B6M0375A
B: INSPECTION
1. STARTER INTERRUPT RELAY
1) Disconnect connector of starter interrupt relay.
2) Connect battery to terminal No.1 and ground terminal
No. 2.
3) Check continuity between terminals as indicated in
table below:
When current flows. Between terminals
No. 3 and No. 5Continuity does not
exist.
When current does not flow. Between terminals
No. 3 and No. 5Continuity exists.
Between terminals
No. 1 and No. 2Continuity exists.
G6M0134
2. HEADLIGHT ALARM RELAY
1) Disconnect connector of headlight alarm relay.
2) Connect battery to terminal No. 1 and ground terminal
No. 2.
3) Check continuity between terminals as indicated in
table below:
When current flows. Between terminals
No. 3 and No. 5Continuity does not
exist.
Between terminals
No. 3 and No. 4Continuity exists.
When current does not flow. Between terminals
No. 3 and No. 5Continuity exists.
Between terminals
No. 3 and No. 4Continuity does not
exist.
Between terminals
No. 1 and No. 2Continuity exists.
B6M0376
3. ENGINE HOOD SWITCH
1) Disconnect connector of engine hood switch.
2) Check continuity between terminals when push rod is
pushed in 1.5 mm (0.059 in) of its stroke.
Terminal
Switch position12
When push rod is
pushed in.
When push rod is
released.
56
6-2SERVICE PROCEDURE
22. Security System
C: FUNCTION TEST
1. SECURITY SYSTEM OPERATION
1) Fully open all the door windows.
2) Turn the ignition switch to OFF and remove ignition key
from ignition switch.
3) Get out of the vehicle and lock the driver’s door using a
ignition key.
4) Check that the security indicator light illuminates.
5) When the security indicator light illuminates, wait for 30
seconds.
After 30 seconds, check that the light starts repeating 0.2
sec. ON and 2.4 sec. OFF sequence.
6) Unlock the driver’s door using the inside lock knob and
open the door.
Ensure that:
(1) the horn sounds and headlights flash intermittently
at 0.2 sec. ON and 0.6 sec. OFF. intervals, and
(2) the engine will not start even if the ignition switch
is turned to START.
7) Unlock the driver’s door one time using the ignition key.
Ensure the horn and headlights turn off.
8) Close and lock the driver’s door without using a ignition
key. (Set the inside lock knob to LOCK and then close the
door while lifting the outer handle).
Check that the security indicator light illuminates continu-
ously.
9) Within 30 seconds after the above step 8), unlock the
rear LH door using the inside lock knob and open the door.
Check that the security indicator light flashes at 0.5 sec.
intervals.
10) Close the rear LH door and lock the door using the
inside lock knob.
Check that the security indicator light illuminates continu-
ously.
11) Perform the above steps 9) and 10) on the rear RH
door and front RH door.
12) Within 30 seconds after above step 11) has been
finished, pull the engine hood opener lever and open the
engine hood.
Check that the security indicator light flashes at 0.5 sec.
intervals.
13) Close the engine hood completely.
Check that the security indicator light illuminates continu-
ously.
60
6-2SERVICE PROCEDURE
22. Security System
D: BASIC DIAGNOSTICS PROCEDURE
Start security system check.
Fully open all door windows and turn ignition switch OFF.
Take key out of ignition, exit vehicle and lock driver’s door.
Indicator light illuminates.
OK The light flashes.
The light does not
illuminate.
Check indicator harness.
Check security indicator light.
Check driver’s door key cylinder lock/unlock switch.
Check security control module.
Check whether switch input signal remains UNLOCK.
Check wiring harness.
Check switch input signals.
(Harnesses and switches separately)
(Tamper, door, hood, trunk and rear gate
switch)Check security control module.
Wait for 30 seconds.
Indicator light flashes at long intervals (0.2 sec. ON and 2.4 sec.
OFF).
OK
Not OK
Check security control module.
Unlock driver’s door using the inside lock knob and open door.
The horn sounds and headlights flash intermittently at 0.2 sec. ON
and 0.6 sec. OFF intervals.
The engine will not start even if the ignition switch is turned to
START. Indicator lamp goes out.
OK Starter motor runs.
All are not OK.
Check driver’s door switch.
Check wiring harness.
Check security control module.
Horn is not OK.
Check horn
operation by
pushing horn pad
on steering wheel.
OK
Not OK
Check horn.
Check horn relay.
