1995 TOYOTA SUPRA transmission fluid

TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 No.1 vehicle speed sensor 16 160 12
 No.2 vehicle speed sensor 5.4 55 48 in.Vlbf
 O/D direct clutch speed sensor 5.4 55 48 in.Vlbf
 A/T fluid temp. sensor 15 150 11 Valve body 10 100 7 Oil strainer 10 100 7 
 Oil pan
 
 7.4
 
 75
 
 65 in.Vlbf
 Starter 37 380 27
 Rear support X Body 25 260 19
 Torque converter X Drive plate 34 340 25
 Oil cooler union nut 34 350 25
 Oil cooler pipe bracket 10 100 7
 Propeller shaft X Transmission 56 570 41 Propeller shaft X Differential 79 805 58 
 Propeller shaft center support
 
 49
 
 500
 
 36
 Propeller shaft adjusting nut 53 540 39
 Oil pan drain plug 17 175 13
 Drive plate X Torque converter 33 340 25
 Drive plate X Crankshaft 64 650 47
 
 
Transmission X Engine block 14 mm bolt
17 mm bolt 
 
37
72 
 
380
730 
 
27
53
 Park/neutral position switch X Transmission case 16 160 12
 Transmission output flange 123 1,250 90
 Shift control rod X Shift lever 13 130 9 Shift control rod X Park/neutral position switch 16 160 12 
 Exhaust pipe bracket X Transmission housing
 
 37
 
 380
 
 27
 No.2 exhaust pipe X Center exhaust pipe 58 590 43
 Rear center floor crossmember brace X Body 13 130 9
 Heat insulator X Body 5.4 55 48 in.Vlbf
AT2±118± A340E (2JZÐGTE) AUTOMATIC TRANSMISSIONSERVICE SPECIFICATIONS

ABBREVIATIONS USED IN THIS
MANUAL
 ABS Anti±Lock Brake System
 ALR Automatic Locking Retractor
 APPROX. Approximately
 A/T, ATM Automatic Transmission
 AT F Automatic Transmission Fluid
 BTDC Before Top Dead Center
 CB Circuit Breaker
 CD Compact Disc CRS Child Restraint System DOHC Double Over Head Cam 
 DP
 
 Dash Pot
 ECU Electronic Control Unit
 ELR Emergency Locking Retractor
 ESA Electronic Spark Advance
 ETR Electronic Turning Radio
 EX Exhaust
 FIPG Formed in Place Gasket
 FL Fusible Link
 Fr Front H±Fuse High Current Fuse 
 IG 
 Ignition
 IN Intake
 JB Junction Block
 LED Light Emitting Diode
 LH Left±Hand
 LSD Limited Slip Differential
 Max. Maximum
 MP Multipurpose
 M/T Manual Transmission O/D Overdrive O/S Oversize 
 P & BV
 
 Proportioning and By±pass Valve
 PCV Positive Crankcase Ventilation
 PPS Progressive Power Steering
 PS Power Steering
± INTRODUCTIONABBREVIATIONS USED IN THIS MANUALIN±37

PREPARATION
RECOMMENDED TOOLS
09200±00010 Engine Adjust Kit.
EQUIPMENT
 Dial indicator Brake disc
 Micrometer Brake disc
 Mirror Brake hose
 Thermometer 
 Torque wrench 
 Vernier calipers Parking brake drum
COOLANT
 Item Capacity Classification 
 Engine coolant 2JZ±GE M/T
(w/ Heater) A/T7.3 liters (7.7 US qts, 6.4 lmp. qts)
8.3 liters (8.8 US qts, 7.3 lmp. qts)Ethylene±glycol base
 
 
()
2JZ±GTE M/T
A/T
(q q)
9.5 liters (10.0 US qts, 8.4 lmp. qts)
9.4 liters (9.9 US qts, 8.3 lmp. qts)
LUBRICANT
 Item Capacity Classification
 
 
Engine oil (Drain and refill) (2JZ±GE)
w/ Oil filter change
w/o Oil filter change
5.3 liters (5.6 US qts, 4.7 lmp. qts)
4 9 liters (5 2 US qts 4 3 lmpqts)
API grade SH, Energy±Conserving II
multigrade engine oil or ILSAC multi-
grade engine oil and recommended 
 
w/o Oil filter change4.9 liters (5.2 US qts, 4.3 lmp. qts)grade engine oil and recommended
viscosity oil, with SAE 5W±30 being
preferred engine oil
 
