1996 TOYOTA LAND CRUISER Cruise control

BE1MN−01
Z06854
LEFT SIDEOFF
RIGHT SIDE
UP
RIGHT SIDE
DOWN
LEFT OFF
−
BODY ELECTRICAL POWER MIRROR CONTROL SYSTEM
BE−69
1996 LAND CRUISER (RM451U)
INSPECTION
1. Left side:
INSPECT MIRROR SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
UP1 − 10, 3 − 4Continuity
DOWN1 − 3, 4 − 10Continuity
LEFT1 − 9, 3 − 4Continuity
RIGHT1 − 3, 4 − 9Continuity
2. Off:
INSPECT MIRROR SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
UP3 − 4Continuity
DOWN1 − 3Continuity
LEFT3 − 4Continuity
RIGHT1 − 3Continuity
3. Right side:
INSPECT MIRROR SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
UP1 − 6, 3 − 4Continuity
DOWN1 − 3, 4 − 6Continuity
LEFT1 − 2, 3 − 4Continuity
RIGHT1 − 3, 2 − 4Continuity
If continuity is not as specified, replace the switch.
4. INSPECT MIRROR MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal in col-
umn ”A” and the negative ( −) lead to terminal in column ”B”,
check that the mirror operates in column ”C”.
Switch positionTester connectionSpecified condition
A (+)B (−)C (Operation)
23Mirror turns
upward
32Mirror turns
downward
13Mirror turns to
left side
31Mirror turns to
right side
If operation is not as specified, replace the mirror assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37N−01
BO2455
Cotton
TapePanel
Cover
−
BODY FRONT DOOR
BO−9
1996 LAND CRUISER (RM451U)
DISASSEMBLY
HINT:
Tape a screwdriver tip before using to pry parts.
1. REMOVE DOOR INSIDE HANDLE BEZEL
2. REMOVE ARMREST
3. REMOVE ARMREST PANEL BASE UPPER
4. REMOVE COURTESY LIGHT
5. REMOVE LOWER FRAME BRACKET GARNISH
6. REMOVE DOOR TRIM
(a) Remove the 3 screws from the door trim.
(b) Using a screwdriver, remove the clip and remove the trim
by pulling all of the trim up.
(c) Remove the 11 screws and armrest base from the door
trim.
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 8 screws and door pocket from the door trim.
7. REMOVE DOOR BELT MOULDING
Pry out the clip from the edge of the panel, and remove the
moulding .
8. REMOVE DOOR WEATHERSTRIP
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
9. REMOVE DOOR INSIDE HANDLE
10. REMOVE DOOR LOCK CONTROL RELAY
11. REMOVE SERVICE HOLE COVER
NOTICE:
Do not block the trim clip sealing with the tape.
12. REMOVE OUTSIDE REAR VIEW MIRROR
13. REMOVE DOOR GLASS RUN
14. REMOVE REAR LOWER FRAME
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−10
−
BODY FRONT DOOR
1996 LAND CRUISER (RM451U)
HINT:
At the time of reassembly, adjust the equalizer arm up to down
and tighten if where dimensions A and B, as shown are equal.
15. REMOVE DOOR GLASS
16. REMOVE WINDOW REGULATOR
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face and gears of the window regulator.
NOTICE:
Do not apply grease to the spring.
17. REMOVE LOCKING AND OPENING CONTROL LINK
18. REMOVE DOOR LOCK
HINT:
At the time of reassembly, apply adhesive to the 3 screws. Part No.08833 −00070, THREE BOND 1324 or equiva-
lent
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face of the door lock.
19. REMOVE DOOR OUTSIDE HANDLE
20. REMOVE DOOR LOCK CYLINDER
21. REMOVE DOOR SPEAKER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37W−01
−
BODY BACK DOOR
BO−21
1996 LAND CRUISER (RM451U)
DISASSEMBLY
HINT:
Tape the screwdriver tip before using to pry parts.
1. REMOVE UPPER BACK DOOR
(a) Remove the pull handle and pull handle bezel.