Check security control module.
Check harness between horn relay and security control module.
Headlights are not
OK.
Check headlights
operation by
turning light switch
ON/OFF.
OK
Not OK
Check headlight
bulbs.
Check combination
switch.
Check headlight
relay.
Check starter interrupt relay.
Check wiring harness.
Check security control module.Check headlight alarm relay.
Check security control module.
Check wiring harness.
The alarm system continues to operate for 150 seconds.
OK Not OK
The horn and
headlights turn off.
The starter motor
does not run.
OK
Not OK
Check security
control module.
Unlock the driver’s door using ignition key.
Continues to next step.
88
6-2DIAGNOSTICS
6. Security System
From the previous step
Starter motor runs.
OK
Not OK
Check starter interrupt relay.
Check wiring harness.
Check security control module.
Check driver’s door unlock switch.
Lock the driver’s door without using a ignition key. (Set the inside
lock knob to LOCK and then close the door while lifting the outer
handle).
Within 30 seconds after the above step, open rear LH door.
Indicator light flashes with short intervals (1 Hz).
OK
Not OK
Check rear LH door switch.
Check rear LH door switch harness.
Check security control module.
Close and lock door.
Indicator light illuminates continuously.
OK
Perform the above steps also on the rear RH door and front RH
door.
OK
Not OK
Check rear and front RH door switches.
Check wiring harnesses.
Check security control module.
Pull engine hood opener lever and open engine hood.
Indicator light flashes at short intervals (1 Hz).
OK
Not OK
Check hood switch.
Check hood switch harness.
Check security control module.
Close engine hood.
Indicator light illuminates continuously.
SEDAN
WAGON
Unlock rear gate by operating driver’s door inside lock knob and
open rear gate.
Pull trunk opener lever and open trunk lid.Indicator light flashes at short intervals (1 Hz).
OK Not OK
Indicator light flashes at short intervals (1 Hz).
OK Not OKCheck rear gate switch.
Check rear gate switch harness.
Check security control module.
Check trunk switch.
Check trunk switch harness.
Check security control module.Close rear gate and lock by locking driver’s door using a
ignition key.
Close trunk lid.Indicator light illuminates continuously.
Indicator light illuminates continuously.Wait for 30 seconds.
Wait for 30 seconds.Indicator light flashes at long intervals (0.2 sec. ON and 2.4
sec. OFF).
Continues to next step. Continues to next step.
89
6-2DIAGNOSTICS
6. Security System
H: DIAGNOSTICS PROCEDURE FOR ENGINE
HOOD SWITCH SIGNAL
1. Check engine hood switch input signal for
security control module.
Not OK
OK
Go to next step on basic diagnostics procedure.
2. Check engine hood switch.
OK
Not OK
Replace engine hood switch.
Repair or replace wiring harness between engine
hood switch and security control module.
B6M0451A
1. CHECK ENGINE HOOD SWITCH INPUT SIGNAL
FOR SECURITY CONTROL MODULE.
1) Remove security control module without disconnecting
connector.
2) Turn engine hood switch ON/OFF and measure voltage
between security control module connector and body.
Connector & terminal / Specified voltage:
(B93) No. 10—Body / 10 V, or more (Hood
closed)
/ 1 V, max. (Hood opened)
2. CHECK ENGINE HOOD SWITCH.
Refer to 6-2 [W22B3] for inspection of engine hood switch.
95
6-2DIAGNOSTICS
6. Security System
1. General
1. GENERAL DESCRIPTION
The on-board diagnostics (OBD) system detects and
indicates a fault in various inputs and outputs of the com-
plex electronic control. CHECK ENGINE malfunction indi-
cator lamp (MIL) in the combination meter indicates occur-
rence of a fault or trouble.
Further, against such a failure or sensors as may disable
the drive, the fail-safe function is provided to ensure the
minimal driveability.
The OBD system incorporated with the vehicles within
this engine family complies with Section 1968.1, California
Code of Regulations (OBD-II regulation). The OBD system
monitors the components and the system malfunction
listed in Engine Section which affects on emissions.
When the system decides that a malfunction occurs, MIL
illuminates. At the same time of the MIL illumination or
blinking, a diagnostic trouble code (DTC) and a freeze
frame engine conditions are stored into on-board com-
puter.
The OBD system stores freeze frame engine condition
data (engine load, engine coolant temperature, fuel trim,
engine speed and vehicle speed, etc.) into on-board com-
puter when it detects a malfunction first.
