1995 TOYOTA SUPRA brake sensor

REAR DRIVE SHAFT REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal.
(See page BR±62)
1. REMOVE REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
2. DISCONNECT EXHAUST PIPE MOUNTING
(a) Remove the 2 exhaust pipe support rings.
(b) Support the exhaust pipe securely.
(c) Remove the 2 exhaust pipe support O±rings.
3. REMOVE COTTER PIN, LOCK CAP AND LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) While depressing the brake pedal, remove the nut.
Torque: 289 NVm (2,950 kgfVcm, 213 ftVlbf)
4. REMOVE LOWER SUSPENSION ARM BRACE
Remove the 4 bolts and lower suspension arm brace.
Torque: 18 NVm (180 kgfVcm, 13 ftVlbf)
5. REMOVE REAR DRIVE SHAFT
(a) Place matchmarks on the drive shaft and side gear shaft.
NOTICE: Do not use a punch to mark the matchmarks.
Use paint, etc.
(b) Using a 10 mm hexagon wrench, remove the 6 hexagon bolts
and 2 washers while depressing the brake pedal.
Torque: 83 NVm (850 kgfVcm, 61 ftVlbf)
INSTALLATION HINT: Apply a light coat of engine oil on the
threads of the bolts.
(c) Disconnect the inboard joint from the differential side gear
shaft.
(d) Hold the inboard joint side of the drive shaft so that the
outboard joint side does not bend too much.
± SUSPENSION AND AXLEREAR DRIVE SHAFTSA±47

UPPER SUSPENSION ARM REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal and rear wheel alignment.
(See page BR±62 and SA±9)
1. REMOVE REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
2. REMOVE REAR DRIVE SHAFT
(See page SA±46)
3. REMOVE REAR BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the rear axle
carrier.
Torque: 104 NVm (1,065 kgfVcm, 77 ftVlbf)
(b) Support the brake caliper securely.
4. DISCONNECT ABS SPEED SENSOR AND WIRE
HARNESS
(a) Remove the bolt and disconnect the speed sensor from the
axle carrier.
Torque: 8 NVm (80 kgfVcm, 69 in.Vlbf)
(b) Remove the bolt and disconnect the speed sensor wire
harness clamp from the upper suspension arm.
5. REMOVE UPPER SUSPENSION ARM
(a) Remove the nut from the upper suspension arm.
Torque: 109 NVm (1,100 kgfVcm, 80 ftVlbf)
(b) Using SST, disconnect the upper suspension arm from the
axle carrier.
SST 09628±62011
NOTICE: Be careful not to damage the dust cover.
(c) Remove the bolts, nuts and upper suspension arm.
Torque: 164 NVm (1,670 kgfVcm, 121 ftVlbf)
INSTALLATION HINT: After stabilizing the suspension,
torque the bolt and nut. SA±90
± SUSPENSION AND AXLEREAR SUSPENSION

LOWER SUSPENSION ARM AND STRUT
ROD REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal and rear wheel alignment.
(See page BR±62 and SA±9)
1. REMOVE REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
2. REMOVE REAR DRIVE SHAFT
(See page SA±46)
3. REMOVE REAR BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the rear axle
carrier.
Torque: 104 NVm (1,065 kgfVcm, 77 ftVlbf)
(b) Support the brake caliper securely.
4. REMOVE STRUT ROD
Remove the 2 bolts, nuts and strut rod.
Torque: 184 NVm (1,880 kgfVcm, 134 ftVlbf)
INSTALLATION HINT: After stabilizing the suspension,
torque the bolts.
5. REMOVE LOWER SUSPENSION ARM NO.1
(a) Remove the nut.
Torque: 59 NVm (600 kgfVcm, 43 ftVlbf)
(b) Using SST, disconnect the lower suspension arm No.1 from
the rear axle carrier.
SST 09610±20012
NOTICE: Be careful not to damage the dust boot.
(c) Remove the bolt and disconnect the parking brake cable
bracket.
(d) Place matchmarks on the adjusting cam and subframe.
(e) Remove the adjusting cam and nut.
Torque: 184 NVm (1,880 kgfVcm, 134 ftVlbf)
INSTALLATION HINT: After stabilizing the suspension,
torque the nut.
(f) Remove the lower suspension arm No.1.
± SUSPENSION AND AXLEREAR SUSPENSIONSA±93

