1995 RENAULT MEGANE SCENIC light

UPPER REAR STRUCTURE
Lower hinge reinforcement
44SLower hinge reinforcement
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the left hand light
support and the end panel for a rear impact.
The rear face jig Car. 1563 (Parts Department
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4421
1Lower hinge reinforcement
2Light support reinforcement,
3End panel upper cross member
4Rear end cross member
5Tail wheel arch
6Light support3
1
1
0.8
1.2
1
44-20
K

UPPER REAR STRUCTURE
Upper hinge mounting support
44SUpper hinge mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the complete left hand
light support.
For standardisation purposes, the left hand light
support is delivered by the Parts Department without
the upper hinge mounting.
The rear face jig Car. 1563 (Parts Department
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with:
– upper hinge mounting angle bracket,
– upper hinge mounting angle bracket reinforcement.
PARTS CONCERNED (thickness in mm):
PRF4422
1Upper hinge mounting
2Upper hinge mounting reinforcement
3Light support
4Tail wheel arch3
2
1
1.2
44-23
L

UPPER REAR STRUCTURE
Lower hinge mounting support
44SLower hinge mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the left hand light
support.
For standardisation purposes, the left hand light
support is delivered by the Parts Department without
the lower hinge mounting support.
The rear face jig Car. 1563 (Parts Departme
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Assembled part with lower hinge (bolted).
PARTS CONCERNED (thickness in mm):
PRF4424
1Lower hinge mounting support
2Light support5
1
44-26
M

UPPER REAR STRUCTURE
Luggage compartment lid stop mounting support
44Luggage compartment lid stop mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the complete end
panel or the right hand side end panel, part section.
For standardisation purposes, the end panel is
delivered by the Parts Department without the luggage
compartment lid stop mounting support.
The rear face jig Car. 1563 (Parts Department
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4423
1Luggage compartment lid stop mounting
2Bumper mounting angle brackets
3Light support reinforcement,
4End panel upper cross member
5Bumper mounting angle bracket support1.5
1.8
1
1
1.8
44-28
N

NON-SIDE OPENING ELEMENTS
Tailgate
48P
148 NON-SIDE OPENING ELEMENTS
Tailgate
REMOVAL
Remove:
– the third brake light,
– the de-icing connections (B),
– the washer jet and disconnect.
Release:
– wiring harness (A),
– the two upper mounting protectors (C),
– the two hinge nuts (E),
– the balancers by removing the locking clips (D),
– the tailgate (this operation should be carried out be
two people for safety reasons).REFITTING
Before refitting it will be necessary to reseal between
the roof rear cross member and the hinges using
beading mastic.
Stick two strips of masking tape to the edge of the
tailgate, to prevent the paintwork from being scratched
during refitting.
Refit in reverse order to removal.
PRF4802
48-1
C

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
52-3
REMOVING THE LUGGAGE COMPARTMENT LID
LOCK AND STOP
After removing the trim (section 73),
Remove:
– the two mounting bolts on the stop,
– the two mounting bolts on the lock.Disconnect the connector from the lock.
Using a flat-nosed pliers, apply light pressure to the
stop (C) and remove the lock.
REFITTING
Check that the lock operates correctly.
To refit, proceed in the reverse order to removal.
16785-1R
16877R
16786R1
A

EXTERIOR PROTECTION
Front wing extender
55P
55-6
REMOVAL
After removing the front valance protector
(section 55-B),
Remove mounting screws (A).
Protect the wing using masking tape and then release
the extender using the special pliers.
Disconnect the side repeater.Remove the mounting bolts (B).
Remove:
– the front section of the mudguard,
– the mounting bolt (C).
Disconnect the connector (D) from the fog light wiring
harness.
17598R
17595R1
17599R
C

EXTERIOR PROTECTION
Front bumper (central section)
55P
55-11
PARTIAL REMOVAL INCLUDING THE CENTRAL
BUMPER AND THE EXTENDER
After removing the bumper protector
(section 55-A),
remove mounting bolts (C) and (D).
Protect the wing using masking tape and then, release
the extender using the unclipping pliers.
Disconnect the side repeater.Remove:
– the front section of the mudguard,
– the mounting bolt (E),
Disconnect the connector (F) from the fog light wiring
harness.
Remove the central mounting bolts (G).
Partially release the wing extender unit with the
bumper.
17598R1
17599R116882R1
E