If the OBD system detects the various malfunctions
including the fault of fuel trim or misfire, the OBD system
first stores freeze frame engine conditions about the fuel
trim or misfire.
When the malfunction does not occur again for three
consecutive trips, MIL is turned off, but DTC remains at
on-board computer.
The OBD-II system is capable of communication with a
general scan tool (OBD-II general scan tool) formed by ISO
9141 CARB.
The OBD-II diagnostics procedure is different from the
usual diagnostics procedure. When troubleshooting OBD-II
vehicles, connect Subaru select monitor or the OBD-II gen-
eral scan tool to the vehicle.
A: ENGINE
1. ENGINE AND EMISSION CONTROL SYSTEM
The Multipoint Fuel Injection (MFI) system is a system
that supplies the optimum air-fuel mixture to the engine for
all the various operating conditions through the use of the
latest electronic technology.
With this system fuel, which is pressurized at a constant
pressure, is injected into the intake air passage of the cyl-
inder head. The injection quantity of fuel is controlled by an
intermittent injection system where the electro-magnetic
injection valve (fuel injector) opens only for a short period
of time, depending on the quantity of air required for one
cycle of operation. In actual operation, the injection quan-
2
2-7ON-BOARD DIAGNOSTICS II SYSTEM
1. General
1Engine control module (ECM)
2Ignition coil
3Ignitor
4Crankshaft position sensor
5Camshaft position sensor
6Throttle position sensor
7Fuel injectors
8Pressure regulator
9Engine coolant temperature sensor
10Mass air flow sensor
11Idle air control solenoid valve
12Purge control solenoid valve
13Fuel pump
14PCV valve
15Air cleaner
16Canister
17Main relay
18Fuel pump relay
19Fuel filter
20Front catalytic converter
21Rear catalytic converter
22EGR valve (AT vehicles only)
23EGR control solenoid valve (AT vehicles only)
24Radiator fan
25Radiator fan relay
26Pressure sources switching solenoid valve
27Knock sensor
28Back-pressure transducer (AT vehicles only)
29Front oxygen sensor
30Rear oxygen sensor (Except 2200 cc California model)
31Pressure sensor
32A/C compressor
33Inhibitor switch
34CHECK ENGINE malfunction indicator lamp (MIL)
35Tachometer
36A/C relay
37A/C control module
38Ignition switch
39Transmission control module (TCM) (AT vehicles only)
40ABS/TCS control module (TCS equipped models)
41Vehicle speed sensor
42Data link connector (For Subaru select monitor)
43Data link connector (For Subaru select monitor and OBD-II
general scan tool)
44Two way valve
45Rear oxygen sensor (2200 cc California model only)
46Filter
5
2-7ON-BOARD DIAGNOSTICS II SYSTEM
1. General
1Engine control module (ECM)
2Ignition coil
3Ignitor
4Crankshaft position sensor
5Camshaft position sensor
6Throttle position sensor
7Fuel injectors
8Pressure regulator
9Engine coolant temperature sensor
10Mass air flow sensor
11Idle air control solenoid valve
12Purge control solenoid valve
13Fuel pump
14PCV valve
15Air cleaner
16Canister
17Main relay
18Fuel pump relay
19Fuel filter
20Front catalytic converter
21Rear catalytic converter
22EGR valve (AT vehicles only)
23EGR control solenoid valve (AT vehicles only)
24Radiator fan
25Radiator fan relay
26Pressure sources switching solenoid valve
27Front oxygen sensor
28Rear oxygen sensor (Except 2200 cc California model)
29Pressure sensor
30A/C compressor (With A/C models)
31Inhibitor switch
32CHECK ENGINE malfunction indicator lamp (MIL)
33Tachometer
34A/C relay (With A/C models)
35A/C control module (With A/C models)
36Ignition switch
37Transmission control module (TCM)
38Vehicle speed sensor
39Data link connector (For Subaru select monitor)
40Data link connector (For Subaru select monitor and OBD-II
general scan tool)
41Rear oxygen sensor (2200 cc California model)
42Knock sensor
43Back-pressure transducer (AT vehicles only)
44Filter
45Fuel tank pressure sensor
46Pressure control solenoid valve
47Fuel temperature sensor
48Fuel level sensor
49Vent control solenoid valve
50Air filter
7
2-7ON-BOARD DIAGNOSTICS II SYSTEM
1. General