 Engine oil (Drain and refill) (2JZ±GTE)
w/ Oil filter change
5.0 liters (5.3 US qts, 4.4 lmp. qts)
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multi-
 
 
g
w/o Oil filter change
(q q)
4.7 liters (5.0 US qts, 4.1 lmp. qts)
gg
grade engine oil and recommended
viscosity oil
 Manual transmission oil 2JZ±GE2.6 liters (2.7 US qts, 2.3 lmp. qts)API GL±5 SAE 75W±90
  2JZ±GTE
(q, q)
1.8 liters (1.9 US qts, 1.6 lmp. qts)Castle gear oil V160
 Automatic transmission 2JZ±GE1.6 liters (1.7 US qts, 1.4 lmp. qts)ATF DEXRON® II
 fluid (Drain and refill) 2JZ±GTE
(q, q)
1.9 liters (2.0 US qts, 1.7 lmp. qts)ATF TYPE T±II
 
 
Differential oil1.35 liters (1.43 US qts, 1.19 lmp. qts)API GL±5
Above±185 C (05 F)
SAE 90 
 
 
SAE 90
Below±185 C (05 F)
SAE 80W±90 or 80W
± MAINTENANCEPREPARATIONMA±5

Front Passenger Airbag:
Visually inspect the front passenger airbag assembly (airbag
and inflater).
wUse the diagnosis check to check if there are
abnormalities.
wCheck that there are no cuts, cracks or noticeable color
changes in the front passenger airbag door.
wRemove the front passenger airbag assembly from the
vehicle and check the wiring and front passenger airbag
door for damage and corrosion due to rusting, etc.
If necessary, replace the front passenger airbag assembly.
CAUTION:
wFor removal and replacement of the steering wheel pad
or front passenger airbag assembly, see RS section and
be sure to perform the operation in the correct order.
wBefore disposing of the steering wheel pad or front pas-
senger airbag assembly must first be deployed by using
SST (See RS section).
18. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
19. INSPECT BALL JOINTS AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.
wJack up the front of the vehicle and support it with
stands.
wMake sure the front wheels are in a straight±ahead
position, and depress the brake pedal.
wJack up the lower suspension arm until there is about
half a load on the front coil spring.
wMove the front wheel up and down and check that the
ball joint has no excessive play.
Maximum lower ball joint vertical play:
0.3 mm (0.012 in.)
If the play is greater than maximum, replace the ball joint.
(b) Visually check the dust covers for damage.
20. I NSPECT TRANSMISSION OIL (FLUID) AND
DIFFERNTIAL OIL
Visually check the transmission and differential for oil (fluid)
leakage.
If leakage is found, check for the cause and repair.
± MAINTENANCEMAINTENANCE OPERATIONSMA±13

21. REPLACE TRANSMISSION OIL (FLUID) AND
DIFFERENTIAL OIL
A. Replace manual transmission oil
(a) Remove the filler and drain plugs, and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add fresh oil untill it begins to run out of the filler hole.
Transmission oil:
2JZ±GE
Oil grade
API GL±5
Viscosity
SAE 75W±90
Capacity
2.6 liters (2.7 US qts, 2.3 lmp. qts)
2JZ±GTE
Oil
Castle gear oil V160
Capacity
1.8 liters (1.9 US qts, 1.6 lmp. qts)
B. Replace automatic transmission fluid
(a) Remove the drain plug, and drain the fluid.
(b) Clean the drain plug.
(c) Reinstall the drain plug securely.
(d) With the engine OFF, add new fluid through the dip±stick
tube.
Transmission fluid:
2JZ±GE
Fluid type
ATF DEXRON® II or equivalent
Drain and refill capacity
1.6 liters (1.7 US qts, 1.4 lmp. qts)
2JZ±GTE
Fluid type
ATF type T±II or equivalent
Drain and refill capacity
1.9 liters (2.0 US qts, 1.7 lmp. qts)
(e) Start the engine and shift the selector into all positions from
ºPº through ºLº, and then shift into ºPº position.
(f) With the engine idling, check the fluid level. Add fluid up the
ºCOOLº range on the dipstick. MA±14
± MAINTENANCEMAINTENANCE OPERATIONS

