1996 TOYOTA LAND CRUISER Cruise control

BO4033
−
BODY SLIDING ROOF
BO−65
1996 LAND CRUISER (RM451U)
27. REMOVE DRIVE GEAR ASSEMBLY
(a) Remove the bolt and drive gear control relay, then discon-
nect the connector.
(b) Remove the 2 bolts and bracket.
(c) Remove the 4 bolts and drive gear assembly, then discon-
nect the connector.
28. REMOVE SLIDING ROOF GARNISHES
Using a screwdriver, pry loose the 2 clips and remove the inner
side garnish.
29. REMOVE SLIDING ROOF GLASS
(a) Remove the 6 nuts and shims.
HINT:
Make sure of the number of shims.
(b) Pull the glass upward to remove it.
30. REMOVE DRIP CHANNEL
(a) Remove the 2 screws.
(b) Pull the channel forwards to remove it.
31. REMOVE WIND DEFLECTOR
Remove the 4 screws and wind deflector.
32. REMOVE SLIDING ROOF HOUSING
(a) Disconnect the drain hose.
(b) Remove the 3 nuts, 12 screw and housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO4047
Point Marks
BO−66
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
33. ADJUST DRIVE RAIL
HINT:
Adjust the drive rail to a closed and tilted down position.
Using a screwdriver, slide the link forward or backward to align
the 2 marks, as shown.
34. ADJUST AND INSTALL DRIVE GEAR ASSEMBLY
(a) Remove the screw and cam plate cover.
(b) Remove the large screw, washers and shims.
(c) Turn the drive shaft by screwdriver to align the housing
and gear point mark, as shown.
(d) Install the cam plate cover with the screw.
(e) Install the drive gear assembly with 4 bolts.
(f) Connect the connector.
35. INSTALL DRIVE GEAR CONTROL RELAY AND BRACKET
(a) Install the bracket with 2 bolts.
(b) Install the drive gear control relay with the bolt, then con-
nect the connector.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO5152
BO391−01
BO−68
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SLIDING ROOF GLASS ALIGNMENT
(a) Start the engine and check the operation time of the slid-
ing roof.
Operation time: Approx. 5 sec.
(b) Check for abnormal noise or binding during operation.
(c) With the sliding roof fully closed, check for water leakage.
(d) Check for a difference in level between the sliding roof weatherstrip and roof panel.
Front End0.9 − 3.9 mm (0.035 − 0.154 in.)
Rear End0.9 − 3.9 mm (0.035 − 0.154 in.)
2. If the sliding roof does not operate:
ADJUST SLIDING ROOF GLASS ALIGNMENT
(a) Remove the control switch cover.
(b) Remove the large screw inside.
NOTICE:
Be careful not to lose the spring washer or shim.
(c) Manually operate the moon roof by inserting a special
crank−shaped screwdriver into the hole and turning the
drive shaft.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY INSTRUMENT PANEL
BO−77
1996 LAND CRUISER (RM451U)
15. REMOVE CENTER CLUSTER FINISH PANEL WITH
HEATER CONTROL ASSEMBLY
(a) Using a screwdriver, take off the 2 claws, then remove the
cup holder hole cover.
HINT:
Tape the screwdriver tip before use.
(b) Take off the ashtray.
(c) Remove the center cluster finish panel with heater control
assembly, then disconnect the connectors.
(d) Remove the 2 screws and heater control assembly from the center cluster finish panel.
16. REMOVE RADIO
17. REMOVE GLOVE COMPARTMENT DOOR
18. REMOVE SPEAKER PANEL AND SPEAKER
19. REMOVE FRONT AND REAR CONSOLE BOX
20. DISCONNECT AIRBAG CONNECTOR
(a) Remove the airbag connector from the airbag bracket.
NOTICE:
When handling the airbag connector , take care not to dam-
age the airbag wire harness.
(b) Disconnect the airbag connector.
21. REMOVE INSTRUMENT PANEL
(a) Remove the 5 screws and 9 bolts.