TORQUE SPECIFICATIONS
(FRONT)
 Part tightened NVm kgfVcm ftVlbf
 Hub nut 103 1,050 76
 Lower suspension arm x Suspension crossmember 226 2,300 166 
 Lower suspension arm bracket stay Bolt
Nut 
 43
59 
 440
600 
 32
43
 
 Axle hub lock nut
 
 199
 
 2,030
 
 147
 Upper suspension arm x Subframe 164 1,670 121
 Lower suspension arm x Shock absorber bracket 52 530 38
 Tie rod end x Steering knuckle 49 500 36
 Steering knuckle x Upper suspension arm 103 1,050 76 
 Steering knuckle x Lower suspension arm 
 125 
 1,270 
 92
 Disc brake caliper x Steering knuckle 11 8 1,200 87
 ABS speed sensor x Steering knuckle 8 80 69in.Vlbf
 Front shock absorber x Body 35 360 26
 Front shock absorber x Lower suspension arm 143 1,460 106 Front shock absorber x Suspension support 29 300 22 
 Stabilizer bar link x Lower suspension arm
 
 74
 
 750
 
 54
 Stabilizer bar link x Stabilizer bar 74 750 54
 Stabilizer bar bracket x Body 18 180 13
 Steering knuckle x Dust cover 8 85 74in.Vlbf
SA±102± SUSPENSION AND AXLESERVICE SPECIFICATIONS

(REAR)
 Part tightened NVm kgfVcm ftVlbf
 Hub nut 103 1,050 76
 Rear shock absorber x Lower suspension arm No.2 137 1,400 101
 Upper suspension arm x Suspension crossmember 164 1,670 271 Rear axle carrier x Disc brake caliper 104 1,065 77 
 Lower suspension arm No.1 x Rear axle carrier
 
 59
 
 600
 
 43
 Lower suspension arm No.1 x Subframe 184 1,880 136
 Lower suspension arm No.2 x Rear axle carrier 150 1,525 11 0
 Lower suspension arm No.2 x suspension crossmember 184 1,880 136
 Lower suspension arm bracket x Subframe 18 180 13 
 ABS speed sensor x Rear axle carrier
 
 8
 
 80
 
 69in.Vlbf
 Strut rod x Rear axle carrier 184 1,880 136
 Strut rod x Body 184 1,880 136
 Rear drive shaft x Axle hub 289 2,950 213
 Upper suspension arm x Rear axle carrier 109 1,110 80 
 Backing plate x Rear axle carrier 
 26 
 260 
 19
 Rear axle carrier x Backing plate (Hexagon bolt) 180 1,825 132
 Rear drive shaft x Differential 83 850 61
 Differential x Propeller shaft 79 805 58
 
 Differential mounting bolt Front
Rear 
 123
142 
 1,250
1,450 
 90
105
 Ring gear x Differential case See page SA±71 
 Differential carrier retainer set bolt 2JZ±GTE M/T
Except 2JZ±GTE M/T 
 47
22 
 480
225 
 35
16
 
 Differential carrier cover set bolt 2JZ±GTE M/T
Except 2JZ±GTE M/T
 
 78
47
 
 800
475
 
 58
34
 
 Drain (Filler) plug
 
 49
 
 500
 
 36
 Breather plug 21 210 15
 Shock absorber x Body 26 260 19
 Suspension support x Shock absorber 27 280 20
 Stabilizer bar link x Lower suspension arm No.2 74 750 54 
 Stabilizer bar link x Stabilizer bar
 
 74
 
 750
 
 54
 Stabilizer bar bracket x Body 31 320 23
± SUSPENSION AND AXLESERVICE SPECIFICATIONSSA±103