(b) Remove the back door trim.
(1) Insert a screwdriver, between the retainers and trim
to pry it loose.
(2) Remove the back door trim.
(c) Remove the door weatherstrip.
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
(d) Remove the weatherstrip upper.
NOTICE:
Do not pull strongly off the weatherstrip as it may tear.
(e) Remove the door inside handle.
(f) Remove the door lock control.
(g) Remove the outside handle.
(h) Remove the door lock cylinder.
(i) Remove the wiper arm.
(j) Remove the wiper motor.
(k) Remove the wiper control relay.
(l) Remove the door lock.
(m) Remove the damper stay.
2. REMOVE LOWER BACK DOOR
(a) Remove the door trim. (1) Insert a screwdriver, between the retainers and
door trim to pry it loose.
(2) Remove the door trim.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO2455
Panel
Cotton Tape Cover
BO−22
−
BODY BACK DOOR
1996 LAND CRUISER (RM451U)
(b) Remove the service hole cover.
(c) Remove the door lock control.
(d) Remove the door lock.
(e) Remove the license plate light cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO385−01
−
BODY REAR WIPER AND WASHER
BO−31
1265
Author: Date:
1996 LAND CRUISER (RM451U)
REAR WIPER AND WASHER
REMOVAL
1. REMOVE PULL HANDLE AND PULL HANDLE BEZEL
2. REMOVE BACK DOOR TRIM
(a) Insert a screwdriver between the retainers and door trim
to pry it loose.
HINT:
Tape the screwdriver tip before use.
(b) Remove the back door trim.
3. REMOVE WIPER ARM, MOTOR AND REAR WIPER CONTROL RELAY
(a) Open the cap.
(b) Remove the nut and wiper arm.
(c) Remove the 5 bolts and motor, then disconnect the con- nector.
(d) Remove the bolts and rear wiper control relay,then dis- connect the connector.
4. ADJUST REAR WASHER NOZZLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO387−01
−
BODY REAR WIPER AND WASHER
BO−33
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WIPER CONTROL RELAY
2. INSTALL WIPER MOTOR
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
3. INSTALL BACK DOOR TRIM
4. INSTALL PULL HANDLE BEZEL
5. INSTALL PULL HANDLE
6. INSTALL REAR WIPER ARM
(a) Install the wiper arm and operate the wipers once and turn
the wiper switch OFF.
(b) Adjust the installation positions of the wiper arm to the positions shown in the illustration.
A: Approx. 40 mm (1.57 in.)
(c) Tighten the nut. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−64
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
11. REMOVE FRONT SEAT OUTER BELT SHOULDER AN-
CHOR
12. REMOVE CENTER PILLAR UPPER GARNISH
13. REMOVE FRONT SHOULDER BELT ANCHOR AD-
JUSTER
14. REMOVE NO. 1 REAR SEAT OUTER BELT SHOUL- DER ANCHOR
15. w/ No. 2 Rear Seat REMOVE NO. 2 REAR SEAT OUTER BELT SHOUL-
DER ANCHOR
16. REMOVE QUARTER AND REAR PILLAR GARNISH
17. REMOVE ASSIST GRIPS
18. REMOVE FRONT PILLAR GARNISH
19. REMOVE SUN VISORS AND HOLDERS
20. REMOVE INNER REAR VIEW MIRROR
21. REMOVE PERSONAL LIGHT ASSEMBLY AND PER- SONAL LIGHT COVER
22. REMOVE NO. 1 AND NO. 2 ROOM LIGHT
23. REMOVE BACK DOOR OPENING TRIM
24. REMOVE SLIDING ROOF OPENING MOULDING
25. REMOVE CONTROL SWITCH
(a) Remove the screw.
(b) Using a screwdriver, remove the switch cover.
(c) Remove the 2 screws and switch body, then disconnect the connector.
(d) Remove the 2 screws and bracket.
26. REMOVE ROOF HEADLINING
(a) Using the clip remover, remove the 7 clips.
(b) Remove the roof headlining.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010