(b) Remove the instrument panel. Torque: 20 N·m (210 kgf·cm, 15 ft·lbf) for passenger
airbag bolts
22. REMOVE INSTRUMENT PANEL REINFORCEMENT
(a) Remove the 2 bolts and lower instrument panel reinforce-
ment.
(b) Remove the 2 bolts, 2 nuts and No. 1 brace.
(c) Remove the 4 bolts, 4 nuts and instrument panel rein- forcement.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DI−01
−
BRAKE ABS ACTUATOR
BR−53
1035
Author: Date:
1996 LAND CRUISER (RM451U)
ABS ACTUATOR
ON−VEHICLE INSPECTION
1. INSPECT BATTERY POSITIVE VOLTAGE
Battery positive voltage: 10 − 14 V
2. DISCONNECT CONNECTORS
(a) Disconnect the connector from the actuator.
(b) Remove the control relay from the actuator bracket.
(c) Disconnect the 2 connectors from the control relay.
3. CONNECT ACTUATOR CHECKER (SST) TO ACTUA-
TOR
(a) Connect the actuator checker (SST) to the actuator, con-
trol relay and body side wire harness through the sub −
wire harness C (SST) and E (SST), as shown.
SST 09990−00150, 09990 −00200, 09990−00210
(b) Connect the red cable of the checker to the battery posi- tive (+) terminal and black cable to the negative ( −) termi-
nal. Connect the black cable of the sub −wire harness to
the battery negative (−) terminal or body ground.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1334
−
BRAKE ABS ACTUATOR
BR−55
1037
Author: Date:
1996 LAND CRUISER (RM451U)
7. DISCONNECT ACTUATOR CHECKER (SST) FROM
ACTUATOR
Disconnect the actuator checker (SST) and sub−wire harness
(SST) from the actuator, control relay and body side wire har-
ness.
SST 09990−00150, 09990 −00200, 09990−00210
8. CONNECT CONNECTORS
(a) Connect the 2 connectors to the control relay.
(b) Connect the connector to the actuator.
(c) Install the control relay to the actuator bracket.
9. CLEAR DTC (See page DI−190 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DK−01
−
BRAKE ABS ACTUATOR
BR−57
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE CONTROL RELAY FROM ACTUATOR
BRACKET
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
2. DISCONNECT BRAKE LINES
Using SST, disconnect the brake lines from the ABS actuator. SST 09023−00100
Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)
3. REMOVE ABS ACTUATOR ASSEMBLY
(a) Disconnect the 2 connectors from the actuator.
(b) Remove the 4 bolts and actuator assembly. Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
4. REMOVE ABS ACTUATOR
(a) Remove the 3 nuts and actuator from the actuator brack-
et.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(b) Remove the 3 holders and cushions from the ABS actua-
tor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OT−01
ENGINE CONTROL SYSTEM Check Sheet
Customer’s Name
Driver’s Name
Data Vehicle
Brought in
License No.
Model and Model
Year
Frame No.
Engine Model
Odometer Reading
km
miles
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Driveability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after− fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Datas Problem
Occurred
Problem Frequency
Condition When
Problem Occurs
Weather
Engine Operation
Engine T emp.
Place Outdoor
Temperature Constant
Sometimes ( times per day/month)Once only
Other
Fine
CloudyRainySnowyVarious/Other
Hot
Warm CoolCold (approx. °F/ °C)
Highway
SuburbsInner CityUphillDownhill
Rough road
Other
Cold
Warming upAfter Warming upAny temp.Other
Starting
Just after starting ( min.)IdlingRacing
Driving
Constant speedAccelerationDeceleration
A/C switch ON/OFF
Other
Condition of MILRemains on Sometimes light up Does not light up
NormalMalfunction code(s) (code )
Freezed frame data ( )
NormalMalfunction code(s) (code )
Freezed frame data ( )
Normal mode
(Precheck)
Check Mode
DTC Inspection Inspector’s
Name
DI−2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010