick− down1. 1−2 shift valve
2. 2 −3 shift valve

Chapter 3: Off −Vehicle Repair
(  : A340F, A343F Automatic Transmission Repair Manual Pub. No. RM479U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion1. O/D one− way clutch (F0)
2. O/D planetary gear unit
3. Torque converter clutch

AT −26
Vehicle does not move in R position
1. 2nd coast brake (B1)
2. Front and rear planetary gear unit
3. Direct clutch (C
2)
4. 1st and reverse brake (B
3)




Vehicle does not move in D, 2 and L positions1. Forward clutch (C1)
Vehicle does not move in D and 2 positions1. No. 2 one− way clutch (F2)
Vehicle does not move in 2 position1. 1st and reverse brake (B3)
Vehicle does not move in L position
1. 2nd brake (B2)
2. 2nd coast brake (B
1)
3. Direct clutch (C
2)



No up− shift (1st → 2nd)1. 2nd brake (B2)
2. No. 1 one− way clutch (F
1)


No up−shift (2nd → 3rd)1. Direct clutch (C2)
No up−shift (3rd → O/D)1. O/D brake (B0)
No down−shift (2nd → 1st)1. 2nd brake (B2)
Lock−up does not engage or lock −up does not disengage1. Torque converter clutchAT −26
Harsh engagement (N → D)
1. Forward clutch (C1)
2. O/D one− way clutch (F
0)
3. No. 2 one− way clutch (F
2)



Harsh engagement (N → R)
1. Direct clutch (C2)
2. 1st and reverse brake (B
3)
3. O/D one− way clutch (F
0)



Harsh engagement (2nd → 3rd)1. Direct clutch (C2)
Harsh engagement (3rd → O/D)1. O/D brake (B0)
2. O/D planetary gear unit

Harsh engagement (O/D → 3rd)1. O/D one− way clutch (F0)
Harsh engagement (Lock −up)1. Torque converter clutchAT −26
Slip or shudder (Forward and reverse (After warm −up))
1. Torque converter clutch
2. O/D one− way clutch (F
0)
3. O/D direct clutch (C
0)
AT −26


Slip or shudder (Forward and reverse (Just after engine starts))1. Torque converter clutchAT −26
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08221 Q08220D00081
(+) (−)
(+) (−)Air
DI−156
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P0750, P0755 Shift Solenoid A/B Malfunction (Shift Solenoid Valve No. 1/No. 2)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gea\
r position (1st, 2nd, 3rd or O/D
gear).
Then the ECM compares the actual gear with the shift schedule in the ECM mem\
ory to detect mechanical
trouble of the shift solenoid valves and valve body.
DTC No.DTC Detecting ConditionTrouble Area
P0750
P0755During normal driving, the gear required by the ECM does not
match the actual gear (2 trip detection logic)Shift solenoid valve No. 1/No. 2 is stuck open or closed
 Valve body is blocked up or stuck
HINT:
Check the shift solenoid valve No. 1 when DTC P0750 is output and check shift\
solenoid valve No. 2 when
DTC P0755 is output.
INSPECTION PROCEDURE
1 Check shift solenoid valve No. 1 or No. 2 operation.
PREPARATION:
(a) Remove the oil pan.
(b) Remove the shift solenoid valve No. 1 or No. 2.
CHECK:
(a) Applying 490 kPa (5 kgf/cm2, 71 psi) of compressed air,
check that the shift solenoid valve does not leak air.
(b) When battery positive voltage is supplied to the shift sole-
noid valves, check they opens.
NG Replace shift solenoid valve No. 1 or No. 2.
OK
2 Check valve body (See page DI−147 ).
NG Repair or replace valve body.
OK
Repair transmission (See page AT −18).
DI5KM−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010