18. BRAKE PEDAL
(a) Check that pedal for smooth operation.
(b) Check that the pedal has the proper reserve
distance and freeplay.
(c) Check the brake booster function.
19. BRAKES
At a safe place, check that the brakes do not
pull to one side when applied.
20. PARKING BRAKE
(a) Check that the pedal has the proper travel.
(b) On a safe incline, check that the vehicle is
held securely with only the parking brake
applied.
21. AUTOMATIC TRANSMISSION PARK
MECHANISM
(a) Check the lock release button of the selector
lever for proper and smooth operation.
(b) On a safe incline, check that the vehicle is
held securely with the selector lever in the ºPº
position and all brakes released.
UNDER HOOD
22. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
23. ENGINE COOLANT LEVEL
Check that the coolant level is between the
LEVEL lines on the see±through reservoir at
normal temperature (20°C (68°F)).
24. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean
and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or
loose connections.
25. BATTERY ELECTROLYTE LEVEL
Check the indicator.
When the indicator color is blue, the condition
is satisfactory. A red color indicates that dis-
tilled water must be added, and white indi-
cates that charging is necessary.
26. BRAKE FLUID LEVEL
Check that the brake fluid level is near the up-
per level line on the see±through reservoir.27. ENGINE DRIVE BELT
Check drive belt for fraying, cracks, wear or
oil contamination.
28. ENGINE OIL LEVEL
Check that level on the dipstick with the en-
gine turned off.
29. POWER STEERING FLUID LEVEL
Check the level on the dipstick.
The level should be in the ºHOTº or ºCOLDº
range depending on the fluid temperature.
30. A U TO M AT I C TRANSMISSION FLUID
LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking and
foot brake applied, shift the selector into all
positions from ºPº to ºLº, and then shift into ºPº
position.
(c) Turn and pull out the dipstick and wipe off the
fluid with a clean rag.
Re±insert the dipstick fully and check that the
fluid level is in the ºHOTº range.
(d) Perform this check with the fluid at normal
driving temperature (70±80°C (158±176°F)).
If the level is at the low side, add fluid.
NOTICE: Do not overfill.
HINT: Wait about 30 minutes before checking
the fluid level after extended driving at high
speeds in hot weather, driving in heavy traffic
or with a trailer.
31. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose
supports.
If any change in the sound of the exhaust or
smell of the exhaust fumes is noticed, have
the cause located and correted. MA±18
± MAINTENANCEGENERAL MAINTENANCE

(c) Lift the engine out of the vehicle slowly and carefully.
NOTICE: Remove the engine and transmission assembly care-
fully without damaging the shift lever retainer (M/ T), A/C com-
pressor or PS solenoid valve.
(d) Make sure the engine is clear of all wiring, hoses and cables.
(e) Place the engine and transmission assembly onto the stand.
ENGINE REMOVAL (2JZ±GTE)
1. REMOVE HOOD
2. REMOVE RADIATOR ASSEMBLY
(See radiator removal in Cooling System)
3. DRAIN ENGINE OIL
4. DRAIN FUEL FROM FUEL TANK
5. REMOVE NO.1 AIR HOSE
6. DISCONNECT CONTROL CABLES FROM THROTTLE
BODY
Disconnect these cables:
wAccelerator cable
wCruise control actuator cable
7. REMOVE AIR CLEANER AND MAF METER ASSEMBLY
(a) Remove the 3 bolts.
(b) Loosen the hose clamp, disconnect the air hose from the
intake air connector.
(c) Disconnect the MAF meter wire from the clamp on the air
cleaner case.
(d) Disconnect the MAF meter connector, and remove the air
cleaner and MAF meter assembly.
8. M/T:
REMOVE DRIVE BELT TENSIONER DAMPER
(See step 2 in timing belt removal)
9. REMOVE DRIVE BELT, FAN, FLUID COUPLING
ASSEMBLY AND WATER PUMP PULLEY
(See step 6 in water pump removal in Cooling System)
10. REMOVE CHARCOAL CANISTER
11. DISCONNECT HEATER WATER HOSES
12. DISCONNECT BRAKE BOOSTER VACUUM HOSE
13. DISCONNECT EVAP HOSE
± ENGINEENGINE MECHANICALEG±85